How to Use Opacity in Procreate
StyleFrame Team8 min read
In Procreate, you change opacity in three places: the lower slider in the sidebar for brush opacity, the layer's "N" menu in the Layers panel for layer opacity, and a two-finger tap on a layer followed by a slide on the canvas for a quick or selection-only adjustment. Only the slider inside the "N" menu is fully non-destructive, so use it when you may want to return to 100% later. The other methods commit the change to the pixels.
What Opacity Means in Procreate
Opacity describes how visible a pixel is. At 100% it is fully opaque, and at 50% it is half see-through. If you work in After Effects, the idea is the same as a layer's Opacity property, with one important difference: Procreate is a raster painting app, and not every opacity control in it behaves like a live, keyframeable property.
Procreate applies opacity at three levels:
- Brush opacity: how strong each stroke is as you paint.
- Layer opacity: how visible an entire layer is.
- Selection opacity: how visible a selected area of pixels is.
The key practical distinction is whether the change can be revisited. Layer opacity through the slider can be changed repeatedly. Selection opacity and the two-finger gesture bake the result into the layer.
How to Change Brush Opacity
Brush opacity controls how much paint each stroke lays down, which makes it useful for glazing, soft shading, and building up tone gradually.
- Select a brush.
- Find the two sliders on the sidebar. The lower one controls opacity.
- Drag it up to increase opacity and down to decrease it.
- Paint a test stroke and adjust until it looks right.
When Brush Opacity Seems Wrong
Many Procreate brushes respond to Apple Pencil pressure, so a brush can look too transparent even with the slider at maximum. If that happens, light pressure is probably reducing the effective opacity. Check the brush's pressure settings, or press harder as a quick test.
Also check what you are painting on. A layer set to a low opacity, or a layer clipped to a layer below, changes what you see. In a clipping mask, paint only appears where the base layer has pixels, so a stroke can seem to vanish when it is really being masked.
How to Change Layer Opacity (Non-Destructive)
This is the method most artists need, and the one that holds up best when you iterate.
- Open the Layers panel in the top right.
- Find the layer you want to adjust.
- Tap the small letter to the right of the layer name. It reads "N" by default, for Normal blend mode.
- Use the opacity slider at the top of the menu that opens. A percentage readout shows the current value.
The same menu holds the blend modes, so you can set opacity and blend mode in one place. Because the slider reflects the layer's current setting, you can reopen it at any point and push it back to 100%. Your underlying pixels are untouched.
Use this method when:
- You are building ghosted overlays, glows, or shadow layers you may need to rebalance.
- You are comparing alternatives and want to flip values quickly.
- You plan to export layered files and want each layer's level to stay adjustable.
The Two-Finger Gesture
The faster route is a gesture.
- Open the Layers panel.
- Tap the target layer with two fingers at once. An opacity readout appears at the top of the screen. Only one layer can be adjusted at a time.
- Slide left or right on the canvas. Left reduces opacity and right increases it.
- Lift your fingers or tap elsewhere to finish.
A common mistake is trying to drag the blue bar itself. It is a readout, not an interactive control. Slide anywhere on the canvas instead.
Why This Method Is Destructive
When you finish the gesture, Procreate commits the change. The new value becomes the layer's pixel data, so the lower opacity is the new "100%." You can undo immediately, but you cannot return later and reopen the same adjustment as you can with the "N" slider. If you drag a layer to 40% with the gesture and later want it back, you cannot simply slide it up to full strength.
That makes the gesture a good fit for quick, final decisions and a poor fit for anything you expect to revisit.
How to Change Selection Opacity
Sometimes you want to fade only part of a layer, such as one limb, one highlight, or one shape.
- Open the Selection tool and choose a method at the bottom, such as Automatic, Freehand, or Rectangle.
- Make your selection.
- Open the Layers panel.
- Tap the layer containing the paint with two fingers.
- Slide left on the canvas to reduce the opacity of the selected area, or right to increase it.
As with the gesture above, the change is applied when you exit, so treat it as a final action. A safer pattern for anything uncertain is to duplicate the layer first, apply the destructive change to the duplicate, and keep the original hidden. You can also move the selected content onto its own layer and use the layer opacity slider, which keeps the change reversible.
Using the QuickMenu for Opacity
If you adjust opacity often, you can add an opacity action to the QuickMenu and trigger it with a touch-and-hold on the canvas, then slide. There is a catch with the name. The QuickMenu action labeled "Layer Opacity" behaves like the opacity adjustment, not the layer slider. With an active selection, it changes only the selection. It is also destructive in the same way as the gesture.
If you want a one-touch shortcut, it is useful. Just don't treat it as a stand-in for the layer slider.
Troubleshooting Opacity Problems
A few issues come up repeatedly:
- The slider will not move. If you are dragging the blue bar after a two-finger tap, drag on the canvas instead. If the control still does not respond, restart the iPad fully, since a hard reboot is the usual first suggestion for odd gesture problems.
- You cannot find Opacity in the Adjustments menu. Older versions of the handbook describe Adjustments > Opacity, but current versions rely on the Layers panel and gestures. Use the "N" menu or the two-finger method.
- Opacity changes only part of the artwork. Check for an active selection. With a selection, opacity adjustments apply to the selected area only.
- A brush looks faded. Check the sidebar slider, the pressure curve, and the opacity of the layer you are painting on.
Bringing Procreate Opacity Into a Motion Pipeline
For animators and motion designers, Procreate often serves as a fast sketching and concept tool before work moves into After Effects, Premiere Pro, Blender, or Nuke. A few habits make the handoff cleaner.
Keep opacity adjustable for as long as possible. Use the layer slider for ghosts, glows, and overlays so you can rebalance later. If you apply destructive opacity changes, keep a duplicate of the original layer.
Separate elements by animation need. Anything you want to fade in After Effects should live on its own layer, at full opacity if possible, so you can keyframe its Opacity property there with proper easing. Procreate is the place to paint the element, and your compositor is the place to animate its visibility.
Test the export before committing. Layer opacity and blend modes may look different once a layered file is opened in another application. Export one test file, open it in your compositing app, and compare. If values differ, flatten the affected layers or adjust them in comp.
Use transparent PNGs for assets. For elements with soft edges, export with transparency rather than painting onto a colored background, so your alpha stays clean.
Where Styleframe Fits
Procreate opacity work often produces frames you want to push further: a loose sketch, a layered key pose, or a painted style reference. Styleframe is an AI video and motion tool built for artistic control, and its generation is driven by your own reference images, video clips, and keyframes rather than by a one-click black box.
In practice, you could finalize key poses in Procreate, flatten them with the opacity levels you settled on, and bring them into Styleframe as reference material. A painted frame can also serve as a style reference.
Procreate stays the place where you paint, and your compositor stays the place where you finish.
Quick Reference
When in doubt, use the "N" menu slider. It is slightly slower than the gesture, but it keeps your options open, which matters most once your artwork heads into a larger production pipeline.