How to Turn a Photo Into Line Art in Procreate
StyleFrame Team7 min read
To turn a photo into line art in Procreate, import the photo, desaturate it, duplicate the layer, invert the copy with Curves, set it to Color Dodge, and add a Gaussian Blur until the outlines appear. You can get a similar result by setting a blurred duplicate to Divide instead of inverting it. Procreate has no one-tap "photo to line art" filter, so this is a blend-mode technique you tune by eye, and tracing on a new layer is the cleaner option when you need deliberate linework.
What Procreate Can and Can't Do Here
Procreate is a raster painting app. It has no vectorize or find-edges filter, so any "automatic" line art comes from stacking adjustments and blend modes, which works like a manual edge-detect pass. The results are good enough for reference, storyboards, animatic panels, and stylized plates. They are less sharp than the Find Edges filter in Photoshop.
Knowing that shapes how you work. You are producing a bitmap whose line quality depends on the source photo's contrast, the canvas resolution, and your blur setting. Plan for that before you move the file into a motion pipeline.
Method 1: Invert and Color Dodge
This is the most common approach and takes a couple of minutes.
- Insert the photo. Tap Actions (the wrench) > Add > Insert a photo, then fit it to the canvas.
- Desaturate a duplicate. Swipe left on the photo layer and tap Duplicate. On the new layer, open Adjustments (the magic wand) > Hue, Saturation, Brightness and pull Saturation to zero.
- Duplicate again. Duplicate the desaturated layer so you have two identical grayscale layers.
- Invert the top copy. On the top layer, open Adjustments > Curves and drag the curve's endpoints so the line runs downhill (black point to the top left, white point to the bottom right). The layer now looks like a photographic negative.
- Switch to Color Dodge. Tap the "N" on the top layer, open the Lighten tab, and choose Color Dodge. The canvas goes almost entirely white. That is expected.
- Blur to reveal the lines. With the top layer selected, go to Adjustments > Gaussian Blur and slide your finger or pencil across the canvas. Edges appear as the blur increases.
Stop when the lines read clearly without turning into a muddy sketch. Low blur gives fine, delicate lines. Higher blur gives heavier, simpler contours.
Method 2: Blur and Divide
This variation skips the inversion and often gives a cleaner, more pencil-like result.
- Insert the photo and duplicate it. Hide the original so you keep an untouched copy.
- Desaturate the duplicate with Hue, Saturation, Brightness. A small brightness adjustment can help if the photo is flat.
- Duplicate the desaturated layer.
- Set the top layer's blend mode to Divide. The canvas goes white.
- Apply Gaussian Blur to the top layer. Low single-digit percentages are a sensible starting range for most photos, and you can adjust from there.
- Merge the two layers with Merge Down.
- Open Curves on the merged layer and drag the black point to the right. This deepens the lines and clears gray noise from the paper area. Pulling the white point slightly left also helps, but go lightly.
If you have two different blur values in mind, duplicate the finished layer first and compare them side by side before committing.
Tuning the Result
Most failed attempts come from a few predictable issues.
- You get a high-contrast black-and-white photo, not lines. You skipped or misapplied the blur. Make sure Gaussian Blur is applied to the top layer, not the bottom one, and that the blend mode is actually set.
- The canvas shows a yellow or colored cast instead of white. The source layers may not have been fully desaturated before the invert or dodge step. Bring Saturation to zero on the layer you duplicate.
- The line weight is wrong. Blur radius controls line thickness. More blur gives bolder, softer lines. Less gives finer detail and more noise.
- The result is noisy or grainy. Noisy photos produce noisy lines. Apply a small blur to the grayscale layer first, or choose a cleaner source. Curves can then push mid-grays to white.
- The look changes when you change canvas size. The same blur setting can look different on a small canvas than on a large one, so settle on your final resolution before tuning.
Source choice matters more than any setting. Photos with clear subject separation, even lighting, and strong edges convert best. Heavily textured scenes, such as foliage or fabric, produce a lot of line clutter.
Method 3: Trace for Deliberate Linework
When you need controlled, intentional lines rather than a filtered look, trace instead of converting.
- Insert the photo and reduce its layer opacity to roughly 30 to 40 percent so it works as a guide.
- Create a new layer above it and pick a brush with good pressure response, such as a monoline or technical pen.
- Use your brush's stabilization settings to smooth your strokes for confident curves.
- Trace the major contours first, then add interior detail. Use separate layers for different elements so you can adjust them independently.
- Hide the photo when you are done.
This is slower but gives you clean, varied line weight and decisions you can defend. For character work, product outlines, or logos, it usually beats a filtered result.
Coloring Under the Line Art
Filtered line art comes with a white background baked in. To paint beneath it, set the line layer's blend mode to Multiply. White drops out and the lines stay dark. Then add a new layer below the line layer and paint or fill there. Darken-group alternatives like Linear Burn or Color Burn give slightly different line density, so try them if Multiply looks too light.
Getting the Line Art Into After Effects
If this art is going into a motion pipeline, treat the export as a handoff.
- Export at final resolution. Raster lines will soften if you scale up in comp, so build the Procreate canvas at the size you need.
- Pick the right format. Export a PNG for stills. If you need transparent lines, either keep the line art on a transparent layer before exporting (when tracing), or export the white-background version and handle it in comp.
- Remove the white in comp. In After Effects, set the line layer to Multiply over your background. This lets you recolor the lines, animate them, or add glow.
- Keep layers separate. Export the line layer, color layer, and background as separate files so you can retime, offset, or add parallax in After Effects, Nuke, or Cinema 4D.
- Animating the look. Running the blend-mode conversion on a sequence of photos frame by frame can produce line boil and inconsistent thresholds, because each frame's blur and contrast responds to its own content.
When the Shot Is Moving: Where Styleframe Fits
Procreate's blend-mode trick is a good tool for a single still. It does not scale well to footage, because every frame is converted independently and nothing keeps the line style consistent over time.
For video, a reference-driven approach is a better fit than converting each frame on its own. is one tool to evaluate for that kind of work. Check its current features and export options before building a pipeline around it.
A practical workflow might be: build a hero line-art frame in Procreate using the techniques above, then use it as a style reference in a video stylization tool to carry that look across a clip. You keep your existing comp, color, and delivery pipeline and use the stylization tool for that one step.
Quick Reference
Start with Method 2 on a high-contrast photo, tune the blur and Curves until the lines read well, and save the layer stack so you can revisit settings later. Then decide whether the piece needs hand-traced lines or a filtered look, and export at the resolution your comp requires.