How to Use Procreate Putty
StyleFrame Team8 min read
ProCreate Putty is a two-part epoxy sculpting putty: you mix equal parts of resin and hardener into a smooth grey paste, sculpt it during a working time reported at roughly two hours, then let it cure hard. Mix a little less resin than hardener (about 40/60) for a firmer, flexible result suited to hair, tendrils, and overhanging pieces. It has been discontinued, so this guide also covers what to expect from substitutes. It is unrelated to the Procreate iPad drawing app.
What ProCreate Putty Is
ProCreate Putty was designed specifically for miniature and figure sculpting, unlike older putties adapted from other uses. It is an A/B epoxy: the resin and hardener stay workable separately and begin hardening once combined. Its reputation rests on a few properties:
- Grey color. Sculptors who paint miniatures often like working in the same tone as the finished piece, which makes proportions easier to judge.
- Low stickiness. It sticks to itself readily but clings less to tools and fingers than Green Stuff, so you need less lubrication.
- Low shape memory. It tends to stay where you push it instead of creeping back, which makes subtle adjustments easier.
- Workable after curing. Once hard, it can be carved and sanded, closer to Milliput than to Green Stuff.
- Adjustable flexibility. Changing the mix ratio changes how rigid the cured putty is.
If you came looking for the iPad app, this isn't it. The app is a digital painting tool with layers, brushes, and a color wheel. The rest of this article is about the physical material.
What You Need Before You Start
Gather everything before you combine the two parts, because the clock starts at mixing.
- Both putty components (resin and hardener)
- A clean, non-porous mixing surface such as a ceramic tile or glass
- A craft blade or knife to portion the parts
- Sculpting tools: metal tools, or silicone clay shapers (rubber-tipped, brush-like tools in various head shapes)
- A small dish of water or a suitable lubricant for tools
- Your armature, base figure, or kitbash piece, cleaned and ready to receive putty
- Gloves if you prefer not to handle epoxy directly, plus decent ventilation and a covered work surface
Check the manufacturer's safety and handling notes on the packaging, especially if you have skin sensitivities.
Step-by-Step: How to Mix and Apply It
1. Portion the two parts
Cut or pinch off the amount you need from each component. The packaging includes a guide for how much of each to use for different tasks, so follow it if you still have the box. For a standard mix, use equal amounts of resin and hardener. Start with less than you think you need; small batches are easier to finish before the putty stiffens.
2. Mix until the color is uniform
Knead the two parts together until you have a consistent grey with no streaks of white or black. Streaks mean unmixed material, which can cure unevenly or stay tacky in spots. Mixing should go quickly and cleanly compared with stickier putties.
3. Prepare the surface
Roughen smooth plastic or metal slightly so the putty has something to grip, and make sure the area is free of dust and oils. Because ProCreate is less adhesive than Green Stuff, good surface prep matters more. Pressing a thin first layer firmly into place before building up helps.
4. Build in stages
Add the putty in small masses and shape them roughly first. Establish large forms such as the folds of a cloak, the volume of a limb, or the direction of hair, then refine. Because it has low shape memory, you can push surfaces into position and expect them to stay put.
5. Refine with lubricated tools
Dampen your tools lightly. It sticks to itself eagerly, so smoothing and joining pieces is easy, but it is less clingy to tools than other putties, so you won't need much lubricant. Use silicone shapers for soft transitions and metal tools for crisp edges.
Adjusting the Mix for Flexible Results
The ratio is one of the most useful things about this putty. A standard equal mix gives you a rigid cure. If you use a bit less resin and more hardener, around 40/60, the cured result is firmer yet flexible, like stiff rubber.
That makes it a good choice for:
- Flowing hair or tendrils
- Skirt or cloth pieces
- Overhanging parts near joints that need to flex when a figure moves
Practical observations on flexible mixes:
- Longer, thinner sections flex more than short, stubby ones.
- A well-cured flexible piece can bend a long way without breaking, though overbending can leave pale stress marks, like bent plastic.
- A 40/60 ratio means one component runs out faster, so you will use up your supply unevenly.
- The ratio need not be exact, but consistency matters if you are making several matching pieces.
Note that the working window changes with ratio. With a non-standard mix, the putty may reach the stage where it springs back when poked, after which you should stop sculpting and let it cure.
Working Time and Curing
One reviewer found about two hours of working time with a 40/60 mix, so treat that as a rough guide. Early on, the putty accepts detail readily. As it stiffens, it will start to spring back when marked. When that happens, further sculpting only damages the surface, so leave it alone until it cures completely.
Tips for managing the window:
- Do your largest, most structural work first, and save fine details for the middle of the session.
- Mix small batches for detailed areas so you aren't racing the cure.
- Keep the piece somewhere dust-free and undisturbed while it hardens.
- Follow the packaging for full cure times before handling, sanding, or priming.
After It Cures: Carving, Sanding, and Finishing
Once cured, the putty can still be modified. You can carve in details you missed, sand away fingerprints or seams, and refine edges. This is a real advantage over putties that cure into a harder, less forgiving state. After sanding, you can prime and paint as you would any miniature. The material was also marketed as withstanding a number of vulcanisations, which matters if you plan to make molds and cast copies of your sculpt.
Common Mistakes
- Under-mixing. Streaks mean uneven curing. Knead until color is uniform.
- Overworking late. Once the putty springs back, stop.
- Skipping surface prep. Lower stickiness means weaker adhesion on slick surfaces.
- Mixing too much. Large batches stiffen before you can use them.
- Using the wrong ratio for the job. Equal parts for rigid details; a modified ratio for flexible parts.
- Expecting Green Stuff behavior. If you are used to a stickier, more springy putty, expect a learning curve. It is also firmer than some softer sculpting compounds.
ProCreate Putty Is Discontinued: What to Use Instead
Since production has stopped, you will need a substitute. No other putty is a perfect match, so test a few. Kneadatite Green Stuff is stickier, stays slightly malleable after setting, and holds very fine detail, but its working time is a bit shorter (around 90 minutes to two hours). Magic Sculp is known for a smooth consistency, long working time, and a finish that resists cracking even in larger structures. Apoxie Sculpt is softer than ProCreate was, and one reviewer used it as a point of comparison. Try small amounts of each, and adjust ratios where the product allows, to see which one fits your hands and your subject.
Using Physical Sculpts in a Motion Pipeline
Many motion designers, animators, and VFX artists sculpt maquettes, creature studies, or character references by hand, then need those forms on screen. A putty sculpt can make a good starting point because it carries real-world lighting, volume, and imperfection that are hard to fake. Photograph it on a clean backdrop from consistent angles, then move it into your digital workflow. Tools such as may be worth exploring for that step; check the product's site for its current features and export options.
Quick Reference
- Mix resin and hardener until a uniform grey; use equal parts for rigid work.
- Use roughly 40/60 for firmer but flexible pieces.
- Expect roughly two hours of working time (reported with a 40/60 mix); stop sculpting when it springs back.
- Lubricate tools lightly; it is less sticky than Green Stuff.
- Carve and sand after curing for final refinement.
- It is discontinued, so test alternatives in small batches.
FAQ
Is ProCreate Putty the same as the Procreate app? No. The putty is an epoxy sculpting material; the app is a digital illustration program.
Can I use it for flexible parts? Yes. Shift the mix toward more hardener (about 40/60) for a firm but bendable cure.
Can I still modify it once it has hardened? Yes, you can carve and sand it after it cures.
Where can I find it now? It has been discontinued, so look to alternatives such as Green Stuff or Magic Sculp and test them for your style of sculpting.