How to Write Text in a Circle in Procreate
StyleFrame Team6 min read
Procreate has no built-in text-on-path feature, so you have to curve text manually. The most accurate way to wrap text around a circle is to draw a circle guide with QuickShape, type your text, then rotate and place each letter along the guide. For short arcs, the Warp tool's Advanced Mesh is faster. Either way, the result is raster art, so decide on wording and spacing before you commit.
Why Procreate Can't Put Text on a Path
Photoshop and Illustrator let you click a circle with the type tool and type along it. Procreate's text tool, added to the app relatively recently, doesn't have that option. Users have been asking for text on a path in Procreate's feedback forum, and some of them still finish curved lettering in Affinity, Photoshop, or a third-party app such as Over.
Every Procreate method is therefore a workaround built from guides, transforms, and distortion. Each one trades speed against precision, and each one rasterizes the text at some point. Duplicate your text layer and hide the original before you start, so you can still edit the wording later.
Set Up Your Guides First
Good guides make the manual work much easier.
- Draw a circle. On a new layer, draw a circle with a monoline brush and hold your finger or Pencil at the end of the stroke. QuickShape snaps it to a clean circle. Before you lift, you can adjust its size.
- Find the canvas center. Open Actions > Canvas, turn on Drawing Guide, and choose Edit Drawing Guide. Increase the grid size until you see one vertical and one horizontal line crossing at the middle. Use these to center your circle exactly.
- Add a second circle. Duplicate the circle, shrink it, and center it again. The gap between the two circles should match the height of your capital letters. This gives you a baseline and a cap-height line.
- Tidy up. Put both circles in a group and lower the group's opacity so they read as guides, not artwork.
Make the canvas large. If you plan to put the lettering on a video or print, work at the final output size or larger, since rotating and warping raster text softens it.
Method 1: Warp with Advanced Mesh
This is the quickest route for text that follows an arc, such as a badge headline across the top of a circle.
- Add your text through Actions > Add > Add Text, set the font, and center it horizontally on the canvas.
- Select the text layer, tap Transform, and choose Warp, then Advanced Mesh.
- Drag the mesh points so the baseline bends along the inner guide circle. Move the points in matched pairs on either side of center so the curve stays symmetrical.
- Pull the outer points slightly to keep the letters from stretching. Warping inevitably distorts letterforms, so watch the thickness of the strokes as you go.
Warp works best for a quarter to a half circle. Past that, the mesh gets unwieldy and letters at the ends start to skew visibly. It's a good choice for casual graphics but not for logo-grade lettering.
Method 2: Place Each Letter Manually
This method takes longer and gives the cleanest result. It's the one to use for a full ring of text.
- Type the full phrase once and leave it as a reference layer.
- Create each letter as its own text layer, or rasterize the phrase and cut it into individual letters with selections. Separate text layers keep the glyphs crisp until you flatten them.
- Place the first letter at the top center of the guide, with its baseline on the inner circle.
- Use Transform to rotate each following letter around the circle center. Nudge it along the guide so the spacing looks even. Because the guide circle is visible, you can judge whether each letter's base is tangent to it.
- Work outward from the center in both directions for top text. That keeps the layout symmetrical and lets you correct spacing before errors accumulate.
Spacing is where most people go wrong. On a convex curve, the tops of letters spread apart and the bases crowd together. Add a little extra tracking by eye, and check the result at a small size, since awkward gaps are easy to miss when zoomed in.
Text on the bottom of the circle
Text at the bottom has to read left to right, which means the letters sit on the outside of the circle with their tops pointing toward the center. To do it:
- Mirror your approach: place the baseline on the outer guide circle instead of the inner one.
- Start at the bottom center and work outward in both directions.
- Rotate letters so their tops point at the circle center, not away from it.
If the bottom text comes out upside down, you have placed it against the wrong guide or rotated the letters in the wrong direction. Check the first letter before you continue.
Method 3: Liquify Push
Liquify is the least precise approach, but it works for loose, organic curves.
- Select the text layer and open Adjustments > Liquify.
- Choose Push and set a brush size that covers the section of text you want to bend.
- Drag in the direction you want the pixels to move. You're pushing existing pixels, not drawing a curve.
It's hard to predict how far the text will bend, and it can't hold a true circle. Use it for a gentle swoosh or a wavy ribbon of lettering, and use a guide circle if you need any accuracy at all.
Fix Common Problems
- Letters look jagged after rotation. Work at higher resolution, or redraw the problem letters. Repeated transforms degrade pixels, so apply each transform once when possible.
- The text doesn't close the circle evenly. Count the letters and divide the arc into equal slots first. Mark positions on the guide before placing letters, then adjust optically.
- Warped text looks stretched. Reduce how far you pull the outer mesh points, or split the phrase into two warps, one for each half.
- Letters feel unevenly weighted. Squint at the canvas. Capitals with open shapes such as V, A, and L need slightly different spacing than round letters like O and C.
- You need to edit the wording. Keep the original unrasterized text layer hidden in the file. You'll need to repeat the placement to change it.
When to Do It Outside Procreate
If the circular text is going into a motion project, consider setting it in the software where it will move. Illustrator and Photoshop offer type-on-path tools for static art.
A practical split is to do the illustration in Procreate (the ornament, the badge, the texture) and build the lettering ring in Illustrator or another app with text on a path, where it stays editable. You keep the hand-drawn feel and lose none of the control over the text.
If the lettering itself needs a hand-made, irregular look, Procreate's manual method is still the better choice. Draw it directly on the curve with the guide circle visible, and skip type altogether.
Quick Decision Guide
Pick the method that matches how the piece will be used. For anything that will be animated or revised, keep the type live outside Procreate and use Procreate for the illustration around it.