How to Use Adonit Pixel with Procreate
StyleFrame Team6 min read
To use the Adonit Pixel with Procreate, hold the button nearest the tip until the green light appears, then open Procreate's stylus settings, choose Adonit as a third-party stylus, and touch the tip to the on-screen pairing circle. Once it's paired, adjust Procreate's pressure curve until light strokes stay thin and hard strokes ramp up smoothly. Most problems come from pairing, Bluetooth conflicts, or a pressure curve that doesn't match the stylus.
Check compatibility before you pair
The Pixel is a Bluetooth stylus, not a passive one. It works like a finger on any capacitive screen, but pressure sensitivity, palm rejection, and the shortcut buttons need an iOS device with Bluetooth 4.0 and an app that supports it. Adonit lists 2048 pressure levels and a 1.9 mm fine-point tip.
Adonit's published compatibility list is older hardware: iPad mini through iPad mini 4, iPad Air, iPad Air 2, and the 2017 iPad (5th generation), plus several iPhones. Before buying or troubleshooting, check two things:
- Your iPad model against Adonit's list. If it isn't there, expect inconsistent behavior.
- The Procreate version your iPad can run. Newer Procreate builds may not support some older iPads. If you're on an older iPad, your Procreate version may have a different menu layout.
Adonit also sells the Pixel Pro, aimed at iPad Pro. The pairing logic is the same, but confirm compatibility for your specific model.
Step-by-step: pair the Pixel with Procreate
- Charge it. Adonit lists about one hour to charge and about 14 hours of use. Charge it before troubleshooting anything else.
- Power it on. Hold the black button closest to the tip until a green light brightens and then goes out. The grip sensor can also wake the stylus when you pick it up.
- Disconnect an Apple Pencil, if you have one. Adonit warns that a connected Apple Pencil can interfere with the Pixel. Remove it in the iPad's Bluetooth settings before pairing.
- Free a Bluetooth slot. Some iPads and iPhones can't hold more than four paired Bluetooth devices. If you're at the limit, go to Bluetooth settings, choose a device you don't need, and tap "Forget this device."
- Open Procreate's stylus settings. Procreate has reorganized its menus over the years. Older instructions mention a "Devices" tab, but some versions only show an option to add a third-party stylus. If the layout differs from a tutorial, the current Procreate Handbook shows where the setting lives in your version.
- Select Adonit and pair. With the stylus on, touch the tip to the on-screen circle when prompted. Pairing happens per app, so you repeat it in every app that supports the Pixel. Unlike an Apple Pencil, it won't carry across your drawing apps.
- Test on a blank canvas. Draw a slow light stroke, a medium stroke, and a hard stroke. You should see a clear progression in width or opacity, depending on the brush.
Tune the pressure curve
Most "the Pixel feels wrong" complaints are pressure curve problems. If strokes look gray, thin, or inconsistent, don't assume the hardware is faulty. Adjust the curve first.
Procreate's pressure curve is a graph that maps how hard you press to how the brush responds. Keep these rules in mind:
- A flatter or lower curve needs more pressure for heavier strokes. It suits a heavy hand and gives more control in the light range.
- A steeper or higher curve responds faster, so thick strokes arrive sooner. It suits a light touch.
- Change one thing at a time. Adjust the curve a little, draw the same three test strokes, and compare.
Test with a brush you actually use for production work, such as a linework inker or a textured shader. Pressure-sensitive brushes expose a bad curve faster than a basic round brush. Procreate's Handbook includes example curves, and its community forums have screenshots from artists using similar styluses. Treat those as starting points, since your hand pressure and your iPad model will differ.
Fix the most common Pixel problems in Procreate
Lines that thicken and won't thin out
Some users report strokes that keep getting thicker under steady light pressure, as if they were pressing at maximum, and then end abruptly when the tip lifts. Procreate staff have traced this kind of behavior, along with wavy lines, to how fine-point styluses interact with the screen. The Pixel generates a field at the tip that the display reads as touch input. On older iPads that were never designed for styluses, the screen can misread that signal.
What to try:
- Redraw the same stroke on a different part of the screen. Wavy lines are often most noticeable on diagonals.
- Zoom out or reposition the canvas, then test again. Some users find this clears a "stuck" wavy state.
- Test the same stylus in another app. If it behaves in a different drawing app, the cause is more likely Procreate's settings, the pairing, or the curve than a dead stylus.
- Record a short phone video of the problem. If you contact Procreate support, they'll ask for one.
Strokes turn gray or look weak
If a Pixel that worked before now draws pale, thin, or gray strokes, check the following in order:
- Replace or reseat the tip. A worn or loose tip changes how the screen reads contact.
- Hard reboot the iPad.
- Re-pair the stylus in Procreate.
- Reset or adjust the pressure curve.
It won't pair at all
If tapping the pairing circle does nothing, confirm the stylus is on, charged, and not competing with an Apple Pencil. Check the four-device Bluetooth limit. Make sure Procreate and iPadOS are updated to versions that your device supports. If you still can't pair, note your exact Procreate version, iPadOS version, and iPad model number, because support will ask for all three.
Set up Procreate for motion work
If your Procreate sketches are headed to After Effects, Premiere Pro, or a 3D package, a few habits save time later:
- Create the canvas at your delivery aspect ratio. For a 16:9 board, work at the final ratio, not a square, so nothing gets cropped in the comp.
- Work larger than you think. Older iPads may struggle with complex, high-resolution files. For an older Pixel-compatible iPad, you may need to split complex frames into separate files.
- Name and group layers. Separate line art, flats, shadows, and texture. If you'll be animating pieces in After Effects, export layers as separate PNGs with transparency.
- Keep a flattened reference. Export a full-resolution PNG of the composite alongside layered files so you have a locked look to match.
- Use consistent frame naming if you're drawing frame-by-frame, with zero-padded numbers, so image sequences import in the right order.
The Pixel is a good fit for this kind of work: boarding, rough animation passes, hand-drawn textures, and style frames. For finished, high-pressure illustration on a current iPad, an Apple Pencil-compatible stylus may serve you better, but for sketching and linework on supported devices, the Pixel does the job.
Quick checklist
- Pixel charged and powered on (green light).
- Apple Pencil disconnected from iPad Bluetooth.
- Fewer than four paired Bluetooth devices if pairing fails.
- Paired inside Procreate's stylus settings, not just iPad Bluetooth settings.
- Pressure curve tested with your real brushes.
- Tip checked, iPad rebooted, and Procreate updated to a version your device supports.
- Canvas set to the final aspect ratio, with exports named for easy import.
If those basics are in place and the Pixel still misbehaves, test it in another supported app to isolate whether the problem is the stylus, the iPad, or Procreate's configuration. That test tells you whether to adjust settings, replace the tip, or move to newer hardware.