How to Use Fill in Procreate
StyleFrame Team7 min read
To fill an area in Procreate, drag your active color from the top-right Colors icon into a closed shape. This is ColorDrop, and it floods the area until it reaches an outline. Keep your finger or Apple Pencil down after dropping and slide left or right to change the Threshold, which controls how far the fill spreads. Other options include Continue Filling for repeated fills, Selections with Color Fill, and Fill Layer for covering a whole layer.
Method 1: ColorDrop
ColorDrop works like a paint bucket you drag into place.
- Pick your color in the Colors icon at the top right.
- Drag that color swatch onto the area you want to fill.
- Release to commit the fill.
The fill stops at the nearest boundary, so the shape needs to be closed. If your line has even a small gap, the color escapes and floods everything on the layer. If that happens, undo with a two-finger tap, close the gap, and try again.
You can also drag a color from an open color palette or a floating color panel. This is useful when you are filling with many colors that differ from your outline.
Adjusting the ColorDrop Threshold
Threshold decides how aggressively the fill spreads into edge pixels. It matters most with soft, anti-aliased, or textured lines.
- Drag the color into the area but do not lift.
- Wait until a blue bar and a percentage appear at the top of the canvas.
- Slide left to fill less, or right to fill more.
- Lift to commit.
Procreate remembers the last Threshold you used. If a new fill looks too aggressive or leaves halos around the line work, check that number before assuming something is broken.
For fine tuning, move slowly. Small increments of a percentage point at a time are usually enough to close the thin bright fringe that appears between a fill and an anti-aliased stroke.
Method 2: Continue Filling
If you are filling many regions, dragging the swatch each time is slow. After a ColorDrop, tap Continue Filling in the toolbar. You can then tap each area to fill it with the current color. Tap and hold, then drag, to adjust the Threshold for an individual fill.
To exit, tap the checkmark at the top or select another tool such as the Paint tool.
If your iPad and Apple Pencil support hover, you can hover over the active color swatch and double tap the Pencil's side to jump straight into Continue Filling. It saves a lot of steps on flat-color illustration or cel-style frames.
Method 3: Recolor via QuickMenu
Recolor is an older fill mode that Procreate brought back. It is not visible by default and is only available through QuickMenu.
To set it up:
- Open Actions → Prefs → Gesture Controls → QuickMenu.
- Choose how you want to invoke QuickMenu.
- Assign Recolor to one of the radial slots.
To use it, open QuickMenu, tap Recolor, choose a color, and tap areas to fill them. A Flood slider controls how aggressive the fill is, similar to Threshold in ColorDrop. Recolor is a matter of preference. Some artists find it more predictable than ColorDrop on certain line styles.
Method 4: Color Fill with Selections
Selections can fill an area the moment you complete the selection, which is useful when your shape has no outline or when you want a precise geometric fill.
- Tap Selections in the top toolbar.
- Choose a method from the tabs at the bottom: Automatic, Freehand, Rectangle, or Ellipse.
- Tap Color Fill so it is highlighted.
- Choose your color.
- Make the selection. The area fills with the color as soon as you finish.
A few practical notes:
- Automatic is good for picking out regions based on existing pixels.
- Freehand works for irregular shapes, such as quick masks or hand-cut forms.
- Rectangle and Ellipse are fast for backgrounds, vignettes, and basic shapes. Combine them with Feather to soften the edges.
- Color Fill stays on after you leave Selections. If your next selection fills unexpectedly, turn it off.
- Color Fill works on a single layer. It will not work if you have a group selected.
Method 5: Fill Layer
Fill Layer covers an entire layer with the current color. It is useful for solid backgrounds or flat color base layers.
- Choose your color.
- Open the Layers panel.
- Tap the layer twice to open Layer Options.
- Tap Fill Layer.
Use it on a new, empty layer so you can adjust or delete it later. If you fill the wrong layer, undo right away.
Why Your Fill Floods the Whole Canvas
The most common complaint is that the fill covers the entire page. These are the usual causes, in rough order of likelihood:
1. There is a gap in the line. Zoom in and check closely. Even a tiny break lets the fill escape. Close it with a small brush stroke and try again.
2. Your line art is on a different layer. ColorDrop reads the layer you are filling on. If the outline is on another layer and you are dropping color onto an empty layer, there is nothing to stop the fill. The fix is to set the line art layer as a Reference layer (tap the layer thumbnail and choose Reference). ColorDrop then follows the boundaries on the reference layer, even when you fill on another layer.
3. Reference is on the wrong layer. The reverse also happens. If Reference is active on an empty layer, ColorDrop sees no boundaries and floods. Open the Layers panel and look for the Reference label on layer thumbnails.
4. The Threshold is too high. Because Procreate remembers the last setting, an earlier aggressive fill can carry over. Hold after dropping and lower it.
5. You are using Selections Color Fill, not ColorDrop. Some users look for a Threshold slider that never appears because they are in Selections. Color Fill in Selections has no Threshold. Switch back to ColorDrop for Threshold control.
6. The brush is textured. Chalk, charcoal, and grainy brushes leave tiny holes and variable-opacity edges. The fill may leak or leave an uneven fringe. Raise the Threshold slowly, or draw outlines with a solid brush like Monoline and add texture afterward.
Keeping Fills Clean: Practical Tips
- Fill on a layer below the line art. This keeps color and line separate, so you can edit either without damaging the other.
- Use Reference for line art. Set your outline layer as Reference, create a new layer beneath it, and ColorDrop into that layer. This is the standard flat-color workflow.
- Slightly overfill. Fill a bit past the line so no thin gaps show, then let the line art sit on top.
- Turn off Color Fill when you are done so you do not fill by accident later.
- Keep shapes on separate layers if they will animate or be adjusted independently.
Using Procreate Fills in a Motion Pipeline
For motion designers and animators, Procreate is often a place to build characters, backgrounds, textures, and style frames before the work moves to After Effects, Nuke, or a 3D app. Clean fills make that handoff easier.
A few habits help:
- Name and organize layers by element (background, character base, shadow, line art) before exporting.
- Check edges at 100% and 200% zoom before export. Threshold fringing that looks fine on an iPad can show up as a visible halo once the art is scaled in a comp.
- Keep fills on transparent layers so you can composite, matte, and color-correct them in your usual tools.
Quick Reference
Final Notes
Fills in Procreate are quick once you know the three controls that matter: a closed shape, the right layer (or Reference), and the Threshold. When a fill misbehaves, check those in order. Then build your layers so that color, line, and effects stay separate. That discipline pays off most when the art leaves Procreate and enters a motion or compositing pipeline.