How to Turn Off Opacity Pen Pressure Procreate
StyleFrame Team7 min read
To turn off opacity pen pressure in Procreate, open the brush, tap Apple Pencil in Brush Studio, and set the Opacity sliders under Pressure (and Tilt, if present) to zero. Procreate has no global on/off switch for pressure sensitivity, so the change applies per brush. Duplicate the brush first so the original stays intact. If you want a flatter response across every brush, you can also flatten the pressure curve in Actions > Prefs.
The Fast Version
- Tap the brush you want to change, then tap it again to open Brush Studio.
- Select the Apple Pencil tab.
- Under Pressure, drag Opacity to zero. Do the same for Flow if the stroke still fades.
- Under Tilt, set Opacity to zero if the stroke still changes when you angle the pencil.
- Tap Done, then test on a blank layer.
Slider labels shift slightly between Procreate versions, so treat the names as a guide. The principle stays the same: any slider tied to pressure or tilt that touches opacity, flow, or size should sit at zero if you want the brush to behave like a fixed-value marker.
Why Procreate Has No Single Toggle
Procreate treats pressure as a property of each brush, not a device-wide mode. Every brush carries its own response to pressure and tilt, which is why a pencil brush and an inking brush feel so different with the same stylus.
Users have asked for a master switch that disables pressure sensitivity entirely, so that size and opacity come only from the brush settings. As of the last discussions we've seen, that request is a suggestion, not a feature. Until it exists, there are three reliable workarounds: edit the brush, flatten the pressure curve, or build a dedicated set of brushes with pressure turned off.
Method 1: Edit the Brush in Brush Studio
This is the most precise method because you control exactly which behaviors change.
Duplicate before editing
Swipe left on a brush in the Brush Library and tap Duplicate. Rename the copy something obvious, like "Mono Line – No Pressure." Default brushes can reset on major updates, while custom brushes keep the settings you gave them.
Zero out the right sliders
In the Apple Pencil tab, check each of these:
- Pressure > Opacity: controls how pressing harder darkens the stroke. This is the one most people are looking for.
- Pressure > Flow: affects how much paint builds up with pressure. It can look like an opacity change, so zero it as well.
- Pressure > Size: changes line thickness. Zero it if you want a constant width.
- Tilt > Opacity and Tilt > Size: angling the pencil can shade or thicken a stroke even when pressure is flat.
If you only zero the pressure sliders, a brush can still behave unpredictably because tilt is doing the work. Check both.
Watch for other dynamics
Some brushes may have additional behaviors in other tabs, such as velocity-based dynamics. If opacity still wobbles after you zero the Apple Pencil tab, look for speed-driven jitter or grain settings that darken or lighten the stroke.
Method 2: Flatten the Pressure Curve
If you don't want to edit individual brushes, change the global response.
- Tap the Actions (wrench) icon.
- Go to Prefs > Pressure and Smoothing.
- Open Edit Pressure Curve.
- Drag the curve into a flat, high line so almost any touch registers as the same pressure.
This affects every brush, which is both the benefit and the drawback. The curve alone doesn't truly disable pressure. A flat curve means the pencil reads the same pressure regardless of how hard you press, but tilt can still change shading, and the result sits at a fixed point on the brush's range, not necessarily at full opacity. It's good for a quick session of clean line work and less good when you need exact, predictable values.
Remember to restore the curve afterward, or your painterly brushes will feel dead.
Method 3: Build a "No Pressure" Brush Set
For anyone doing precise work repeatedly, a dedicated brush set is the most practical long-term solution.
- Create a new set in the Brush Library and name it something like "Constant."
- Duplicate a hard round brush, a soft round brush, a texture brush, and an eraser.
- Zero the Pressure and Tilt sliders on each.
- Drag the duplicates into the new set.
Now switching between expressive and mechanical drawing means switching sets, not re-editing sliders. Don't forget the eraser, which has its own brush settings. An eraser that changes strength with pressure is one of the most common frustrations when cleaning up flat shapes.
Other Ways to Get Constant Opacity
Use your finger
Finger input has no pressure data, so brushes draw at their set values. It's less precise than a pencil nib, but it works for fills and blocking in shapes.
Use a non-pressure stylus
A basic capacitive stylus doesn't report pressure. Some newer Apple Pencil models also omit pressure sensitivity, which makes them a hardware option if you never want it.
Lock opacity with layer features
If you only need uniform results in the final image, use Alpha Lock or a clipping mask and fill with a flat color. Another option is to draw a rough shape and use QuickShape or a selection with Color Fill to produce a solid, even area.
Use the opacity slider as a cap
The sidebar opacity slider sets a ceiling for how opaque a stroke can be. It doesn't remove pressure response, but it can limit how dark the stroke gets.
Troubleshooting
Opacity still varies after zeroing pressure. Check tilt, flow, and any velocity or dynamics settings. Also confirm you edited the brush you're actually using; duplicates are easy to mix up.
Strokes look jagged or uneven. That may be Streamline or Stabilization, not pressure. Adjust those in Brush Studio.
The eraser still fades. The eraser is a separate brush. Open its settings and repeat the process.
Changes disappear. If you edited a default brush, an update may have reset it. Custom duplicates avoid this.
Opacity looks different on overlap. Overlapping strokes build up on a single layer. To avoid it, work in one continuous stroke, or put each element on its own layer.
Why This Matters for Motion and VFX Work
Procreate often serves motion designers as a quick sketch and paint tool for storyboards, style frames, hand-painted textures, and rough mattes. In those cases, consistent opacity matters for practical reasons:
- Mattes and masks: Uneven opacity in a hand-painted matte creates soft spots that show up as flicker or edge variation once it's keyed or used as a track matte in After Effects or Nuke.
- Cel-style animation frames: Frame-by-frame cleanup needs solid fills and lines that match across frames, or the result shimmers in playback.
- Texture and displacement maps: Painted maps for Cinema 4D or Blender should have predictable values, since pressure variation turns into unintended height or roughness changes.
- Style frames: Flat, controlled color blocks are easier to hand off and re-light than strokes with accidental transparency.
For export, save PNGs with transparency, or PSD if you need to keep layers. Check that the canvas is sized for your comp resolution, so you aren't scaling up painted edges later.
Where Styleframe Fits in This Workflow
If your Procreate drawings are heading toward animation, constant-opacity artwork makes better reference material. A clean, flat-value drawing from Procreate can serve as a keyframe or style reference in an animation tool such as Styleframe.
Because tools like this lean on your references, tidy inputs tend to give you more predictable results than drawings with unintended soft spots.
You don't need Styleframe to fix a pressure problem in Procreate. It's simply a next step once you have clean artwork and want to move it into motion without giving up control over the look.
Quick Reference
FAQ
Is there a way to turn off pressure sensitivity in Procreate for all brushes at once? Not with a single switch. Flattening the pressure curve is the closest global option, and a custom brush set is the most reliable.
Will zeroing the sliders affect my other brushes? Only the brush you edit. That's why duplicating first is worth the extra step.
Can I undo it? Yes. Reset the sliders to their previous values. If you duplicated the brush first, the original stays untouched.