How to Use Paint Bucket in Procreate Pocket
StyleFrame Team7 min read
To use the paint bucket in Procreate Pocket, drag the active color swatch from the top right corner of the screen and release it inside the area you want to fill. This feature is called ColorDrop. Before lifting your finger, pause and slide left or right to set the Threshold, which controls how far the fill spreads. After a drop, tap Continue Filling to fill more areas with single taps.
What the Paint Bucket Is Called in Procreate Pocket
Procreate has no tool labeled "Paint Bucket." The same job is done by ColorDrop, a flood fill you trigger by dragging color onto the canvas instead of selecting a tool from a toolbar. Artists coming from Photoshop, Clip Studio, or Animate often can't find a bucket icon and assume it's missing. It isn't, but it behaves differently from a tool you select and keep active.
According to the Procreate Pocket Handbook, the fill spreads outward from the drop point until it meets a boundary, such as an outline. That boundary logic matters for everything below, because most fill problems come from a boundary that isn't there.
Step-by-Step: Fill an Area With ColorDrop
- Pick your color. Tap the color circle in the top right to open the Colors panel. Choose a color with the Disc, Classic, Harmony, Value, or Palettes tab. For exact matches, the Value tab accepts hex codes.
- Select the target layer. The fill goes onto whichever layer is active. Check the Layers panel before dropping.
- Drag the active color onto the canvas. Press the color circle and drag it into the enclosed area you want to fill. Don't release yet.
- Hold briefly to set the Threshold. Keep your finger down. A Threshold percentage appears at the top of the screen. Slide left to fill less and right to fill more.
- Release to commit. Lifting your finger applies the fill. Procreate remembers your Threshold until you change it.
The Threshold is the part most beginners skip. If your fill floods the whole layer or leaves a halo of unfilled pixels along the edges, the Threshold is almost always the cause.
Fill Multiple Areas Faster With Continue Filling
Dragging the color from the corner for every shape is slow when you're flatting a drawing with dozens of regions. After your first ColorDrop, a Continue Filling option appears. Tap it, and each tap on the canvas fills that region with the current color. You can also tap and hold, then drag, to adjust the Threshold on the fly.
To leave Continue Filling mode, tap the checkmark at the top or switch to another tool such as Paint. If a stray tap fills something unexpectedly, undo it.
Fill Cleanly on a Separate Layer With a Reference Layer
The most common complaint about ColorDrop is that it floods an entire layer when you try to color under your linework. The reason is that ColorDrop reads the pixels of the layer you're filling, so if your lines sit on a different layer, there's no boundary to stop it.
The fix is a Reference layer:
- Put your line art on its own layer.
- Open the Layers panel and tap the line art layer to open its options.
- Tap Reference.
- Create a new layer underneath and select it.
- Use ColorDrop as usual. The fill now respects the line art but lands on the new layer.
This is the setup to use if you hand off flat color layers to a compositor. It keeps linework, flats, and later shading separate and editable. Note that only layers marked as Reference are read this way.
Other Ways to Fill in Procreate Pocket
ColorDrop covers most cases, but a few other options are worth knowing.
Selection with Color Fill
If you want a precise shape rather than a flood, make a selection and fill it. Procreate's Selection tool has a Color Fill option that fills any selection with your current color the moment you complete it. Turn it on, choose Automatic, Freehand, Rectangle, or Ellipse, and each selection fills as you finish it. Two cautions:
- Color Fill remembers its setting between sessions. If your selections suddenly start filling with color, switch it off.
- It works on a single layer, not a group.
Fill an entire layer
To cover a whole layer with one color, set your active color, open the layer's options in the Layers panel, and choose Fill Layer. This works for solid background plates or base layers you plan to mask later.
Recolor
Procreate's iPad documentation describes Recolor as an older fill method that you can restore through the QuickMenu, with a Flood slider to control spread. Its availability and menu location in Pocket may differ from the iPad version, so check your app's gesture settings before building a workflow around it.
Troubleshooting Common ColorDrop Problems
The whole layer fills. Lower the Threshold by sliding left while holding. If you're filling a different layer than your lines, set up a Reference layer as described above.
The fill leaks through the artwork. There's a gap in your outline. Users report that Procreate doesn't offer a gap-closing setting like some dedicated inking apps do, so zoom in and close the opening with a small brush stroke. Doing this on the line art layer solves it for every later fill.
A rim of the old color remains around edges. Antialiasing leaves semi-transparent pixels along lines. Raise the Threshold a little so the fill reaches into those edge pixels. If the fringe persists, you can also put a darker or matching fill layer underneath to hide it.
You can't fill a complex shape in one go. ColorDrop fills one contiguous region at a time. Users in Procreate's own idea forum have long asked for a Magic Wand-style selection tool for picking complex areas and inverting them. If you need that, use Selection with Automatic mode, or close the shape's gaps and fill it in sections.
The drag doesn't seem to work. Make sure you start by pressing the color circle itself, not the Colors panel, and that you aren't in a mode such as Continue Filling that changes how taps behave.
Why This Matters for Motion and VFX Work
You might wonder why a motion designer would care about a phone-based paint bucket. Procreate Pocket is useful for fast concept sketches, character color keys, and style frames made away from a workstation. Flat-color layers made with ColorDrop are especially handy because they produce clean regions that translate well into animation work.
A workable handoff looks like this:
- Build line art, flats, and shading on separate layers.
- Name layers with a consistent scheme so the file reads clearly when opened elsewhere.
- Export a layered file or individual PNGs, then import them into After Effects, Photoshop, or Blender as separate elements.
- Use the flat-color layers as mattes, track mattes, or color-keyed regions for isolating parts of a character.
Keeping flats separate from line art gives you control later. You can recolor a costume in After Effects with a Hue/Saturation adjustment on one layer without touching anything else.
Quick Reference
Final Tips
- Always check which layer is active before you drop color.
- Close gaps on the line art layer first, since that prevents leaks everywhere.
- Keep line art, flats, and shading on separate layers from the start.
- Turn off Color Fill in Selections when you're done with it.
- Zoom in before filling small details so you can see whether the fill reaches the edges.
ColorDrop feels different from a standard bucket tool, but once you understand the Threshold and Reference layer, it gives you quick, controllable flat color that hands off cleanly to the rest of your pipeline.