How to Use the Paint Bucket Tool in Procreate
StyleFrame Team7 min read
Procreate doesn't have a dedicated paint bucket button. Its equivalent is ColorDrop: drag the color dot from the top-right corner onto a closed shape, hold, slide left or right to set the fill threshold, then lift your Apple Pencil or finger to commit. To fill multiple areas without redragging, tap Continue Filling after the first drop and tap each area in turn.
Where the Paint Bucket Is in Procreate
Artists coming from Photoshop or Manga Studio often look for a bucket icon in the toolbar and don't find one. Procreate handles flood filling through a gesture instead. The active color swatch in the top-right corner doubles as the bucket, and you drag it onto the canvas.
Procreate also offers a few related methods, covered below: Recolor, Selections with Color Fill, and Fill Layer. Each suits a different job, so it helps to know when to reach for which.
How to Use ColorDrop, Step by Step
- Pick your color. Tap the color dot in the top right and choose a color, or just use whatever is already active.
- Select the right layer. The fill lands on the active layer. If you're coloring directly on your line art layer, select that. If you're building flats on a separate layer, see the Reference section below.
- Drag the color dot onto the area. Press the dot, drag it into the closed shape you want filled, and keep holding. Color floods in immediately.
- Adjust the threshold. While still holding, slide left or right. A percentage appears at the top of the interface. Sliding left fills less, sliding right fills more.
- Lift to commit. Release your Apple Pencil or finger to apply the fill.
If you have an iPad that supports Apple Pencil hover, you can hover the tip over your current color in the top right and double-tap the side of the Pencil to jump straight into Continue Filling with that color.
Understanding the ColorDrop Threshold
Threshold is the setting that makes ColorDrop either precise or frustrating. It controls how aggressively the fill spreads. Too low, and you get a ragged fill that leaves halos around soft or anti-aliased edges. Too high, and the color spills past your line work and floods the whole canvas.
A reliable approach:
- Drop the color, pause, and keep your contact on the screen.
- Slide gradually until the fill reaches the inside edge of your line without covering it.
- For crisp, hard-edged line art, a slightly higher threshold usually closes the fringe pixels along the line. For soft or textured brushes, expect to spend more time dialing it in.
If the fill covers the entire canvas, the threshold is almost always the cause. Undo, drop again, and slide left before releasing.
Fill Multiple Areas with Continue Filling
Dragging the color dot for every shape is slow on a busy illustration. After you perform a ColorDrop, a Continue Filling option appears. Tap it, and each subsequent tap on the canvas fills that area with the same color. You can also tap, hold, and drag to adjust the threshold for an individual fill.
To exit, tap the checkmark at the top or switch to another tool like Paint. This is the closest Procreate gets to a traditional persistent bucket tool, and it's the fastest way to lay in flat colors across many regions.
Fill Under Line Art with a Reference Layer
Most professional coloring workflows keep line art and color on separate layers so you can edit either without damage. ColorDrop supports this through the Reference function.
- Put your line art on its own layer.
- Open the Layers panel, tap the line art layer's thumbnail, and choose Reference in the Layer Options menu.
- Create a new layer beneath the line art and select it.
- Use ColorDrop. The fill respects the shapes on the Reference layer but is applied to your active layer.
This is the setup to use if you're making flat color layers for animation cleanup, separating characters into pieces for rigging in After Effects, or preparing art for later compositing. Keep in mind which layer is set as Reference, which matters when troubleshooting (see below).
Other Ways to Fill an Area
Recolor via QuickMenu
Recolor is an older fill method that Procreate brought back. It's hidden by default and accessed through QuickMenu. To enable QuickMenu, go to Actions → Prefs → Gesture Controls → QuickMenu, and choose how you want to invoke it. Then:
- Assign Recolor to one of the QuickMenu radial options and tap it.
- Choose your color in the top right.
- Tap the areas you want filled.
- Use the Flood slider to control how aggressive the fill is.
Some artists find this more natural than dragging the color dot, particularly when tapping through many small regions.
Color Fill with Selections
Selections has a Color Fill toggle that fills any selected area the instant the selection completes.
- Tap Selections at the top.
- Choose a method from the bottom tabs: Automatic, Freehand, Rectangle, or Ellipse.
- Tap Color Fill so it highlights blue.
- Pick your color from the top right.
- Make your selection; the fill applies when you finish.
This is useful for geometric shapes, backgrounds, or gradients-with-feathering. Procreate remembers the Color Fill setting between sessions, so turn it off when you're done or you'll fill things unintentionally. Color Fill works on a single layer only, not on a group of layers.
Fill Layer
To flood an entire layer with a color, select the color, open the Layers panel, tap the layer twice to open Layer Options, and choose Fill Layer. This is handy for solid backgrounds or for creating a base layer you'll then mask or clip other artwork to.
Troubleshooting ColorDrop
Most "my paint bucket isn't working" problems come down to a short list of causes:
- The whole canvas floods. The threshold is too high. Undo, drop again, hold, and slide left.
- The fill ignores your shapes or fills strangely. Another layer is probably set as Reference. Open the Layers panel, look for the Reference label on a thumbnail, and toggle it off if you didn't intend it.
- The fill leaks out of a shape. Your outline has a gap. Zoom in and close it with a brush, or lower the threshold and accept a slightly ragged fill.
- The color is white or looks transparent. Check that you're on the right layer and that the active color isn't your background color. Accidentally sampling the background with the Eyedropper is a common cause.
- Nothing happens when you drag. Confirm the color dot is visible in the top right and that you're holding while dragging, rather than tapping.
Limits to Know About
ColorDrop works one sealed region at a time. It isn't a magic wand: you can't select the entire exterior of complex line art, expand or shrink that selection, and invert it. Many artists coming from Photoshop or Manga Studio raise this as a pain point. Procreate's Automatic Selection plus Color Fill covers part of this need, but if your process relies on selection math, expect to adapt.
Fills made on a single layer also can't target a layer group with Color Fill. Plan your layer structure accordingly.
Using Procreate Flats in a Motion Pipeline
If you're a motion designer or animator, Procreate often serves as a quick illustration or styleframe sketchpad. Flat-colored layers are useful downstream: you can export layered files, bring them into After Effects, and animate characters or elements as separate pieces. Keeping fills on their own layers beneath the line art (using the Reference method above) makes that handoff much cleaner.
Quick Reference
- Basic fill: Drag the color dot from the top right onto a closed area, hold, slide to set threshold, lift.
- Fill many areas: Tap Continue Filling after a drop, then tap each region.
- Fill under line art: Set the line art layer to Reference, then ColorDrop on a layer below.
- Alternative methods: Recolor (via QuickMenu), Selections → Color Fill, and Layer Options → Fill Layer.
- When it misbehaves: Check threshold, Reference layers, gaps in outlines, and the active color.
Once you've practiced the hold-and-slide gesture a few times, ColorDrop becomes as fast as a standard paint bucket, and the Reference workflow gives you the clean, separated layers that downstream animation and compositing need.