How to Turn Down Opacity of Layer in Procreate Pocket
StyleFrame Team6 min read
To turn down layer opacity in Procreate Pocket, tap the Layers icon (two overlapping squares next to the Colors button), then tap the small letter at the right of the layer's name, which reads "N" by default. Drag the Opacity slider left to make the layer more transparent. At 100% the layer is fully opaque, and lower values let more of the layers beneath show through. Because the setting lives on the layer, you can reopen it and change it as often as you like.
Step-by-step: lower layer opacity in Procreate Pocket
- Expand your tools if needed. If the toolbar is condensed, tap the ellipsis icon to reveal the full set of tools.
- Open Layers. Tap the overlapping-squares icon beside Colors. The panel slides up from the bottom of the screen, so you can see canvas changes in real time while you work.
- Select the layer. Tap the layer to make it active. Swipe up and down to find it in a long stack, or drag the pull handle at the top of the panel upward to expand the list.
- Tap the blend mode letter. The "N" (Normal) to the right of the layer name opens the blend mode and opacity menu.
- Drag the slider left. Watch the percentage and the canvas together. Stop when the layer sits where you want it.
- Dismiss the menu. Tap outside it or on the canvas. The value stays with the layer.
This is the most dependable route on Pocket because everything sits in one panel. It also puts blend mode and opacity side by side, which is useful when you are building overlays, glows, or shadow passes.
Alternative ways to reduce opacity
The two-finger shortcut
Procreate's guides describe a gesture where you tap a layer with two fingers at once, then slide a finger left or right on the canvas. A bar at the top of the screen shows the percentage as it changes. This is documented most clearly for the iPad version, so if it doesn't respond on your Pocket version, fall back to the "N" menu. When it works, it is faster for quick tweaks because you never leave the canvas.
Adjustments > Opacity
The Adjustments menu has an Opacity tool that works on the active layer's contents. You slide left and right on the screen, and a bar at the top shows the current value, starting at 100%. Buttons let you cancel, undo, redo, or reset. The change is applied when you tap Adjustments again or switch tools.
This is a commit-style adjustment, so it behaves differently from the layer slider. If you may want to revisit the value later, use the layer's own slider.
Opacity on a selection
If you only want part of a layer to fade:
- Make a selection with your preferred method.
- Open Layers.
- Two-finger tap the layer holding the paint.
- Slide left to reduce opacity or right to increase it.
Exiting this mode applies the change to the pixels, and you cannot readjust it later the way you can with the layer slider. Duplicate the layer first if you want a safety net, or put the selected area on its own layer and use the standard slider.
Layer opacity vs. brush opacity
A common source of confusion is lowering the wrong opacity. They are separate controls:
- Layer opacity changes how visible everything on a layer is. It's what you want for ghosting, tracing underlays, fading reference sketches, and softening overlays.
- Brush opacity changes how strong each new stroke is as you paint. It does nothing to existing marks.
Brush opacity is the lower slider on the sidebar. If your strokes look too faint even with the slider maxed out, Apple Pencil pressure sensitivity may be affecting the brush, since many brushes respond to pressure.
If you turned down a layer and nothing seems to change, check whether you were adjusting the brush. If you turned down the brush and old marks look unchanged, that's expected.
Practical uses for lowered layer opacity
For artists who normally live in timelines and node graphs, the same habits translate directly:
- Onion-skin style tracing. Drop a rough layer to 20–30% and draw clean key poses on a new layer above it.
- Storyboard and animatic underlays. Keep a composition guide faint so it informs framing without competing with the drawing.
- Atmosphere and mood passes. Paint haze, light wraps, or color washes on a separate layer and dial them in with the slider.
- Reference matching. Lay a screenshot or photo at partial opacity and overpaint to match shapes or palette.
- Clipping masks. A clipped layer inherits the shape of the layer beneath it, so you can fade a texture or shading pass without it spilling past the base shape.
Troubleshooting common problems
The slider doesn't appear. Make sure you tapped the letter to the right of the layer name, not the visibility checkbox. The checkbox only hides or shows the layer. Tapping and holding it solos the layer, which can look like a broken opacity setting. Tap and hold again to turn solo mode off.
The wrong layer faded. Opacity applies to the active layer. In a stack, confirm which one is highlighted before dragging.
The canvas shows a background you didn't want. The background color is a separate layer-like element. Untick its checkbox when you want to export a PNG or TIFF with transparency, so lowered-opacity layers don't blend into a solid color.
Strokes are too faint. Check brush opacity and Pencil pressure, not layer opacity.
Taking Pocket artwork into a motion pipeline
Procreate Pocket is handy for sketching boards, texture studies, and style references on the go. The step that matters for production is getting that work out in a form your compositing software handles predictably.
- Export layered files when you need adjustments downstream. Open the exported file in your compositing software and verify that your lowered opacity values carried over before you commit to a timeline.
- Export flattened PNG or TIFF for reference. Turn off the background color first if you need transparency.
- Keep faded layers for flexibility. Opacity set with the slider is non-destructive, so duplicating a file and exporting variants with different values is quick. Applying opacity through Adjustments or on a selection bakes it in.
- Rebuild the final look in your compositor. Treat Pocket opacity as a design decision, not a render setting.
Quick reference
Final tips
Start with the layer's own slider for anything you might change later, and reserve selection-based and Adjustments opacity for deliberate, final edits. Name layers that serve as guides so you can find them quickly, and keep underlay layers separate from final linework so you can hide or delete them at export. If a result looks wrong, confirm you adjusted layer opacity rather than brush opacity, and make sure the layer isn't being soloed.