How to Use Fill Tool in Procreate
StyleFrame Team7 min read
To fill an area in Procreate, drag the color from the Colors icon (top right) into a closed shape and release. This is ColorDrop, Procreate's paint bucket. Before you lift your Apple Pencil, hold still and slide left or right to adjust the ColorDrop Threshold, which controls how aggressively the fill spreads. If the fill floods the whole layer, the cause is almost always a threshold set too high or line art on a separate layer that isn't set as Reference.
The Fill Methods in Procreate
Procreate offers several ways to fill, each suited to a different job:
- ColorDrop with Continue Filling: the fastest way to flat-fill closed shapes.
- Recolor: a tap-to-fill mode you reach through QuickMenu.
- Selections → Color Fill: fills whatever you select the moment the selection completes.
- Fill Layer: floods an entire layer with the current color.
Most of the confusion around "the fill tool" comes from not knowing which of these you're using, so it helps to learn them as separate tools.
How to Use ColorDrop
ColorDrop is the primary fill method and the one you'll use most.
- Pick your color from the Colors icon in the top right.
- Drag the color from that icon into the area you want to fill. Keep your Apple Pencil or finger on the screen.
- Still holding, slide left or right to set the Threshold. A percentage appears at the top of the canvas, and the blue Threshold bar shows how far the fill will spread.
- Lift to commit the fill.
You can also drag a color from the floating color palette, which is handy when the fill color differs from your outline color.
ColorDrop only fills cleanly when the shape is closed. If there's a gap in the outline, the color escapes through it and floods the layer. If that happens, undo with a two-finger tap, close the gap, and try again.
Adjusting the Threshold
Procreate remembers the Threshold you last set, so a value that worked for one drawing can ruin the next. Two quick rules:
- Fill is leaking or covering everything: slide left to lower the percentage.
- Fill leaves untouched pixels near the edges: slide right in small increments.
Moving slowly gives you precise control, one percentage point at a time. This matters most with textured brushes. A grainy chalk-style outline has lighter patches and tiny gaps, so a low threshold can leave unfilled pockets along the edge. Raising the threshold closes some of them. Even then, expect some mismatch between a clean solid fill and a textured line. If you want crisp flats, draw your shape with a smooth, fully opaque brush.
Continue Filling for Multiple Areas
After a ColorDrop, tap Continue Filling to fill other regions with a simple tap, without dragging the color each time. Tap and hold, then drag, if you need to adjust the Threshold on a particular tap. To exit, tap the tick at the top or switch to another tool such as Paint.
On an iPad that supports Apple Pencil hover, you can hover the pencil tip over your current color in the top right and double-tap the side of the Pencil to activate Continue Filling with that color right away. It's a real time-saver on flat-color passes with dozens of regions.
Fill Under Line Art with a Reference Layer
Professional workflows almost always keep line art on one layer and flats on another. ColorDrop won't see your lines unless you tell it where they are.
- Open the Layers panel.
- Tap the thumbnail of your line art layer.
- Choose Reference in the Layer Options menu.
- Select your color layer, then ColorDrop into the shapes.
With Reference on, ColorDrop fills according to what's on the reference layer, regardless of which layer you're painting on. It respects those boundaries even when the Threshold is at zero.
The reverse problem matters too. If Reference is accidentally switched on for a blank layer, ColorDrop has no boundaries and floods everything. When a fill misbehaves, open the Layers panel and check which layers show the Reference label.
Recolor: The Tap-to-Fill Alternative
Recolor is a tap-based alternative to ColorDrop. It's accessed through QuickMenu, which is off by default.
To turn QuickMenu on, go to Actions → Prefs → Gesture Controls → QuickMenu and enable the gesture you want to use to invoke it. Then:
- Assign Recolor to one of the QuickMenu radial options.
- Tap it to enter the mode.
- Choose your color in the top right.
- Tap the areas you want to fill.
- Adjust the Flood slider to control how aggressively the fill spreads.
Some Procreate users also point to Recolor in the Adjustments menu as the dedicated fill option. If you can't find it in one place, check the other. If you like Recolor, putting it in your QuickMenu makes it a one-tap tool.
Selections → Color Fill
Color Fill works differently. Instead of flooding from a point, it fills a region you select.
- Tap Selections at the top.
- Choose a selection method from the tabs at the bottom (Automatic, Freehand, Rectangle, or Ellipse).
- Tap Color Fill so it's highlighted blue.
- Pick your color from the Colors icon.
- Make your selection. The fill is applied as soon as the selection completes.
This suits geometric shapes, backgrounds, and anything you'd rather outline than flood. Combine it with Feather to soften the edges, such as when framing artwork with a vignette-like shape.
Two cautions:
- Color Fill is remembered between sessions in Selections, so turn it off when you're done or you'll fill things by accident.
- It works on a single layer only. You can't Color Fill onto a group.
It also explains one common complaint. If you're following a ColorDrop tutorial and no Threshold slider appears, you may be in the selection tool's Color Fill rather than using ColorDrop.
Fill Layer
To flood an entire layer with one color:
- Choose your color.
- Open Layers and tap the layer twice to open Layer Options.
- Select Fill Layer.
Use this for solid backgrounds or to set up a base color you'll then paint over, mask, or clip other layers to.
Troubleshooting Fill Problems
If you still can't solve it, check your Threshold and whether any layer has Reference on, since those are the two most common causes of fill failures. Clean, closed linework is the most reliable fix for leaks.
Where Procreate Fills Fit in a Motion Pipeline
For motion designers and animators, Procreate is often where concept frames, style references, and hand-painted elements get made before the real production work happens in After Effects, Cinema 4D, Blender, or Nuke. Fast flats are useful at this stage. A set of clean color-blocked frames lets you test palettes, lighting moods, and compositions long before committing to animation.
A few habits keep those files pipeline-friendly:
- Put line art, flats, and shading on separate layers, using Reference so ColorDrop respects your lines.
- Keep fills on their own layers instead of painting into the line layer, so you can adjust color later without redrawing.
- Use solid, opaque lines on any layer you'll rely on for clean fills.
Using Your Filled Frames in Styleframe
Once you have flat-colored frames, you can use them as reference material for AI-assisted motion work in Styleframe. Compositing, color management, and finishing stay in the tools you already use.
Quick Reference
- Drag color from the Colors icon into a closed shape to use ColorDrop.
- Hold and slide before releasing to set the Threshold.
- Tap Continue Filling to fill more areas quickly.
- Set line art as Reference when filling on a separate layer.
- Use Selections → Color Fill for selected regions, Recolor for tap-to-fill, and Fill Layer for whole layers.
- When a fill goes wrong, check the Threshold, Reference layers, and gaps in your outline first.
Once those habits are in place, filling in Procreate is fast and predictable, and your flat frames are ready to feed into the rest of your motion workflow.