How to Turn Picture Into Drawing Procreate
StyleFrame Team7 min read
To turn a picture into a drawing in Procreate, insert the photo, duplicate it, desaturate the copy, duplicate again, set the top layer's blend mode to Divide, and apply Gaussian Blur until pencil-style lines appear. Procreate has no one-tap line art feature, so this is a layer-and-blend workaround. For a hand-drawn look, trace over the photo on a new layer at reduced opacity. The result is a raster image, so the next question for motion work is how to get it into your animation pipeline.
Method 1: Divide + Gaussian Blur (fastest line art)
This is the most common approach. It works because dividing a grayscale image by a blurred copy of itself leaves white everywhere except at edges, which become dark lines.
- Import the photo. Tap Actions (the wrench), choose Add, then Insert a photo. Fit it to the canvas.
- Duplicate the layer. Swipe left on the photo layer and tap Duplicate. Hide the bottom layer so you keep the original untouched.
- Desaturate the copy. Open Adjustments (the wand), choose Hue, Saturation, Brightness, and drag saturation to zero. You can nudge brightness if the image is very dark or very light.
- Duplicate the grayscale layer.
- Set the blend mode to Divide. Tap the "N" on the top layer's thumbnail and choose Divide. The canvas will look blank or white. That's expected.
- Apply Gaussian Blur. Go to Adjustments, choose Gaussian Blur, and drag across the screen. Lines appear as you increase the blur. Values from about 5% to 13% are typical, depending on resolution and how much detail you want.
- Merge down. Tap the top layer and choose Merge Down to combine the two grayscale layers.
- Tighten with Curves. Open Adjustments, then Curves. Pull the bottom-left point to the right to darken lines and clear paper-gray. Pull the top point slightly left, but not too far, or you'll invert the image.
Low blur gives fine, delicate lines. Higher blur gives bolder, sketchier strokes and loses small detail. Run through a few values before you commit.
Method 2: Invert + Color Dodge
This is an older variant that produces a similar result with a different layer stack:
- Insert the photo and duplicate it.
- Desaturate the duplicate using Hue, Saturation, Brightness.
- Duplicate the grayscale layer, then open Curves and invert it by flipping the curve so it slopes downhill.
- Change the inverted layer's blend mode to Color Dodge. It sits in the Lighten tab of the blend mode panel. The canvas will turn mostly white.
- Apply Gaussian Blur to the inverted layer until the line drawing appears.
If you get high-contrast black and white with no lines, the blur is usually too low or applied to the wrong layer. If you see a yellow cast instead of white, check that the layers beneath the inverted one are fully desaturated.
Keeping color: a "sketch over color" look
If you want a colored drawing rather than pure line art, a stacked-layer version works:
- Insert the photo, duplicate it, and desaturate the duplicate.
- Duplicate the grayscale layer, set it to Divide, and blur it until it reads like a pencil sketch.
- Hide that middle sketch layer, or delete it if you don't need it.
- Duplicate the original color layer and drag it to the top of the stack.
- Set the top color layer's blend mode to Overlay.
- Choose a plain, solid brush in black. A monoline-style brush works well. Make it large and paint across the whole canvas to build the effect.
- Duplicate the top layer if you want the colors stronger.
Overlay painting is non-obvious, so expect to experiment. Swap in a different blend mode or reduce layer opacity if the colors feel heavy.
Coloring underneath the line art
The Divide method leaves a white background baked into the lines, so you can't paint behind them directly. Fix this by changing the line layer's blend mode to Multiply. Linear Burn, Color Burn, and Darken also work, with small differences in how dark the lines render. Then add a new layer beneath the line art and paint your colors there. The white drops out and the lines sit on top of your color. Bring back the original photo layer underneath if you want a hybrid look.
The same trick works for scanned traditional inking. Set the scan to Multiply, adjust levels until the paper reads as white and the lines are dark, then color on a layer below.
Method 3: Trace it by hand
If you want a stylized illustration rather than a filter-like result, trace manually:
- Insert the photo and lower its opacity.
- Create a new layer above it.
- Draw in big, confident strokes. Simplify rather than copy: fewer rings on a tire, fewer wrinkles on a face.
- Add a second layer for refinement and clean up details.
- Hide or delete the photo layer.
Tracing gives you control over line weight, hierarchy, and stylization that the blend-mode method can't. It also takes longer. For reference sheets and quick studies, the Divide method is usually enough. For finished art, tracing wins.
Two Procreate settings speed this up: enable the square-plus-Apple-Pencil gesture to select layers by tapping on the canvas, and hold a line at the end of a stroke to snap it straight.
Honest limits of the Procreate approach
Know what you're getting before you build a pipeline around it:
- It's raster only. Procreate produces bitmap images, not vectors. If you need scalable paths, you'll trace the result in another tool.
- Edges are softer than a dedicated edge filter. Comparisons against Photoshop's Find Edges show a sharper result there. The blend-mode method is close, not identical.
- Results depend on the source. High-contrast, well-lit photos produce cleaner lines than flat or noisy images.
- It's a single frame. Every step is manual and per-image. Running the same recipe on 100 frames of video isn't practical in Procreate.
Getting the drawing into After Effects
For motion work, treat Procreate as a still-image stage:
- Export the right format. Choose a format that keeps transparency, and keep your layers separate if you want to animate them.
- Keep layers separate. Export lines, color, and background as distinct layers so you can animate and composite them independently in After Effects.
- Work at a high resolution. Set your Procreate canvas to your delivery size, or larger, so you can scale and push in without softening the lines.
- Use the line art as a matte or texture. A Divide-style line layer works well as a luma matte, a displacement source, or a boil/jitter base for hand-drawn animation effects.
Taking the look to video with Styleframe
Procreate handles one frame at a time. If you want the same drawn look across moving footage, or you want to animate between drawn key poses, a video tool like may fit.
A practical workflow: build your look in Procreate on a couple of key frames, use those as style references in a video tool, generate the motion, then finish color, grain, and compositing in After Effects. You keep your compositing stage.
Quick troubleshooting
- Canvas stays white after Divide: you haven't applied Gaussian Blur yet, or you applied it to the wrong layer.
- Lines look too faint: open Curves and pull the bottom point right, or lower the blur.
- Lines are too heavy and blotchy: reduce the blur.
- Can't find blend modes: tap the small letter on the layer thumbnail beside the visibility checkbox. Color Dodge sits in the Lighten tab.
- Can't paint behind the lines: set the line layer to Multiply and add a new layer underneath.
The short version
For fast line art, use Divide with Gaussian Blur. For a stylized result, trace manually. For color, use Overlay or paint beneath a Multiply line layer. Export layers separately for After Effects, and when you need the look to carry across moving footage, use your Procreate frames as references for a video tool like Styleframe.