How to Turn Off Recolor in Procreate
StyleFrame Team6 min read
Recolor in Procreate isn't a setting you can switch off. It's a temporary mode, so you leave it by finishing or abandoning the change you're previewing. Tap the canvas to commit the preview, then select any other tool to exit. If you don't want the change, two-finger tap to undo. To stop triggering it by accident, remove the Recolor shortcut from your Quick Menu under Actions > Preferences > Gesture controls.
What Recolor Mode Actually Is
Recolor replaces colors on the active layer with your currently selected color, using a crosshair you drag around the canvas as a live preview. Wherever the crosshair sits, Procreate samples the color underneath and previews the swap across similar pixels on that layer. Nothing is permanent until you tap the canvas.
You can enter Recolor mode in two ways:
- From the Quick Menu, if you've assigned Recolor to one of its buttons. Many artists do this because Recolor isn't listed in the Adjustments menu with the other color tools.
- From ColorDrop, by dragging a color onto a shape and tapping the "Continue filling with Recolor" button that appears at the top of the screen.
Either route puts you in the same state: a crosshair on the canvas, a Flood slider at the bottom, and a preview that follows your Apple Pencil or finger. That state is what people usually mean when they say Recolor is "stuck on."
How to Exit Recolor Mode
The right exit depends on whether you want to keep what you're previewing.
If you want to keep the change
- Position the crosshair over the area you want to change.
- Tap the canvas to commit the new color.
- Select another tool to leave the mode.
If you tap again before switching tools, you'll commit another change wherever the crosshair currently sits. If you're done, move straight to a different tool.
If you don't want the change
Switch to another tool without tapping the canvas. The preview is just a preview until you commit it, so there's nothing to reverse. If you've already tapped and don't like the result, use the undo steps below.
If the crosshair keeps reappearing
That may be the Quick Menu shortcut or a gesture being triggered by a stray touch. See the section on preventing accidental activation.
How to Undo a Recolor You've Already Committed
Once you've tapped the canvas, the change is applied to the layer's pixels. To reverse it:
- Two-finger tap on the canvas to undo the last action. Repeat to step back through multiple recolor taps.
- If you've done many steps since the recolor, use the undo gesture or the undo arrow in the sidebar rather than trying to repair it by hand.
If undo isn't an option, you'll need another approach. That's why it pays to work non-destructively before you recolor, covered below.
How to Stop Recolor From Triggering by Accident
If Recolor keeps popping up, it may be assigned to a gesture or Quick Menu button you're hitting unintentionally.
- Open the Actions menu (the wrench icon).
- Go to Preferences > Gesture controls.
- Open Quick Menu and check which gesture invokes it. If you've mapped it to something you tap often (such as the square between the size and opacity sliders), choose a different gesture or a deliberate one like a touch-and-hold.
- Back on the canvas, open the Quick Menu, tap and hold the button currently set to Recolor, and choose a different action from the alphabetized list.
Recolor stays available through ColorDrop; you just won't hit it by accident.
When Recolor Gives You Results You Didn't Want
Sometimes people want to "turn off" Recolor because it's changing the wrong thing. Before abandoning the tool, check these causes:
- Wrong layer. Recolor only affects the active layer. With a stack of layers, confirm which one is highlighted before you start.
- Crosshair position. The color it replaces comes from wherever the crosshair sits. If it's over the background, the background will change. Drag it onto the element you actually want.
- Flood slider too high. A high Flood value bleeds the new color into similar shades. On painterly or textured art, that can swallow neighboring areas. Lower it to constrain the change.
- Active color. Recolor uses your current color. Changing the color in the panel updates the live preview, which is handy for auditioning options but easy to forget.
- Textured brushwork. Soft edges and varied values produce uneven results. Expect to adjust Flood and tap in several passes rather than one.
If it still doesn't behave, a different tool may suit the job better.
Non-Destructive Alternatives to Recolor
Recolor edits pixels directly. If you want to experiment freely, set things up so you can always get back to the original:
- Duplicate the layer before recoloring and hide the original. If the result is wrong, delete the copy.
- Use a clipping mask. Add a new layer above your artwork, clip it to the layer below, set its blend mode to Color, and paint on it. Your underlying linework and shading stay untouched, and you can delete or adjust the color layer at any time.
- Use Adjustments instead. Hue, Saturation, Brightness and Color Balance (in the Adjustments menu) apply across a layer, with Apply, Preview, and Cancel options before you commit. They're better for global shifts, such as moving an entire palette warmer, while Recolor is better for targeted swaps.
- Use Curves when you need to shift color and contrast together.
A useful rule: reach for Recolor when you need to swap specific colors quickly, and for adjustments or clipping masks when you need reversibility.
Handling Color Changes After Procreate
Many motion designers and animators use Procreate for illustration, character design, or frame-by-frame elements, then move the work into After Effects, Premiere Pro, Blender, or Nuke. Deciding where to recolor can save you a lot of rework.
If a color might change later, keep it flexible in the file you export:
- Export layered or separated elements (PSD or individual PNGs) so each color-critical piece stays on its own layer.
- Hold color on separate clipped layers in Procreate so you can export a flat version and a version without the color layer.
- Recolor in the compositor. In After Effects and Nuke, color-correction effects and nodes let you adjust color without touching source pixels.
For this kind of work, color changes done in the comp are easier to revise after client feedback than pixels baked in on an iPad.
Quick Reference
FAQ
Is there a Recolor toggle in Procreate's settings? No. Recolor is a mode you enter and leave, not a preference. The closest thing to disabling it is removing it from your Quick Menu.
Does Recolor affect all my layers? No, only the active layer. Check your layer selection first.
Can I recolor without changing the original pixels? Not with Recolor itself. Duplicate the layer first, or use a clipped layer with the Color blend mode for a reversible workflow.
Why does Recolor change my whole background? The crosshair was probably over the background, or the Flood slider was high enough to spread the color across similar shades. Move the crosshair onto the element you want and lower Flood.