How to Wrap Text Around a Circle in Procreate
StyleFrame Team7 min read
Procreate's text tool doesn't offer a text-on-path option, so wrapping text around a circle is a manual job. The three workable methods are warping the text with Transform > Warp (Advanced Mesh), rotating each letter into place around a circular guide, or pushing the pixels with Liquify. The letter-by-letter method gives the cleanest circle, and warping is the fastest. Because both rasterize the text, finalize your wording first and keep an editable copy.
Why Procreate Makes This Harder Than Other Apps
In Illustrator, Photoshop, or Affinity Designer, you draw a circle, click it with the type tool, and the text follows the outline. Procreate's text tool has no equivalent, and users have asked for one on the Procreate Folio suggestions board. Until that changes, you either deform pixels or build the arc by hand.
For motion designers, that has a practical consequence. Anything you curve in Procreate becomes a flat raster. That is fine for a badge, a hand-lettered logo, or a texture-heavy title card. For clean, editable, animatable type, you're better off building the circle in After Effects. That route is covered later in this article.
Step 1: Build a Circle Guide
Every method below works better with a reference circle.
- Create a new layer and draw a circle with any monoline brush. Hold your stroke at the end until QuickShape snaps it to a perfect circle. While it's snapped, you can resize it before lifting.
- Find the canvas center. Open Actions > Canvas > Drawing Guide > Edit Drawing Guide and push the grid size to its maximum. The remaining blue horizontal and vertical lines mark the exact center, so you can align the circle to them.
- Draw a second, smaller circle concentric with the first. The gap between the two circles should match the cap height of your lettering. The outer circle is where the tops of the letters sit, and the inner circle is the baseline.
- Group the guides and lower their opacity so they don't distract. Don't delete them yet.
Match the circle to the artwork it will sit around. If you're framing a logo mark, make the inner circle touch the edge of the mark so the type feels attached rather than floating.
Method 1: Warp with Advanced Mesh
This is the quickest way to get text onto an arc, and it works well for shorter strings.
- Add your text with Actions > Add > Add Text, choose the font, and position it horizontally centered on the canvas.
- Duplicate the text layer and hide the original. Warping rasterizes the layer, so the duplicate is your insurance if you need to fix a typo.
- Select the duplicate, tap Transform, choose Warp, and switch to Advanced Mesh.
- Drag the mesh points so the baseline follows the inner circle and the cap line follows the outer circle. Work symmetrically from the center outward, adjusting the left and right sides in matching moves.
- Add intermediate adjustments rather than pulling a single corner a long way. Small, repeated nudges keep the letterforms from stretching unevenly.
Limits: Warp bends the glyphs along the mesh instead of rotating them, so letters at the edges of a tight curve can look sheared or pinched. It works best for an arc of roughly a half circle or less. For text that must wrap most of the way around, use Method 2.
Method 2: Place Letters One at a Time
This takes longer, but it keeps every glyph undistorted, which matters if you're delivering a logo or a lettering piece that will be scrutinized at 4K.
- Make spokes. Draw a vertical line from the center to the outer circle. Duplicate it and rotate it using Transform, keeping the angle between spokes consistent. Repeat until you have spokes spaced around the arc where the text will go.
- Type each letter as its own text layer in the same font and size. Alternatively, type the word once, rasterize a duplicate, and cut each letter out onto its own layer with a selection.
- Position each letter at the base of its spoke, with the letter's baseline on the inner circle. Use Transform to rotate it until its vertical axis lines up with the spoke.
- Adjust spacing optically. Equal angles produce uneven gaps because letters have different widths. Wide letters like M and W need more angular room than I or L, so nudge them until the rhythm looks right rather than trusting the spokes blindly.
- Merge the letters into one layer when you're satisfied, and hide the guides.
Rotating around each letter's own center puts the pivot slightly off the circle, so expect to nudge each glyph after rotating it.
Method 3: Liquify Push
Liquify works like a smudge that moves pixels. You select the text layer, open Adjustments > Liquify, choose Push, and drag in the direction you want the letters to move. Turn on the brush cursor in Prefs so you can see the size of your brush.
It is easy to start with but hard to control. You can't gauge the final curve until you've made it, and a closed circle is difficult to achieve accurately. Use it for loose, organic curves such as a ribbon or a banner, not for a precise ring. Like Warp, it rasterizes the layer, so duplicate first.
Handling the Bottom Half of a Circular Badge
Badge designs usually have text over the top and under the bottom. The bottom text should read left to right with the tops of the letters facing the center, which is the opposite curvature to the top text.
- Using Warp: Make the text, warp it along an arc that curves upward at the ends, and position it under the mark. The baseline should sit on the outer circle this time.
- Using letter placement: Rotate each letter so its baseline faces outward, then check that reading order still runs left to right.
- Shortcut: If your top and bottom arcs are identical in size, duplicate the finished top arc, flip it vertically, then retype or replace letters on the copy. Check that the letterforms are not mirrored.
Leave a visible gap between the ends of the top and bottom text, usually with a dot, star, or small ornament, so the two arcs read as one ring.
Keep the Output Production-Ready
Because curved text is raster, quality depends on the canvas you started with.
- Work large. Start the canvas at or above your final delivery size. Scaling up curved text afterward softens the edges.
- Keep a flat, editable version. Save the original text layers, the guide group, and the duplicate source in your .procreate file so changes later don't mean starting over.
- Export with transparency. Export as PNG or PSD with the background hidden so the lettering drops into a comp cleanly.
- Check for edge artifacts. Warp and Liquify can leave soft or stair-stepped edges. Zoom in to 200–300% on tight curves and clean up any rough areas.
When It's Better to Leave Procreate
If the circular text needs to be animated, rotated, tracked, or edited by a client, building it in a motion tool is faster and cleaner.
- After Effects: Desktop motion tools like After Effects can set a text layer to follow a circular path, so the text stays live and you can change the wording or the font any time.
- Premiere Pro: Build the ring in After Effects and import a rendered file.
- Cinema 4D and Blender: 3D tools like these can set text along a circular spline or curve, giving you extruded, lit, 3D lettering that Procreate can't match.
A sensible hybrid is to draw the hand-lettered artwork, ornaments, and textures in Procreate, then build the circular type in After Effects and combine them in the comp.
Quick Decision Guide
- Short phrase, half-circle arc, tight deadline: Warp with Advanced Mesh.
- Full ring, logo-grade lettering: Letter-by-letter placement.
- Loose, organic curve: Liquify Push.
- Animated, editable, or 3D type: Skip Procreate and use After Effects, Cinema 4D, or Blender.
Whichever method you choose, build the guide circles first, duplicate before you rasterize, and work at the final resolution. Those three habits prevent most of the rework people run into.