How to Use Bucket Tool in Procreate Pocket
StyleFrame Team7 min read
To use the bucket tool in Procreate Pocket, drag your Active Color (the color swatch at the top right of the Colors panel) onto the canvas and release it inside the area you want to fill. This gesture is called ColorDrop, and it is Pocket's version of a paint bucket. Before releasing, keep holding and slide left or right to set the fill threshold, which controls how far the color spreads past similar pixels. After a drop, tap Continue Filling to flood-fill more areas with single taps.
What the bucket tool is called in Procreate Pocket
The fill function is ColorDrop, and it is invoked from the color system by dragging the Active Color onto the canvas. The Pocket handbook describes it this way: drag the Active Color into any area of your artwork, release it, and the color spreads outward until it hits a boundary such as an outline or a change in color.
That design matters if you're coming from other apps where the fill tool is a selectable mode. In Pocket, the "tool" is a gesture you perform with your current color, so you must pick the color first.
Step-by-step: filling an area with ColorDrop
- Choose your color. Open the Colors panel and pick a color using the Color Disc, Classic, Harmony, Value, or Palettes tab. The Value tab gives you hex input, which helps when you need to match brand or storyboard colors precisely.
- Locate the Active Color. Drag the swipe handle at the top of the Colors panel upward to expand it. The Active Color appears in the top right. Tapping it opens the Colors interface. On the canvas, the same swatch sits in the top right of the interface.
- Select the right layer. Check the Layers panel before you drop so the fill lands on the layer you intend.
- Drag the color onto the area. Press the swatch, drag it into the enclosed region, and keep your finger down.
- Set the threshold. While still holding, slide left or right. Left fills less, right fills more. A percentage readout at the top of the screen shows the current threshold value.
- Release to commit. Lift your finger to apply the fill.
If the result is wrong, undo and drop again with a different threshold. Because the threshold is set per drop, you can tune it for each region instead of committing to one global tolerance.
Understanding the threshold
The threshold behaves like the tolerance setting in a magic wand or fill tool in other apps. A low value fills only pixels very close to the one you dropped on. A high value fills a wider range of similar tones.
Practical guidance:
- Clean, hard-edged line art: a low-to-moderate threshold is usually enough, because the boundary is high contrast.
- Anti-aliased or soft lines: raise the threshold slightly so the fill reaches the edge of the line instead of leaving a pale halo between color and ink.
- Textured or painted regions: a higher threshold helps the fill cross subtle variation, but it can also bleed into neighboring shapes, so watch the preview as you drag.
If you push the threshold too far, the fill spills across boundaries. If it's too low, you get speckled, incomplete coverage. Adjust in small increments rather than sweeping all the way across.
Continue Filling for fast flat-color passes
After a ColorDrop, Pocket offers a Continue Filling option. Tap it and you can fill additional areas with single taps, using the same color. Tap and hold, then drag, to change the threshold for a specific tap. To exit, tap the checkmark at the top or switch to another tool such as Paint.
This is the quickest way to block in flat colors across a cleaned-up drawing. You pick a color, tap through every region that needs it, then change color and repeat. On a phone screen, that's far less fiddly than repeatedly dragging the swatch.
Other ways to fill when ColorDrop isn't enough
ColorDrop is the closest match to a paint bucket, but Procreate documents several other fill methods. The Help Center describes them for the iPad version, and Pocket may have similar functionality, though menu placement can differ. Confirm each in your own build before relying on it in a production workflow.
Recolor
Recolor is an older fill mode that's accessible through the QuickMenu, which is off by default. You enable it under the Actions menu in Prefs, in Gesture Controls. Then you assign Recolor to one of the QuickMenu radial options. Once active, you choose a color, tap areas to fill them, and adjust a Flood slider to control how aggressive the fill is. Some artists prefer it because it behaves like a traditional tap-to-fill tool.
Selections with Color Fill
In the Selections tool, the Color Fill toggle fills any area you select with your current color the moment the selection completes. It works with Automatic, Freehand, Rectangle, and Ellipse selection modes. Two cautions from the documentation: Color Fill only works on a single layer, not a group, and the setting persists after you leave Selections, so turn it off when you're done. Otherwise, a later selection will unexpectedly fill with color. This also causes problems when copying and pasting, which is why guides tell you to disable it first.
Fill Layer
If you want to fill an entire layer with the current color, use the Layer Options menu and choose Fill Layer. This is useful for flat background plates or for creating a solid color layer you'll later mask or clip other layers to.
Fixing common fill problems
The fill leaks across the whole canvas. There is a gap in your line art. Zoom in and close it with a small brush stroke on the line layer, or lower the threshold so the fill respects the edge. Gaps of a single pixel are easy to miss at normal zoom.
There's a light fringe around filled shapes. This comes from anti-aliased edges that the fill didn't fully reach. Raise the threshold slightly. Alternatively, put the fill on a separate layer beneath your line art so the ink covers the seam.
The fill ignores my lines. If the line art is on a different layer from the one you're filling on, ColorDrop may not see it. Try keeping lines and colors on the same layer, or close any gaps and adjust the threshold.
I want to recolor later. Fill on a dedicated color layer rather than flattening everything, so you can change colors without disturbing your line art.
A layered setup that works well for animation assets
If your Pocket artwork is headed into a motion pipeline, set it up the way you'd prep a layered Photoshop file for After Effects:
- Put line art on its own layer.
- Fill flat colors on a separate layer below the lines.
- Keep shadows, highlights, and textures on their own layers.
- Name layers clearly so they're easy to find later.
Then export your layers or a PNG with transparency so you can bring individual pieces into After Effects, Nuke, or Blender. Filling with ColorDrop on a dedicated layer makes it far easier to build mattes, adjust hues in post, or swap a color across a scene.
Where Procreate Pocket sketches meet a professional video pipeline
Procreate Pocket is a good place to rough out character designs, style frames, and flat-color boards, especially away from your desk. Moving those pieces into finished motion is a different job, and that's where can fit.
None of this replaces careful fills in Pocket. The cleaner and more deliberate your color blocking, the better the reference material you hand to any downstream tool.
Quick reference
- Bucket tool equivalent: ColorDrop, dragged from the Active Color swatch.
- Set threshold: hold after dropping and slide left (less) or right (more).
- Fill multiple areas: tap Continue Filling after a drop.
- Alternatives: Recolor via QuickMenu, Selections with Color Fill, and Fill Layer.
- Leaks and fringes: close line gaps, adjust threshold, and fill on a separate layer under your lines.
- Before exporting: keep fills, lines, and effects on separate named layers for easier compositing.
Once the ColorDrop gesture is in your muscle memory, flat-color work in Pocket becomes fast enough to use for quick style frames, animatics, and asset prep you can carry straight into your motion workflow.