How to Turn on Correction O Procreate
StyleFrame Team6 min read
Procreate has no single "correction" switch. The feature people usually mean is line smoothing, which you turn on per brush with StreamLine and Stabilization in Brush Studio, or globally through Procreate's global stabilization settings. If your lines are snapping into perfect shapes instead, that is QuickShape, which you control under Actions (wrench) → Prefs → Gesture controls → QuickShape.
What "correction" means in Procreate
The phrase in the keyword is loose, and Procreate doesn't use "correction" as a menu label. Depending on what you're trying to fix, you want one of three things:
Many people searching this are drawing a line, watching it wobble, and wanting the app to clean it up. Start with stroke stabilization, then check QuickShape if the app is "correcting" too aggressively.
How to turn on StreamLine and Stabilization for a brush
Procreate applies stroke smoothing at the brush level. Each brush carries its own settings, so you can have a heavily smoothed inking brush and a loose sketching brush in the same set.
- Open the Brush Library and tap the brush you want to adjust. This opens Brush Studio.
- Select the Stabilization attribute from the list.
- Raise the StreamLine Amount slider. Higher values give a smoother, more even result. Lower values or zero give more natural, hand-shaky linework.
- Adjust the StreamLine Pressure slider. Higher values make pressure build up over a longer, smoother stretch. Lower values make pressure kick in faster as you press.
- Raise the Stabilization Amount if you need more smoothing than StreamLine alone gives you.
- Test in the drawing pad in Brush Studio, then exit Brush Studio.
The two controls do different jobs:
- StreamLine smooths wobbles and shakes in the line as you draw. It matters most for inking and calligraphy.
- Stabilization takes a moving average of the stroke and draws that on the canvas. The higher the value, the more it averages out wobbles, which makes strokes more deliberate and controlled.
If you break a brush while experimenting, Brush Studio has a reset option, so you can push the sliders around without worry.
Starting values
There are no universal numbers, because the right amount depends on your drawing speed, canvas size, and zoom level. A useful approach:
- Draw a long curve, a tight curl, and a straight stroke with the sliders at zero.
- Raise StreamLine in small steps until the curve stops shaking.
- Stop when the line begins to lag or feel disconnected from your pencil. Over-smoothing rounds off sharp corners and makes fast strokes feel mushy.
- Add Stabilization only if StreamLine alone isn't enough for the stroke length you're drawing.
How to turn on stabilization globally
If you want the same smoothing on every brush, Procreate offers global stabilization settings. The Handbook places them under Accessibility in the Interface and Gestures section. The exact menu layout can shift between Procreate versions, so check the Handbook page for your version if you can't find it.
Global settings suit people who need constant smoothing across the board, such as artists with a tremor or anyone drawing on a small screen. Per-brush settings suit people who switch between textured sketching brushes and clean inking brushes, because a single global value will be wrong for one of them.
If Procreate is "correcting" lines you didn't want corrected
The opposite complaint is common too. You pause at the end of a stroke, and Procreate snaps the line straight or turns your scribble into a perfect shape. That is QuickShape, triggered by Draw and Hold. You can tune it or disable it:
- Tap the wrench icon to open Actions.
- Go to Prefs → Gesture controls.
- Tap the QuickShape tab on the left.
- Use the delay slider for Draw and Hold. Moving it to the right increases how long you must hold before the shape snaps.
- To stop Draw and Hold from triggering it, toggle that option off. You can enable another trigger instead, such as one that uses the square Modify button, so shape correction only happens when you ask for it.
- To disable QuickShape completely, make sure every option in that tab is toggled off.
One quirk: one user reports that on iPhone this setting is even less obvious, because it is hidden in the Timers preferences. If you can't find it on iPhone, look there.
Practical fixes for wobbly lines beyond the sliders
Software smoothing helps, but it doesn't replace technique, and heavy smoothing has costs. A few habits make smaller slider values workable:
- Warm up first. Quick ovals, circles, crosshatching in both directions, and arcs get the shake out of your hand before you start the real drawing.
- Draw from the shoulder and wrist, not the fingers. Use the natural arc of your hand rather than forcing a stroke against it.
- Rotate the canvas. Turn the canvas so the curve you're drawing falls in your hand's comfortable direction instead of fighting it.
- Match smoothing to the task. Use high StreamLine for final line art and low or none for gestural sketching, where a little wobble reads as energy.
- Check brush scaling. In Prefs, if brushes behave unexpectedly as you zoom, setting Brush scaling to "relative to canvas" is a sensible default, since many brushes are designed around it.
If you meant color correction
Some people say "correction" and mean color. Two features cover common cases:
- Adjustments is the menu to check for general color changes.
- Recolor changes the color of an area on a layer. It is a Quick Menu action, so you may need to assign it first: Actions → Prefs → Gesture controls → Quick Menu, then set one of the boxes to Recolor. When active, a crosshair appears. Drag it onto the area you want to affect, and change the selected color on the color wheel to see the result in real time. If the whole background changes color, the crosshair is probably in the wrong spot. Also confirm you're on the correct layer, and use the flood threshold slider if the fill isn't covering everything.
Troubleshooting
Smoothing seems to do nothing. You may be editing a different brush than the one you're drawing with. Stabilization is stored per brush, so confirm the active brush is the one you adjusted, or use the global setting.
Lines lag behind the pencil. Your StreamLine or Stabilization values are too high. Back off until the stroke follows your hand closely enough for the work you're doing.
Corners look rounded. Same cause. For lettering and technical linework, lower the smoothing and draw each segment deliberately, or use QuickShape's straight-line behavior on purpose.
Shapes keep snapping. Raise the QuickShape delay or switch off Draw and Hold, as described above.
You changed something and can't undo it. Reset the brush in Brush Studio rather than trying to remember the original values.
Quick answer checklist
- Smoother lines: Brush Library → tap brush → Stabilization → raise StreamLine Amount (and Stabilization if needed).
- Same smoothing everywhere: use the global stabilization settings (the Handbook lists them under Accessibility).
- Unwanted snapping: Actions → Prefs → Gesture controls → QuickShape → increase delay or toggle options off.
- iPhone: one user reports the QuickShape settings are hidden in the Timers preferences.
- Color changes: use Adjustments, or assign Recolor to the Quick Menu.
Set the smoothing per brush, keep it as low as your hand allows, and treat QuickShape as a tool you invoke rather than one that fires on its own.