How to Use Blend Modes in Procreate
StyleFrame Team7 min read
To use blend modes in Procreate, open the Layers panel, tap the letter N on the layer you want to change, and pick a mode from the scrolling list. Each mode previews live as you scroll, and the Opacity slider in the same menu lets you fine-tune the result. Multiply darkens for shadows, Screen and Add lighten for glows, Overlay and Soft Light add contrast, and Color or Hue recolors without redrawing.
How to Change a Blend Mode in Procreate
The workflow takes a few seconds once you know where it lives:
- Tap the double-rectangle Layers icon in the top right of the interface.
- Look at the right edge of any layer. The letter shown is the active blend mode. New layers sit on N, for Normal.
- Tap the letter to open the Blend Modes menu. It has two parts: the mode name and an Opacity slider.
- Tap the mode name to open the scrolling list. Each mode applies to the layer as you scroll, so you can audition options without committing.
- Tap anywhere outside the list to close it, then adjust Opacity to taste.
Two details save time. First, the Opacity slider affects the entire layer and ignores any active selection. Second, you can two-finger-tap a layer to bring up a quick opacity control, then slide left or right across the canvas.
Because a blend mode depends on both the layer it sits on and the layers beneath it, the same mode can look completely different from one painting to the next. Always judge a mode against your actual artwork, not against a tutorial screenshot.
How Blend Modes Work
A blend mode is a rule for combining the pixel values of a top layer with those below it. Normal simply covers what's underneath. Every other mode runs a calculation that can darken, lighten, add contrast, compare, or shift color.
If you work in After Effects, Photoshop, or Nuke, many of these names will likely be familiar. Procreate groups its modes by intent rather than alphabetically. Procreate lists 26 modes, which fall into six groups: Normal, Darken, Lighten, Contrast, Difference, and Color. Knowing the group tells you what to expect before you try anything.
The Darken Group
These modes sit at the top of the list and push values down.
- Multiply multiplies the base by the blend color. The result is darker and richer, and underlying texture still shows through. This is the workhorse for shadows, shading, and laying paper grain over line art.
- Shade is the mode that older projects using Darken were switched to. Since Procreate 5.4, this keeps Procreate's Darken behaving more like it does in other software. If you move files between apps and notice a mismatch on this mode, that history is why.
- Color Burn raises contrast between base and blend, boosting mid-tone saturation and cutting highlights. It usually goes darker than Multiply.
- Linear Burn drops brightness based on the blend value. It is darker than Multiply but less saturated than Color Burn, and it holds contrast in dark colors.
- Darker Color compares a composite of the RGB channels instead of each channel separately, then keeps the darker result.
The Lighten Group
These mirror the darkening modes.
- Lighten keeps the lighter of the two values.
- Screen inverts, multiplies, and inverts again, so you only ever get lighter results. It is the standard choice for glows, light leaks, and soft highlights.
- Color Dodge brightens the base to reflect the blend color. It gets intense quickly, so keep opacity low.
- Add stacks the blend value onto the base for a hot, burning light effect.
- Lighter Color is the composite-channel counterpart to Lighten.
The Contrast Group
Overlay and its relatives act on both ends of the tonal range at once. Overlay behaves like a Multiply and Screen blend: dark areas get darker, light areas get lighter, and the result is punchy and vibrant. Soft Light does the same more gently, which makes it better for subtle dodging, burning, and tinting. The harder variants push further and are easy to overcook, so treat opacity as part of the choice rather than an afterthought.
The Difference and Color Groups
The Difference group compares layers and inverts based on the gap between them. It is less useful for painting and more useful for diagnostics, such as checking whether two versions of an image really match.
The Color group, including Hue, Saturation, Color, and Luminosity, lets you recolor artwork without repainting. Put a flat color on a layer set to Color and the underlying values are preserved while the hue changes. Combined with the Opacity slider, it gives you flexible tinting across a whole piece.
Practical Recipes
Shadows. Create a layer above your base colors, set it to Multiply, and paint with a desaturated cool color. Lower opacity until the shading sits naturally. Because Multiply preserves underlying texture, brush detail survives.
Glow and rim light. Add a new layer, set it to Screen or Add, and paint with a saturated warm color. Screen is more forgiving. Add and Color Dodge are better when you want a hotter, blown-out look.
Paper and grain texture. Place a scanned or generated texture above your illustration and set it to Multiply to make the artwork look like it sits in the paper. For a lighter touch, try Overlay or Soft Light at low opacity.
Color grading pass. On top of everything, add a layer set to Color or Soft Light and fill with a gradient. Adjust opacity to push the palette toward a mood without touching the original layers.
Safe experimentation. Duplicate a layer before testing modes so the original stays intact. Procreate's own guidance, and nearly every tutorial, comes back to the same advice: experiment, since the best result depends on your artwork.
Procreate Blend Modes vs. Your After Effects Habits
If you come from a compositing background, a few translation notes help:
- Many of the modes, such as Multiply, Screen, Overlay, Soft Light, Add, Color Dodge, and the Hue/Saturation/Color/Luminosity set, also appear in other software. The names will likely feel familiar, but check how each behaves in your own tools.
- Treat Darken carefully. Check the Shade versus Darken naming if you're moving files between apps.
- Color management can change how a mode looks. If your After Effects project blends in linear light, the same mode applied to the same pixels can look different from what you saw on the iPad. Always evaluate the final look in your comp rather than assuming a one-to-one match.
- If you bring a layered painted pass into After Effects or Nuke, verify that each layer's blend mode survived the trip, and rebuild any that didn't, so you aren't relying on a flattened guess.
A sensible split: use Procreate blend modes for the painterly decisions (hand-painted light, texture, tint) and keep final grading and compositing decisions in your compositor, where you can animate and revise them non-destructively.
Common Mistakes to Avoid
- Using full opacity by default. Many modes look best at reduced opacity. Dial back before you decide a mode doesn't work.
- Painting on the wrong layer. A blend mode applies to the whole layer. If you want it to affect only certain shapes, paint those shapes on their own layer.
- Forgetting the layers underneath. If a mode looks wrong, check what's below it. The result always depends on both layers.
- Stacking too many modes. Two or three well-chosen blend layers beat ten fighting each other. Name and group them so you can revise later.
- Ignoring naming differences. Shade, Darken, and Darker Color are not interchangeable.
Quick Reference
Procreate makes it easy to build good habits with blend modes: tap the N, scroll to preview, adjust opacity, and keep the original layers intact. Learn the six groups, and you can predict what a mode will do before you try it. That makes the painted frames you bring into After Effects, Nuke, or an AI-assisted motion workflow far more deliberate.