How to U Se the Bucket Tool Procreate
StyleFrame Team7 min read
Procreate doesn't have a bucket button in its toolbar. Its paint bucket is called ColorDrop: drag the color dot from the top-right corner onto a closed area of your canvas, and keep your Apple Pencil or finger down to set how far the fill spreads. Lift to commit the fill, then tap Continue Filling to fill more areas without dragging the color again.
Where the Bucket Tool Is in Procreate
Artists coming from Photoshop, Clip Studio, or After Effects' own paint tools often look for a bucket icon and give up. Procreate's fill is built into the color picker. The color swatch in the top-right corner is the "bucket," and you drag its contents onto the canvas.
ColorDrop fills the region you drop onto, based on the pixels of the active layer, up to a threshold you control. It's a drag gesture rather than a tap, which makes it feel different from other apps, but the logic is the same as a standard flood fill.
How to Use ColorDrop, Step by Step
- Pick your color. Tap the Colors icon in the top right and choose a swatch, or sample one from the canvas.
- Select the layer you want to fill. By default, ColorDrop reads and fills the active layer (see the Reference Layer section below to change that).
- Drag the color dot into the area. Press the Colors icon, drag it into the shape you want to fill, and keep holding. The color floods in immediately.
- Adjust the threshold. Without lifting, pause, then slide left or right. The Threshold percentage appears at the top of the screen. Left fills less, right fills more.
- Lift to commit. When the fill reaches the edge you want, lift your Pencil or finger.
Procreate remembers your last threshold until you change it, so you don't need to reset it for every drop.
Understanding the Threshold
Threshold decides how different a neighboring pixel can be from where you dropped before the fill stops. A low value fills only pixels very close to the one you hit. A high value spreads across more varied pixels, and at the extreme it covers the whole layer.
Practical guidelines:
- Clean, hard-edged line art: a moderate threshold usually works well.
- Antialiased or soft edges: raise the threshold a little so the fill reaches into the semi-transparent edge pixels. Otherwise you can get a light halo between the fill and the line.
- Textured or painted areas: expect uneven results. Lower thresholds will leave speckles, and higher ones will spill. You may be better off using a selection (covered below).
If ColorDrop floods your entire layer, the threshold is almost always set too high. Drop again, pause, and pull the slider back to the left.
Filling Multiple Areas with Continue Filling
After a ColorDrop, a Continue Filling option appears. Tap it, and you can tap any other area to fill it with the same color, with no repeated trips to the top-right corner. You can also tap, hold, and drag to adjust the threshold on any individual fill.
To exit, tap the tick at the top or switch to another tool such as Paint.
If you're using an iPad with Pencil hover support, there's a shortcut: hover over the current color in the top right and double-tap the side of the Pencil to start Continue Filling with that color immediately. This matters if you're flatting a whole character or a set of shapes in one color.
Filling Under Line Art with a Reference Layer
A common complaint from new users is that ColorDrop only works when the fill and the line art are on the same layer. If you try to fill on a separate layer, the fill covers the whole layer, because that layer is empty and there are no edges to stop it.
The fix is Reference:
- Open the Layers panel.
- Tap the thumbnail of your line art layer to open Layer Options.
- Tap Reference.
- Select a new, empty layer below the line art.
- Use ColorDrop as usual.
Now ColorDrop reads its boundaries from the reference layer but paints onto the layer you're working on. This is the standard way to build a flat-color layer under ink lines, and it keeps your line art untouched and editable.
Other Ways to Fill in Procreate
ColorDrop isn't the only option. Depending on the job, one of these may be faster.
Recolor
Recolor is an older fill method that Procreate brought back. It's hidden behind QuickMenu, which is off by default.
- Go to Actions → Prefs → Gesture Controls → QuickMenu and turn on a method of invoking it.
- Assign Recolor to one of the QuickMenu radial slots.
- Open QuickMenu and tap Recolor.
- Choose your color, then tap the areas to fill.
- Use the Flood slider to control how aggressive the fill is.
Some artists prefer Recolor because it behaves like a conventional tap-to-fill bucket.
Selections with Color Fill
If you want to fill a shape you define yourself:
- Tap Selections at the top.
- Choose a method: Automatic, Freehand, Rectangle, or Ellipse.
- Turn on Color Fill (it's highlighted blue when active).
- Pick your color.
- Make the selection. It fills as soon as you finish.
With Automatic selection, the area you select is filled in one move. Color Fill works on a single layer only, not on a group, and it stays enabled even after you leave and return to Selections, so switch it off when you're done or you'll fill things by accident.
Fill Layer
To fill an entire layer with a color, select the color, open Layers, tap the layer twice to open Layer Options, and choose Fill Layer. This is useful for solid backgrounds or base layers you'll mask or clip other layers to.
Troubleshooting Common Fill Problems
The fill covers the whole canvas. Lower the threshold. If you're filling on a different layer from your line art, set the line art as a Reference layer.
The color leaks outside the shape. There's probably a gap in your line. Zoom in and close it with a small brush stroke. Some users point out that Procreate has no dedicated gap-closing setting in its fill, so checking your outlines first saves time.
A thin halo or fringe remains along the edges. Raise the threshold slightly so the fill covers antialiased edge pixels. Alternatively, fill on a layer below the line art so the lines overlap the fill.
Color Fill won't work. Check that you're on a single layer, not a group.
You only wanted to fill an irregular exterior region. ColorDrop fills one enclosed area at a time. For complex exterior shapes, try Selections with Color Fill instead.
What Procreate's Fill Can't Do
It's worth being clear about the limits, since professionals will hit them quickly. ColorDrop is strong for illustration and flatting, but long-time users of other software often ask for a true magic wand with grow, shrink, and invert controls, and for a fill that remembers its settings across repeated clicks. Continue Filling covers part of that. For high-volume inking or production flatting with strict, aliased edges, a dedicated tool like Clip Studio may suit you better.
For motion work, that's rarely a dealbreaker. Many designers and animators use Procreate for look development, storyboard frames, texture studies, and key art, not for frame-by-frame production.
Using Procreate Fills in a Motion Pipeline
If you're an After Effects, Nuke, or Cinema 4D artist, a Procreate file is usually an early step: a styleframe, a character design, a color script. Clean fills pay off downstream.
- Keep fills on separate layers (using the Reference method) so you can export layered files and rebuild them in After Effects with each color region as its own element.
- Name your layers before export. It's tedious to fix later.
- Flatten only copies. Keep the layered master for revisions.
Quick Reference
Final Tips
Start with ColorDrop and a Reference layer, since that combination solves most fill problems. Watch the threshold, close gaps before filling, and use Selections when a shape isn't neatly enclosed. Once those habits are in place, filling in Procreate becomes a quick, almost automatic part of building frames you can carry into your motion pipeline.