How to Use Colorfill on Procreate
StyleFrame Team7 min read
Colorfill in Procreate isn't a single tool. It's a group of fill methods: ColorDrop (drag the active color from the top-right into a closed shape), Continue Filling (keep tapping to fill more areas), Selections → Color Fill, Fill Layer, and Recolor. For most flat-color work, drag the color dot into a closed shape, hold, and slide left or right to set the Threshold before you lift. The sections below cover each method, when to pick it, and how to fix the usual "it filled my whole canvas" problem.
Which Procreate fill method should you use?
If you're prepping assets for animation, the choice usually comes down to precision. ColorDrop is fastest, while Selections give you the most control over edges.
How to use ColorDrop
ColorDrop works like a paint bucket you physically drag onto the canvas.
- Select the layer you want to fill. Usually this is a layer beneath or alongside your line art.
- Pick your color from the Colors panel.
- Touch and hold the color dot in the top-right corner, then drag it into the area you want to fill.
- Keep your Apple Pencil or finger on the screen. A Threshold percentage appears at the top of the interface.
- Slide left to fill less, or right to fill more.
- Lift to commit the fill.
The Threshold is the setting people overlook. It controls how far the color spreads into pixels that differ from where you dropped it. A low value stays tight to the line. A high value pushes color through anti-aliased edges and soft strokes. If your line art has soft or textured edges, nudge the Threshold up slowly, a percentage point at a time, until the fringe is covered without leaking.
Continue Filling
After a ColorDrop, a Continue Filling option appears. Tap it, then tap other regions to fill them with the same color. You can also tap and hold to adjust the Threshold on each fill. Tap the checkmark or switch to a different tool such as Paint to exit.
If your iPad and Apple Pencil support hover, you can hover over the current color dot and double-tap the Pencil's side to start Continue Filling with that color. That makes it quick to block in a whole character with one palette entry at a time.
How to use Color Fill with Selections
Selections → Color Fill fills a region the moment you finish selecting it. This is useful when your shape doesn't have clean line art or when you want geometry-based fills like rectangles and ellipses.
- Tap Selections in the top toolbar.
- Choose a selection mode from the bottom tabs: Automatic, Freehand, Rectangle, or Ellipse.
- Tap Color Fill so it's highlighted blue.
- Choose a color from the Colors icon.
- Make your selection. The fill applies as soon as you complete it.
Two things to remember:
- The setting persists. Color Fill stays on when you leave and re-enter Selections. If you start getting unexpected fills later, check that it's off.
- It works on a single layer only. You can't Color Fill onto a group of layers, so select an individual layer first.
Pair this with Selections → Feather when you want a soft-edged fill, such as a vignette or a gradient-like glow behind artwork.
How to use Fill Layer
Fill Layer is the right tool when a whole layer needs to become one flat color, such as a solid background or a base layer you'll later mask.
- Pick your color in the Colors panel.
- Open Layers and tap the target layer twice to open Layer Options.
- Tap Fill Layer.
Everything on that layer becomes the active color, so use a fresh layer if you want to keep the original pixels.
How to use Recolor
Recolor is an older fill mode that Procreate brought back after users asked for it. It's only available through QuickMenu, which is off by default.
- Go to Actions → Prefs → Gesture Controls → QuickMenu and turn on your preferred trigger.
- Set one of the QuickMenu radial options to Recolor.
- Invoke QuickMenu and tap Recolor to enter the mode.
- Pick a color, then tap the areas you want to fill.
- Adjust the Flood slider to control how aggressive the fill is.
Flood is basically the same idea as the ColorDrop Threshold. If you already like ColorDrop, you probably don't need Recolor, but it's handy if you prefer tapping to dragging.
Cleaner fills with a Reference layer
A common workflow is to keep line art on one layer and color on another. For this to work, ColorDrop has to read the line art layer rather than the empty layer you're filling.
- Open Layer Options on your line art layer and turn on Reference.
- Create a new layer beneath it for color.
- Select the color layer and ColorDrop into your closed shapes.
The fill now respects your lines but lands on the separate layer, so you can edit, mask, or recolor it later without touching the drawing. That separation is what makes the artwork easy to rig or animate downstream.
Troubleshooting: when the fill covers the whole canvas
Most fill problems come from a short list of causes.
- Gaps in the line art. A single open gap lets the color escape and flood the screen. Undo, close the gap with a brush, and try again.
- Threshold at 100%. If it fills everything, hold the color over the shape without lifting, then drag left to lower the Threshold before you release.
- A stray Reference layer. If another layer, even one in a different group, is set as Reference, ColorDrop may sample it instead of what you expect. Check your layer stack and turn off Reference on layers you aren't using.
- Unmerged outline layers. If your outlines are spread across several layers and only some are referenced, the fill can leak. Merge the outline layers, or make sure all of them are referenced.
- Textured brushes. Grainy line art has tiny gaps, so the fill leaves a halo between color and line. Raise the Threshold slightly, but expect some mismatch between a solid fill and textured strokes. Another option is to paint the fill layer under the lines and let the texture overlap.
- A drag that does nothing. If you can't pick up the color dot, force-quit and reopen Procreate. Some users have reported intermittent failures that clear after a restart.
Taking Procreate fills into a motion pipeline
If you're a motion designer or animator, Procreate is often where assets start rather than where they end. A few habits make the handoff smoother:
- Keep fills on separate layers. Line, flat color, shadow, and highlight on separate layers means you can bring them into After Effects as a layered PSD and animate or adjust each independently.
- Fill slightly past the line. A small overlap under the line art avoids hairline gaps when layers are scaled or moved.
- Name and organize layers before exporting. It saves time once you're building comps in After Effects or Nuke.
- Work at the final resolution. Fills made on a small canvas will soften when scaled up for video delivery.
Once your flat-color frames exist, is one option for extending them in motion while you keep control of the look. Your compositing workflow stays as it is.
Quick recap
- Use ColorDrop for fast fills, and adjust the Threshold before lifting your Pencil.
- Use Continue Filling to fill multiple regions without re-dragging.
- Use Selections → Color Fill when you want a fill applied at the moment you select, and remember to switch it off afterward.
- Use Fill Layer to flood an entire layer.
- Set line art to Reference and fill on a separate layer for clean, editable color.
- If a fill floods the canvas, check for line gaps, Threshold, and stray Reference layers first.
Once these habits are in place, filling in Procreate gets much faster, and your layered files are in better shape for animation and compositing.