How to Use Streamline in Procreate
StyleFrame Team6 min read
StreamLine in Procreate is a brush setting that smooths wobbles and shakes in a stroke as you draw it. To use it, tap the brush to open Brush Studio, go to the Stabilization tab, and raise the StreamLine Amount slider until the line looks smooth but still follows your hand. In Procreate Pocket, the same slider is in the brush's Stroke tab. Roughly 30-40% is a commonly recommended starting point in Procreate Pocket, and higher values make strokes feel more automated.
What StreamLine Does in Procreate
StreamLine is a stroke-smoothing control built into each brush. It reduces small shakes and jitters in your line, which matters most for inking, lettering, and calligraphy, where a single wobble is visible at any zoom level.
It has two sliders:
- Amount controls how much smoothing is applied. Higher values give a smoother, more even result. Lower values or zero give more natural, less polished linework.
- Pressure controls how pressure is smoothed across the stroke. Higher values make pressure changes build in more gradually and over a longer distance. Lower values make pressure respond faster as you press.
Because StreamLine is stored per brush, you can have a heavily smoothed inking brush and an unsmoothed sketching brush in the same set, and each behaves consistently.
How to Use StreamLine in Procreate (Step by Step)
On iPad
- Open your canvas and tap the Brush icon to open the Brush Library.
- Select the brush you want to edit. Before changing anything, swipe left on the brush and tap Duplicate. This keeps the original intact.
- Tap the duplicated brush a second time to open Brush Studio.
- In the left-hand list, select Stabilization.
- Find the StreamLine section and adjust Amount.
- Adjust Pressure if the way pressure ramps up at the start of a stroke feels too abrupt or too sluggish.
- Use the drawing pad in Brush Studio to test strokes before leaving the panel. Then go back to your canvas and draw a few real lines.
In Procreate Pocket
- Open your project and select a brush.
- Tap the brush icon in the top menu to open brush settings.
- Open the Stroke tab.
- Drag the Streamline slider to the right to increase smoothing.
Resetting a brush
If you've changed several settings and the brush feels wrong, open Brush Studio, go to About this Brush, and tap Reset Brush. This restores every setting, including StreamLine, to the brush's original values.
Choosing the Right StreamLine Amount
There is no universal correct number. The right value depends on stroke length, drawing speed, canvas size, and how much of your own hand you want to keep. These are reasonable starting points:
- Rough sketching and gesture drawing: zero or very low. You want energy and speed, not polish.
- General linework: around 30-40%. A commonly recommended range for Procreate Pocket. It evens out shakiness without removing the dynamics of your stroke.
- Clean inking, calligraphy, long curves: higher, as long as the line still follows your hand.
The risk with high values is that the line starts to feel "elastic" or automated. It lags behind your pencil and rounds off intentional corners. If you notice that, drop the value in steps of 5-10% until the brush feels responsive again. The best approach is to draw the same stroke at three or four settings on the test pad and pick the one that looks like your best hand, not a corrected one.
StreamLine vs. Stabilization
These two settings sit in the same tab and both smooth strokes, so they're easy to confuse. They work differently.
- StreamLine reduces wobbles and shakes in the line. It is the setting to reach for when your strokes look jittery.
- Stabilization takes a moving average of the stroke and draws that on the canvas. The higher it goes, the more it averages out the wobble, which tends to make strokes noticeably straighter and more deliberate.
In practice, you can combine a modest amount of each rather than maxing out one.
Brush-level vs. global stabilization
Stabilization can also be set globally. Open Actions (wrench) > Prefs > Pressure & Smoothing and adjust the Stabilization slider. A global setting applies to every brush, including ones not designed for smoothing. This is a frequent source of confusion: if your Apple Pencil suddenly feels laggy across every brush, check the global setting first. A low value of around 10-15% is a sensible place to experiment, and it's worth turning back down when you switch tasks.
When to Turn StreamLine Down or Off
Smooth isn't always better. Reduce or disable StreamLine when you need:
- Energy and gesture in sketches and animation roughs
- Texture and irregularity, such as fur, frayed edges, or hand-lettered imperfection
- Sharp corners, since heavy smoothing rounds them off
- Precise technical detail, where accuracy matters more than flow
A practical setup is to keep a few duplicated versions of your favorite brush: one with no smoothing for roughs, one with light StreamLine for general drawing, and one with higher values for final ink.
Troubleshooting StreamLine
Lines still feel corrected at zero. Procreate staff have said that no StreamLine is applied when the slider is at None. What you're seeing may be the system's predictive handling of Apple Pencil strokes. Check global Stabilization too, since it can also make lines feel corrected.
Everything feels laggy. Check global stabilization under Prefs > Pressure & Smoothing. If it's raised, it overrides your per-brush intentions.
Line ends look odd or are cut off. Very high StreamLine values can interact badly with the way a line finishes. Lower the amount and test again. If the problem persists at low values, it may be a software issue worth reporting through Procreate's support channels.
A brush feels completely wrong after tweaking. Use Reset Brush in the About this Brush tab, or delete the duplicate and start from the original.
Why Motion Artists Should Care About Clean Linework
If you work in After Effects, Premiere Pro, Cinema 4D, Blender, or Nuke, you may use Procreate for storyboards, style frames, character designs, matte paintings, hand-drawn overlays, or frame-by-frame sketches. In those cases, smoothing choices affect your downstream work:
- Storyboards and animatics: Low or zero StreamLine keeps drawings fast and gestural. Over-smoothed boards can look stiff and hide timing intent.
- Style frames and design boards: Moderate StreamLine gives clean contours that hold up when scaled in a composition. Export at a resolution that leaves headroom for your comp.
- Hand-drawn elements for compositing: Linework that will be tracked, keyed, or animated over footage benefits from consistent stroke quality. Settle on your brush settings before drawing the full set so every element matches.
- Reference art for AI-assisted workflows: Clean, consistent drawings make clearer references than shaky ones. This is a practical tip rather than a rule, but it is worth following.
Quick Reference
- Where: Brush Library > tap brush > Brush Studio > Stabilization > StreamLine (Pocket: brush settings > Stroke tab > Streamline).
- Amount: Smooths wobble. Start around 30-40% for general linework, lower for sketching.
- Pressure: Controls how gradually pressure builds across a stroke.
- Stabilization: A separate averaging control, available per brush and globally under Prefs > Pressure & Smoothing.
- Best practice: Duplicate before editing, test on the drawing pad, and keep separate brushes for rough, general, and final ink work.
Getting StreamLine right takes a few minutes of testing, and after that your brushes behave predictably. Set up your sketch, line, and ink brushes once, and your drawings will stay consistent whether they end up as a storyboard, a style frame, or a reference in your next motion project.