How to Turn Down Image Opacity on Procreate
StyleFrame Team6 min read
To turn down image opacity in Procreate, open the Layers panel, tap the "N" to the right of the layer name, and drag the opacity slider left. You can also tap the layer with two fingers and slide left on the canvas, which shows a live percentage at the top of the screen. Opacity is set per layer, so both methods work on any layer that contains your image. Brush opacity and selection opacity are handled separately, covered below.
What opacity means in Procreate
Opacity is how visible a pixel is. At 100%, it is fully visible, and at 50%, it is half see-through. Procreate lets you control this in three places:
- Layer opacity: the whole layer, including everything painted or imported onto it.
- Brush opacity: how transparent new strokes are as you paint.
- Selection opacity: only the isolated pixels inside a selection.
Most people searching for this want layer opacity. When you drop in a reference photo, a scan, or a placed image, keep it on its own layer so you can lower its opacity the same way as for any paint layer.
The three methods behave differently when it comes to editing later. Layer opacity can be changed repeatedly, so it's non-destructive. Selection opacity commits when you exit, so treat it as final.
Method 1: Lower opacity from the Layers panel
This is the most explicit method and the one to learn first.
- Tap the Layers icon in the top right corner.
- Find the layer containing your image.
- Tap the small letter to the right of the layer name. It reads N by default, for Normal blend mode.
- A panel opens with blend modes and an opacity slider at the top. Drag the slider left to reduce opacity and right to increase it.
The percentage readout makes this good for precision. If you need exactly 35% for a tracing reference, you can land on it and confirm the number. The same panel also holds blend modes, so you can switch from Normal to Multiply or Screen without leaving it.
Method 2: The two-finger tap shortcut
This is the faster gesture once you're comfortable with it.
- Open the Layers panel.
- Tap the target layer with two fingers at the same time. The index and middle finger of one hand work well.
- An opacity slider appears at the top of the screen.
- Slide your finger or Apple Pencil left to make the layer more transparent, or right to make it more opaque.
Because it responds to a swipe anywhere on the canvas, it suits quick visual adjustments, such as fading a reference image until your line work reads clearly. You can adjust only one layer at a time with either method, so if you have several reference images, repeat the steps for each layer or group them first.
Method 3: Adjustments > Opacity
Procreate also has an Opacity tool in the Adjustments menu, which acts on the active layer.
- Select the layer.
- Tap Adjustments and choose Opacity.
- Slide left or right with a finger. A blue bar labeled "Slide to adjust" shows the current value, starting at 100%.
- Use the bottom buttons to cancel, undo, redo, or reset.
- Commit by tapping the Adjustments icon again or choosing another tool.
This method is useful when you want the undo/redo/reset controls while experimenting. Until you commit, you can cancel everything. After you commit, use the layer slider instead if you want to keep revisiting the value.
Lowering brush opacity versus layer opacity
A common mistake is reducing the wrong thing. If your image is already on the canvas and you want it more transparent, you need layer opacity. Brush opacity only changes how strokes you paint from now on.
To lower brush opacity:
- Select a brush.
- Drag the lower slider in the sidebar down to decrease opacity, or up to increase it.
If your brush looks too faint even though the slider is at maximum, pen pressure is probably the cause. Many brushes tie opacity to Apple Pencil pressure, so a light touch gives transparent marks regardless of the slider. Check the brush's pressure settings if this keeps happening.
Lowering opacity on part of an image
To fade only one region of an image:
- Open Selections and choose a method (such as Automatic).
- Make your selection.
- Open the Layers panel and tap the layer with two fingers.
- Slide left on the canvas to reduce opacity inside the selection, or right to increase it.
Once you exit this mode, the change is applied. You can undo it immediately, but you can't return later and adjust the value. If you want a revisitable partial fade, use a duplicate-layer workflow instead: duplicate the image layer, erase the part you want faded, then lower the opacity of that layer using the Layers panel. Layer opacity stays editable.
Common problems and fixes
The slider doesn't appear. Make sure the right layer is selected, and that you tap with two fingers at once. A two-finger tap on the layer opens the opacity control.
Opacity changes the wrong content. If you've painted on the same layer as the image, the slider affects everything on that layer. Separate the image onto its own layer before lowering opacity.
The image looks washed out after lowering opacity. That's expected over a light background. Try a blend mode such as Multiply for line drawings or Screen for light elements, instead of relying only on transparency.
Why this matters for motion and VFX work
Many motion designers, animators, and compositors use Procreate for storyboards, style frames, hand-drawn elements, and quick paint-overs. Opacity control is part of the daily workflow: ghosting reference frames for onion-skin-style tracing, fading photo underlays beneath line work, or building soft overlays that become textures in comp.
A few habits keep this clean when art moves downstream:
- Keep opacity on layers, not baked into pixels. Layer opacity can be changed again, while selection-based opacity edits cannot. Before exporting, decide which transparency values are final.
- Name and group layers by purpose. Separate "reference," "line," "color," and "texture" layers so you can adjust or hide them independently.
- Export with layers where possible. Verify in your own pipeline that layer opacity and blend modes arrive as you expect, since behavior can vary between apps and settings.
- Export a flattened image as a safety copy. It gives you a visual reference of the intended look to compare against once layers are in comp.
Using Procreate art as a starting point in Styleframe
If your Procreate work is heading into motion, it can serve as source material for , an AI video and motion tool. A painted frame with the opacity balanced the way you want it is a useful input. None of this replaces the control you already have in Procreate.
Quick reference
Final tips
Use the N panel when you need an exact number, and the two-finger gesture when you're working by eye. If you expect to revisit the value, stay with layer opacity rather than selection opacity, and keep images on their own layers so you only affect what you mean to. Those habits save time in Procreate and keep the files flexible when they move into After Effects, Nuke, or any other stage of your pipeline.