How to Use Procreate to Plan a Reduction Printing
StyleFrame Team7 min read
Open Procreate, build the image as a stack of layers (one per ink color), and order them from lightest to darkest. Each layer shows what stays inked on that pass, and everything you carve away shows the previous color. Use Multiply blending to approximate translucent ink, flip the canvas horizontally so the carved block prints the right way round, and export each layer as a carving guide. Planning this way lets you test colors and carving order before you cut the block, which matters because a reduction block can't be restored once carved.
What a Reduction Print Plan Needs to Answer
A reduction print uses one block for every color. You print the first color across the whole edition, carve away more of the block, print the second color, and repeat. The block is progressively destroyed, so you can't reprint the edition later.
Before you draw anything, decide:
- How many colors you'll use. Every extra color is another carving and printing pass, so a tight palette is easier to plan.
- Edition size. You must print every sheet of the first layer before carving, so commit to a number early.
- Print order. Light inks go down first and dark inks last, because darker ink covers lighter ink better than the reverse.
- Orientation. The print is a mirror image of the block, which matters most if you have text.
Procreate answers all four on screen, where mistakes cost nothing.
Set Up the Canvas
Create a canvas at the proportions of your block and paper. If you're working at a physical size, set it in inches or centimeters and use a resolution high enough to print a reference copy, such as 300 DPI. Decide on the paper margin now so the image area is correct from the start.
Then set up three groups, or at least a clear naming system:
- Reference: a rough sketch or photo you're working from.
- Ink passes: one layer per color, named by print order ("1 – cream," "2 – ochre," and so on).
- Notes: registration marks, edition notes, and a swatch strip of your actual ink colors.
Build the palette as a Procreate palette using colors sampled from your real inks, or as close as you can match them. Block printing inks mix differently from screen colors, so treat this as an approximation.
Build the Layers as Ink Passes
There are two workable ways to structure the stack. Pick one and stay consistent.
Method 1: Subtractive, Like Carving
This mirrors the physical process most closely.
- Draw the full block shape (the area that will print on the first pass) on a layer and fill it with your lightest ink color.
- Duplicate that layer for the next color and recolor it, using Alpha Lock plus a fill, or the Color Fill option.
- On the new layer, erase the areas that should stay the previous color. Those are the parts you'd carve away.
- Repeat for each pass, erasing more each time.
Each layer then looks like the block would look after that carving stage. By the last layer, only the darkest marks remain.
One pitfall: if you duplicate the whole canvas to start each layer, you'll carry white pixels into every pass, and the negative space will cover the colors beneath. Start each pass from a duplicate of the clean block-shape layer (the shape only, with no background), and erase from that.
Method 2: Additive, Like Reading the Final Image
Some printmakers prefer to think in terms of the finished image. Draw each color as the shape it should appear in the final print, then work backward to see what each pass must contain. Because later layers print over earlier ones, a shape that appears in the final print in a dark color may need to exist on the block through every earlier pass.
This is quicker for loose, graphic work but easier to get wrong on complex images. Method 1 makes the carving logic explicit.
Whichever you pick, remember the rule: the first layer is carved the least. Anything you cut away on the first pass stays the paper color for the whole print. It's the only pass where you can reveal bare paper.
Simulate Transparent Ink with Multiply
Relief inks are often slightly translucent, so overprinting changes the color. If you stack flat, fully opaque layers in Procreate, your plan will look cleaner than the real print.
To get closer:
- Set the ink-pass layers to Multiply (tap the layer's "N" and choose it from the blend mode list).
- Lower layer opacity on any pass you plan to print with a thinner or more transparent ink.
- Check overlaps of yellow-over-blue or red-over-yellow specifically, since these are where surprises happen.
If you plan to use opaque inks, leave the layers in Normal mode instead. Either way, do a small physical test with your real inks before committing the whole edition. The screen is a planning tool, not a color proof.
Check the Order and Contrast
Once the stack is built, toggle layers on and off to read each stage:
- Hide everything except pass 1. Is that the lightest, largest area?
- Reveal pass 2. Does it print over pass 1 in a darker tone?
- Continue to the last layer. Is the darkest ink always last?
Temporarily convert the composite to grayscale with an Adjustments layer or a Hue, Saturation, Brightness adjustment to check tonal separation. If two passes look the same in grayscale, the print may read flat even if the hues differ.
Also look for passes where the carving would be too fine or fragile. Tiny islands of ink are hard to carve and may lift, so simplify them in the plan.
Flip for Transfer and Export Carving Guides
Because the print is a mirror of the block, the design you transfer to the block must be reversed.
- In Procreate, use Actions > Canvas > Flip Horizontal to flip the whole canvas, or flip an individual layer with the Transform tool.
- Check any lettering. It should read correctly in the final print, which means it must be backward on the block.
Then export what you need:
- A flattened reference of the final composite (for color comparison at the press).
- Each pass as its own PNG, either by exporting layers or hiding the others and exporting one at a time.
- A high-contrast version of the first pass for transferring to the block.
Print the flipped first-pass guide for graphite transfer, or trace it with a light box. For later passes you generally carve directly on the block, using the guides as a reference rather than re-transferring.
Plan Registration and Edition Size
Reduction printing depends on every sheet landing in the same spot each time. Put the registration setup in your plan:
- Add crop or corner marks on a layer outside the image area to remind you where the paper and block sit on your registration board.
- Note the paper size and margins on the notes layer.
- Record your edition size, plus a few extra sheets for test pulls and mistakes.
You can also use Procreate's time-lapse recording or screenshots to document each pass, which is handy when you need to remember which areas you decided to keep.
Common Planning Mistakes
- Starting with the darkest ink. It will bury everything printed after it.
- Forgetting the flip. Your print will be reversed, and text will be unreadable.
- Too many colors for the time you have. Each added pass multiplies the work.
- Merging layers too early. Keep the passes separate until the print is finished, so you can reorder or adjust.
- Trusting the screen for color. Test your real ink mixes on scrap paper.
A Quick Planning Checklist
- Set the canvas to your block and paper proportions.
- Pick a limited palette sampled from real inks.
- Build one layer per pass, lightest to darkest.
- Use Multiply or opacity to approximate translucent ink.
- Check tonal separation in grayscale.
- Flip horizontally and verify any text.
- Export per-pass guides and a final composite.
- Add registration marks and decide edition size.
- Test real inks before printing the full edition.
Planning in Procreate won't carve the block for you, but it will expose most of the problems before they become permanent.