How to Turn Down Opacity of Layer in Procreate
StyleFrame Team7 min read
To turn down a layer's opacity in Procreate, open the Layers panel in the top right, tap the "N" to the right of the layer name, and drag the Opacity slider left. A faster route is to tap the layer with two fingers and slide left on the canvas to lower the value, or right to raise it. Both methods change the layer as a whole and can be re-edited at any time.
How to Lower Layer Opacity from the Layers Panel
This is the most controlled method because it shows a numeric value and leaves the layer's pixels untouched.
- Tap the Layers icon (two overlapping squares) in the top right corner.
- Find the layer you want to change. Procreate adjusts one layer at a time.
- Tap the small letter to the right of the layer name. It reads "N" by default, which stands for Normal blend mode.
- Drag the slider beneath the blend mode list to the left. At 100% the layer is fully visible, and at 50% it is half see-through.
The same panel holds the blend mode list, so you can set opacity and blend mode in one place. Because the slider can be changed repeatedly, this counts as a non-destructive edit. You can return to 100% tomorrow and nothing will have been lost.
The Two-Finger Shortcut
If you're sketching and want to fade a layer without opening menus, use the gesture:
- Open the Layers panel.
- Tap the target layer with two fingers at the same time. The index and middle finger of one hand work well.
- A bar labelled with the opacity percentage appears at the top of the screen.
- Slide a finger left on the canvas to lower opacity, or right to raise it.
- Lift your finger to set the value.
This is the fastest way to turn down a guide layer, such as a rough sketch you're inking over, while keeping your eyes on the canvas. The downside is precision. The gesture is harder to land on an exact number than the slider, so use the panel when you need a specific value like 35%.
Using Adjustments > Opacity
Procreate also has an Opacity tool in the Adjustments menu.
- Select the layer you want to change.
- Tap Adjustments, then Opacity.
- Slide your finger left or right across the screen. The blue "Slide to adjust" bar at the top shows the current value, starting at 100%.
- Use the buttons along the bottom to cancel, undo, redo, or reset while staying in the tool.
- Tap the Adjustments icon again, or choose any other tool, to commit the change. Tap Cancel to leave without applying anything.
This method suits people who like a preview-then-commit flow. It also affects only the active layer's contents. The practical difference from the Layers panel slider is the commit step: you confirm the change before it takes effect.
Lowering Opacity on Just Part of a Layer
Sometimes you only want to fade part of a drawing, such as one shape on a layer that contains several. Procreate handles this through selections.
- Tap the Selection tool and pick a method.
- Make your selection.
- Open the Layers panel and tap the layer with two fingers.
- Slide left on the canvas to reduce the selection's opacity, or right to increase it.
Be aware of what happens when you exit this mode: the change is applied. It is a destructive edit. You can undo it right away, but you can't revisit the value later the way you can with the layer slider. If you think you might want the original opacity back, duplicate the layer first, or cut the selection onto its own layer and lower that layer's opacity instead. That preserves the option to change your mind.
Layer Opacity vs. Brush Opacity
A common source of confusion is the difference between the opacity of a layer and the opacity of a brush. They are separate controls.
- Layer opacity changes how visible everything on that layer is. It's set in the Layers panel or with the two-finger gesture.
- Brush opacity changes how visible new strokes are as you paint. It's the lower slider on the sidebar. Drag it down to make strokes lighter, and up to make them stronger.
If your strokes look too faint even with the brush opacity maxed out, check Apple Pencil pressure. Many brushes tie opacity to pressure, so a light touch gives transparent marks. Lowering a layer's opacity won't fix that, and raising it won't either. The brush's pressure settings are the cause.
Which Method Should You Use?
For most work, stick with the layer-level slider. It keeps your file flexible.
Troubleshooting Common Opacity Problems
The slider doesn't seem to do anything. Check that you've selected the right layer.
The layer looks faded but the slider says 100%. Look at the blend mode. Modes like Multiply or Overlay change how a layer interacts with what's below it, which can look like an opacity change. Set the mode back to Normal to compare.
Strokes are too light. Check brush opacity and the pencil pressure curve, not the layer setting.
You applied a selection opacity change and want it back. Undo immediately. If it's too late, repaint or restore from a duplicate layer.
Carrying Procreate Opacity Into a Motion Workflow
Many motion designers and animators use Procreate for boards, style frames, textures, and hand-drawn elements before moving to After Effects, Premiere Pro, Blender, or Nuke. A few habits make that handoff smoother.
- Keep opacity at the layer level. If a ghosted element is faded with the layer slider rather than with a baked selection edit, you can rebuild or retune it later.
- Name your layers. When you export a layered file, clear names make it easy to find the element you faded.
- Test one export. Before relying on a layered export for a big project, bring a small test file into your compositing app and confirm that layer opacity and blend modes arrive as you expect. Behavior can differ between apps, and a quick check is cheaper than discovering a mismatch late.
- Flatten selectively. If you want a precise look that won't shift between apps, export a flattened PNG or image sequence of the final appearance and use it as a plate.
Where Styleframe Fits After the Procreate Step
Procreate is good for the hand-made part of a look: a painted keyframe, an ink pass, a texture study. Styleframe is an AI video and motion tool built for artists who want control over the next step, turning that work into moving footage.
In practice, the artwork you finish in Procreate, with opacity values you've tuned, can become the reference for a Styleframe generation. Your compositing workflow stays where it is. Opacity, blend modes, and final grading still happen in the comp, and Styleframe supplies source material.
FAQ
Can I set an exact opacity number in Procreate? Yes. The Layers panel slider shows the percentage as you drag, and the Adjustments > Opacity bar also displays the current value.
Is lowering layer opacity destructive? No, not when you use the Layers panel slider or the two-finger gesture. You can change the value as often as you like. Selection-based opacity changes are applied when you exit and can't be re-adjusted afterward.
Does lowering opacity affect the brush? No. Layer opacity and brush opacity are separate. Brush opacity is the lower sidebar slider and only affects new strokes.
Can I lower the opacity of several layers at once? Layer opacity is set one layer at a time.
What's the quickest way to reset opacity? Open the layer's "N" menu and drag the slider back to 100%, or undo if you've just made the change.