Premiere Pro Ken Burns Effect Preset
StyleFrame Team7 min read
To create a Ken Burns preset in Premiere Pro, keyframe Scale (and optionally Position) on a still image in Effect Controls, add ease in and ease out, then right-click Motion and choose Save Preset. The saved preset appears in the Presets folder of the Effects panel, and you can drag it onto one clip or a whole selection. Choose the preset type carefully (Scale is the right choice for Ken Burns), because it decides how the keyframes behave on clips of different lengths.
Build the Ken Burns move first
A preset is only as good as the animation behind it, so build one clean move on a single clip before saving anything.
- Prep the still. Drop the image on the timeline, then right-click it and choose Set to Frame Size. This fits the image to the sequence while keeping the original pixels available, so a push-in to 115% or 120% doesn't soften the image the way scaling a low-res clip would.
- Open Effect Controls. Press Shift+5, or use Window > Effect Controls, and expand Motion.
- Set the start keyframe. Move the playhead to the first frame, click the stopwatch next to Scale, and enter your starting value. For a push-in, 100 is a sensible start. For a pull-out, start higher, around 115 to 120.
- Set the end keyframe. Go to the last frame and change the value. Premiere adds the second keyframe automatically once the stopwatch is on.
- Ease the motion. Right-click the first keyframe and choose Ease Out, then right-click the second and choose Ease In. If the option is greyed out, set Temporal Interpolation first. Easing removes the mechanical, linear feel that makes a default zoom look like a plugin.
- Play it back at full resolution and adjust the values until the move feels right for your pacing.
If you also want a drift, add a Position keyframe pair. Scale up slightly first (105% is a common starting point) so the frame edges never reveal empty canvas, then move Position a small amount between the first and last frames.
Save the preset
Once the move works, right-click the word Motion in Effect Controls and choose Save Preset. Give it a name that describes the move, such as "Push In 100–115 Eased" or "Pan Left 108", and add a short description. The name is what you'll search for later, so avoid "Ken Burns 1" and "Ken Burns 2".
The Save Preset dialog asks for a type, and this is where most people get inconsistent results:
- Scale: the keyframes are stretched or compressed to fit the duration of whatever clip you drop the preset on. This is the right choice for Ken Burns, because the move always spans the full clip whether it's 3 seconds or 12.
- Other types: the dialog offers other preset types that keep fixed timing instead of stretching to the clip length. Use them for moves that should happen at a set time rather than across the whole clip.
Use Scale for full-length push-ins and pull-outs, and the other types for moves that need fixed timing.
Apply it to a whole slideshow
The payoff comes when you have dozens of stills. A workflow that holds up:
- Import everything, then set a still-image duration that suits the edit. Right-click the images in the Project panel and choose Speed/Duration. Premiere's default for stills is five seconds, which is often too quick or too slow.
- Put the clips in order with Automate to Sequence, or place them by hand if you want tighter control over pacing.
- Select all clips and run Set to Frame Size.
- Open the Effects panel (Shift+7), find your preset in the Presets folder, and drag it onto the selected clips. Each clip picks up the same eased keyframes, and the preset name shows in Effect Controls.
Build a small library rather than one universal preset: push in, pull out, pan left, pan right, tilt up, tilt down, and maybe a subtle rotate. Alternate them across the sequence so consecutive photos don't all drift the same direction. Applying a different preset to every second or third clip makes a slideshow feel considered instead of automated.
Handling position presets across different images
Scale-only presets are portable. Position presets are not, because the saved values are absolute numbers. A pan tuned for a landscape photo can expose black edges on a portrait or square image, since Set to Frame Size fits each image differently.
A few ways to keep this under control:
- Keep pan presets conservative: roughly 105 to 110% scale with a modest position offset.
- Make separate preset families for landscape and portrait stills, for example "Pan Right – Landscape" and "Pan Right – Portrait".
- For hero images that matter, apply the preset and then tweak the first and last keyframes by hand. A preset gets you most of the way and saves the repetitive setup.
- Check edges at the end of each clip, since that's where the move is at its extreme.
Make the move survive dissolves
A common frustration is that the motion seems to stall or restart when a cross dissolve is added. A dissolve needs extra frames, called handles, and a still image has as many as you need, but the keyframes only span the visible clip. A fix that works well:
- Extend the clip beyond its intended length, placing the end keyframes past the point where the clip will finish.
- Trim the clip back to the length you want, then add the transition.
The move then continues through the dissolve instead of freezing partway. Doing this by hand per clip is tedious, so build the longer travel into your preset ahead of time.
Troubleshooting common problems
Image looks soft at the end of a push-in. The source resolution is too low for the scale you're asking for. Use a larger original, or upscale the still before editing.
Preset doesn't seem to do anything. Check that the keyframes actually appear in Effect Controls after you apply it. If you saved the preset with the stopwatch off, you saved a static value instead of an animation.
Motion is the wrong length. Revisit the preset type. Scale fits the clip duration, while the other types keep fixed timing.
Preset overwrote earlier adjustments. A Motion preset may change existing Motion values, so it's safest to apply it before any manual position or scale tweaks, not after.
Pan reveals black edges. Raise the base scale, reduce the position offset, or crop the image to a closer composition.
Third-party preset packs vs. building your own
Marketplace libraries offer Premiere Pro-compatible motion templates and presets. They can be useful for stylized transitions or photo-slideshow layouts, but a Ken Burns move is simple enough that building your own is usually faster than vetting a pack. The main benefit of your own presets is control: you decide the exact scale range, easing, and direction, and you can match them to your sequence resolution and pacing.
When a flat Ken Burns move isn't enough
Pan-and-zoom on a flat still has a built-in limit: nothing moves relative to anything else. For documentary work this is often exactly the look you want. For projects where a still needs to feel like a camera move, motion designers typically go beyond Premiere's Motion controls: building parallax from layered cutouts in After Effects, or projecting a photo onto geometry in Cinema 4D, Blender, or Nuke.
This is where Styleframe may serve as a complement. In practice that means your Premiere presets still handle the straightforward slideshow moves, while a dedicated tool covers the shots that need more than a scale-and-position animation.
Quick workflow summary
- Set stills to frame size and decide on a duration.
- Keyframe Scale (and a restrained Position) on one clip, with Ease Out and Ease In.
- Save with Motion > Save Preset, using the Scale type for full-clip moves.
- Build a small, clearly named library of directions.
- Apply presets across the timeline, alternating moves, then hand-check edges, dissolves, and any hero images.
- For shots that need real depth or cleaner source material, prepare them in a dedicated tool and bring the results into your compositing pipeline.
A well-named, well-eased preset library removes the most repetitive part of slideshow and documentary editing. The important decisions are the preset type, a conservative scale buffer, and easing that feels deliberate.