How to Use Procreate Color Drop
StyleFrame Team7 min read
Procreate's Color Drop fills a closed area with your active color: drag the color swatch from the top-right corner into the shape and release. If the fill floods the whole canvas or leaves gaps, hold your finger or Apple Pencil on the screen after dropping and slide left or right to adjust the Color Drop Threshold before you lift. For clean results, keep your outlines fully closed, or set your line art layer as a Reference layer so fills land on a separate layer.
What Color Drop Does in Procreate
Color Drop is Procreate's paint-bucket tool. It floods an area with color until it detects an outline, which is much faster than filling a shape with a brush. For motion work, this is how you block in flat colors on character art, backgrounds, storyboard panels, and style frames before they go into After Effects, Cinema 4D, or Blender as textures and reference.
You drag the color into the shape, and the gesture itself controls how aggressively the fill spreads.
How to Use Color Drop Step by Step
- Draw a closed shape. Make sure the outline has no breaks. Color Drop fills until it hits a boundary, and a gap lets the color escape.
- Choose your color. The active color sits in the top-right corner of the interface.
- Drag the swatch into the shape. Press the color dot, drag it into the area you want to fill, and keep your finger or Pencil down.
- Release to commit. Lifting fills the area at the current threshold.
You can also drag a color directly from a floating palette. That helps when you want a fill that differs from the outline color without switching your active color each time.
By default, the shape you're filling must be on the same layer as the line work. Two exceptions are covered below: Reference layers and Automatic Selection.
How to Adjust the Color Drop Threshold
The threshold decides how much of the area the fill covers. Most Color Drop problems come down to this setting.
- Drag your color into the shape, but don't lift.
- Hold until a thin blue bar appears along the top of the canvas with a percentage reading.
- Without breaking contact, slide right to fill more area or left to fill less.
- Lift to commit.
A few details trip people up:
- Don't touch the slider itself. You can slide anywhere on the screen. Use one finger or one Pencil, not two hands.
- Never break contact. If you lift or switch inputs mid-gesture, the adjustment ends.
- Procreate remembers your last threshold. If a fill suddenly behaves differently on a new shape, the previous setting is probably still active. Adjust it again.
- Make small moves. Slide slowly to change the percentage a point at a time, which matters for textured line work.
Troubleshooting Common Color Drop Problems
The fill floods the entire canvas
This almost always means the shape isn't closed. Zoom in and look for tiny breaks, especially where strokes meet. Undo the fill with a two-finger tap, fix the gap with a brush, and try again. If you want to confirm the diagnosis, erase a small gap in a clean shape and watch the color escape. It will fill the whole canvas every time.
Nothing fills, or the fill is too small
Your threshold may be too low. Drop the color again, hold, and slide right until the fill reaches the outline. Also check that you're on the right layer. If the outline lives on a different layer and you haven't set a Reference layer, Color Drop won't see it.
The blue slider never appears
You're probably lifting before the fill registers. Drop the color into the shape and hold still for a moment until the bar and percentage show up, then slide.
Fringes and gaps with textured brushes
Grainy brushes like chalk leave uneven edges, so a flat fill can leave gaps where pigment didn't reach the line. Raise the threshold gradually to cover more of those gaps. Expect some mismatch between a perfectly solid fill and textured linework. If you need a clean edge for compositing, draw the outline with a smooth monoline brush and add texture on a separate layer.
Fill on a Separate Layer with a Reference Layer
Keeping fills on their own layer is better for production. You can recolor, shift, or delete fills without touching the linework, and you can export layers separately for compositing.
- Open the Layers panel.
- Tap the thumbnail of your line art layer to open Layer Options.
- Tap Reference.
- Select a new layer underneath and use Color Drop as usual.
Color Drop now reads the line art from the Reference layer but paints on the active layer. Gaps in your outlines still cause flooding, so close them first. This setup is especially useful for animation cels, where you may want line, flat color, and shading as separate elements.
Fill Multiple Areas with Continue Filling
After a Color Drop, a Continue Filling option appears. Tap it, and you can fill other areas with a single tap. Tap and hold to adjust the threshold for any given fill. Exit by tapping the tick at the top or switching to another tool.
If you use an Apple Pencil on an iPad that supports hover, you can hover over your current color in the top right and double-tap the side of the Pencil to activate Continue Filling with that color. That's a real time-saver when coloring a sheet with dozens of regions.
Other Ways to Fill When Color Drop Isn't Right
Color Drop isn't the only option. Procreate offers several alternatives for different situations.
- Recolor. An older feature that Procreate brought back. It's only available through QuickMenu, which is off by default. Enable it under Actions → Prefs → Gesture Controls → QuickMenu, assign Recolor to one of the radial options, then tap areas to fill and adjust the Flood slider.
- Selections → Color Fill. Turn on Color Fill in Selections, choose a selection method (Automatic, Freehand, Rectangle, Ellipse), and the area fills with your current color as soon as the selection completes. Color Fill works on a single layer, not on a group, and the setting persists until you turn it off.
- Fill Layer. From Layer Options, fill an entire layer with your active color. This is useful for solid backgrounds or for creating a color layer you'll mask later.
Use Color Drop for fast, outline-based fills. Use Selections for shapes without defined outlines, and Fill Layer for full-canvas color.
Using Color Drop in a Motion Design Workflow
Procreate is rarely the final stop for motion artists. A few habits make Color Drop output easier to use downstream.
- Separate by layer. Use the Reference layer method so line, flat color, and shading are independent. Keeping them on separate layers makes each element easier to animate, parent, or recolor downstream.
- Close shapes deliberately. Gaps cause stray fills, and they also make shapes harder to cut out and rig later.
- Name and organize layers before export. Color regions become puppet parts, mattes, or texture inputs.
- Use flat fills for color keys. Block in palettes and compositions quickly to explore options before committing to full rendering.
Where Styleframe Fits After Your Procreate Fills
Color Drop gets you flat, controlled artwork quickly. The next question is often how to move that artwork into motion or restyle it without redrawing everything. is one option to explore for that next step. Your Procreate files stay the source of truth, and any tool you add is a way to extend them into motion, not a replacement for your drawing or comp tools.
Quick Color Drop Checklist
- Close every gap in the outline before filling.
- Drag the color into the shape, hold, and watch for the blue threshold bar.
- Slide left for less fill and right for more, then lift to commit.
- Remember that the last threshold persists between fills.
- Use a Reference layer to keep fills separate from line art.
- Use Continue Filling for many regions in a row.
- Switch to Selections Color Fill or Recolor when outlines aren't clean.
FAQ
Why does Color Drop fill my whole canvas? The shape has a gap, so the color escapes. Close the outline.
Can I use Color Drop on a different layer than my line art? Yes. Set the line art layer as Reference in Layer Options, then fill on a separate layer. Automatic Selection is another route.
Does Procreate remember my threshold? Yes. It keeps the last setting you used, so adjust it again if a new fill behaves oddly.
Is there a faster way to fill many shapes? Use Continue Filling after your first Color Drop, then tap each region you want to fill.