How to Use Fill Bucket in Procreate
StyleFrame Team7 min read
Procreate has no single bucket tool. Its fill bucket is ColorDrop: drag the color dot from the top right of the canvas into a closed shape, hold, and slide left or right to set the Threshold, then lift to commit. Tap Continue Filling to fill more areas with single taps. For other jobs, use Selections → Color Fill, Recolor from the QuickMenu, or Fill Layer to flood a whole layer.
The Quick Version
- Pick a color in the top right.
- Drag the color dot into the shape you want to fill and keep holding.
- Slide left or right to adjust the Threshold shown at the top of the canvas.
- Lift your Apple Pencil or finger to commit.
If the fill floods the entire layer instead of one shape, the Threshold is almost always too high, or another layer is set as the Reference layer. Both fixes are covered below.
How ColorDrop Works
ColorDrop works like a paint bucket you drag into place. Where a classic bucket tool is a button you select and then click, ColorDrop is a gesture.
Step-by-step
- Select the layer you want to fill.
- Tap the Colors icon in the top right and choose a color. The dot in the corner shows the current color.
- Drag from that dot into the area you want to fill. Don't lift yet.
- Keep holding. Procreate shows a blue Threshold percentage at the top of the interface.
- Slide left to fill less and right to fill more. Lift to commit.
Procreate remembers your Threshold until you change it, so once it's dialed in for a piece of line art, later fills behave the same way.
Continue Filling
After a ColorDrop, a Continue Filling option appears at the top. Tap it and every subsequent tap on the canvas fills with the current color. You can also tap, hold, and drag to adjust the Threshold on the fly.
To exit, tap the tick at the top or switch to another tool such as a brush.
If you use an Apple Pencil on an iPad that supports hover, you can hover over the current color dot and double tap the side of the Pencil to jump straight into Continue Filling with that color. This is a real time-saver when you're flatting dozens of shapes.
Understanding the Threshold
The Threshold decides how much of the neighboring color range Procreate treats as "the same area." Low values fill only pixels very close to the one you dropped on. High values spread into progressively different pixels, and at the extreme they flood the whole layer.
Practical guidance:
- Clean, solid line art: a moderate Threshold is usually enough to fill right up to the lines.
- Soft or textured edges: you may need a higher Threshold to reach the edge of the stroke. Pushing too far starts to leak.
- Flooding the whole layer: pull the slider back to the left. This is the most common beginner problem.
Because the Threshold is set while you're still holding, you can see the fill update live and stop at the moment it looks right.
Filling on a Separate Layer with a Reference Layer
Many artists keep line art on one layer and color on another. By default, ColorDrop reads the layer you're filling on, so a fill on an empty layer has nothing to detect and floods everything. The fix is a Reference layer:
- Open the Layers menu.
- Tap the thumbnail of your line art layer.
- In Layer Options, tap Reference.
- Select your empty color layer and use ColorDrop as usual.
Now ColorDrop fills according to the line art, but puts the color on the layer you've selected. This is the standard way to keep flats non-destructive and separate from ink.
When Reference causes problems
The same feature can cause confusion. If a different layer is still marked Reference, ColorDrop follows that layer's shapes instead of the one you're working on. If your fills behave strangely, open the Layers menu, look for the word "Reference" on any thumbnail, and toggle it off on layers you don't want driving the fill.
Other Ways to Fill in Procreate
ColorDrop isn't the only option. Depending on the task, one of these may be faster.
Selections → Color Fill
This method fills whatever you select the instant the selection completes.
- Tap Selections at the top.
- Choose a method from the bottom tabs (Automatic, Freehand, Rectangle, Ellipse).
- Tap Color Fill so it's highlighted blue.
- Pick your color in the top right.
- Make your selection. The color fills right away.
Color Fill stays on even after you leave and re-enter Selections, so turn it off when you're done. It also works only on a single layer, not a group. Combined with Feather, it's a quick way to produce soft-edged shapes, such as a vignette frame.
Recolor
Recolor is an older fill method that Procreate brought back. It's hidden unless QuickMenu is enabled.
- Go to Actions → Prefs → Gesture Controls → QuickMenu and turn on your preferred trigger.
- Set one of the QuickMenu radial options to Recolor.
- Open QuickMenu and tap Recolor to enter the mode.
- Choose a color and tap the areas to fill.
- Use the Flood slider to control how aggressive the fill is.
Recolor suits people who prefer a tap-to-fill workflow, and it's an alternative to ColorDrop plus Continue Filling.
Fill Layer
To flood an entire layer with one color, for a background or a solid base:
- Choose your color.
- Open Layers and tap your target layer twice to open Layer Options.
- Tap Fill Layer.
Troubleshooting Common Fill Problems
The fill covers the whole canvas. Lower the Threshold by holding after the flood and sliding left. Also check whether a different layer is set as Reference.
ColorDrop ignores my line art when I fill on another layer. Mark the line art layer as Reference, then select your color layer.
The fill leaks through gaps. Users on the Procreate forums note that ColorDrop has no dedicated gap-closing setting like some inking-focused apps do. Close the gap with a brush stroke on the line art layer, or lower the Threshold and fill in passes.
Edges look rough or leave a thin halo. Antialiased lines produce soft edge pixels that a low-Threshold fill can skip. Raise the Threshold slightly, or fill beneath the line art on a layer below it so the ink covers the seam.
ColorDrop won't work at all. Check that your shapes are actually closed, that you're on the intended layer, and that no stray Reference layer is active. Test with a finger as well as the Pencil to rule out a hardware issue.
Color Fill doesn't work on a group. Select an individual layer instead of the group.
A Clean Flatting Workflow
A reliable setup for character or illustration work:
- Ink on one layer and mark it Reference.
- Create a new layer underneath for flats.
- Use ColorDrop with Continue Filling, adjusting the Threshold once for the piece.
- Put shadows and highlights on clipped layers above the flats.
- Use Fill Layer on a separate layer for a solid background.
Keeping each element on its own layer matters for anyone who will hand the art off to an animation or compositing pipeline, since separate flats are much easier to isolate and recolor later.
Where Procreate Fills Fit in a Motion Pipeline
Many motion designers and animators use Procreate for what comes before the timeline: character designs, storyboard panels, texture elements, and style frames. A tidy flatted illustration, with ink, flats, and shading on separate layers, is a strong starting asset because it carries clear artistic intent.
This is where can sit beside Procreate, as a tool for taking finished artwork into motion work. Procreate remains where the artwork is drawn.
Clean, well-separated fills help here too. Flat shapes with crisp edges give a reference clear color and shape information to work from, and they are easier to work with later.
Quick Reference
Final Tips
- Set the Threshold once per piece and let Procreate remember it.
- Keep line art and flats on separate layers, with line art marked Reference.
- Turn Color Fill off after using it, since the setting persists.
- If a fill misbehaves, check Threshold first, then Reference, then whether the shape is closed.
Once ColorDrop becomes a habit, flatting turns from a chore into a fast first pass, leaving more time for the parts of the illustration that need your judgment.