How to Turn a Photo Into a Sketch Procreate
StyleFrame Team7 min read
To turn a photo into a sketch in Procreate, import the photo, duplicate it, desaturate the copy, duplicate again, set the top layer to Divide (or invert it and use Color Dodge), then add Gaussian Blur until pencil-like lines appear. The whole process takes a few minutes and uses only built-in Adjustments and layer blend modes. It gives you a bitmap sketch you can color, paint over, or export as a still for a motion pipeline.
How the Procreate Photo-to-Sketch Technique Works
Procreate has no one-tap "convert to line art" command, so the method fakes edge detection with a blend-mode trick. You stack a blurred copy of the photo over a sharp copy and divide one by the other. Where the two layers match, the result goes white. Where tone changes quickly, such as edges, the result stays dark. That is why the blur amount controls how much "pencil" shows up: more blur reveals more of the image.
Understanding this makes troubleshooting much easier. Every variation you'll find, whether Divide or Color Dodge with an inverted layer, is a different route to the same stack: a grayscale base plus a blurred, blend-moded copy.
Step-by-Step: Photo to Pencil Sketch
1. Import the photo
Tap Actions (wrench) → Add → Insert a photo. Choose your image and scale it to fill the canvas. Fitting the canvas isn't required, but it saves cropping later. You can also start a project directly from the Gallery by importing the photo.
2. Duplicate and keep the original safe
Swipe left on the photo layer in the Layers panel and tap Duplicate. Hide the bottom layer so the untouched photo stays available for color work later.
3. Desaturate the copy
Select the duplicate, open Adjustments (magic wand) → Hue, Saturation, Brightness, and drag Saturation to zero. A small brightness adjustment here can help if the source is flat or very dark.
4. Duplicate the grayscale layer
Duplicate the desaturated layer so you have two identical grayscale layers stacked.
5. Set the blend mode to Divide
Tap the N on the top grayscale layer and choose Divide. The canvas will look blank or nearly white. That is expected at this stage.
6. Blur to reveal the lines
With the top layer still selected, go to Adjustments → Gaussian Blur, then slide your finger across the canvas. As the blur rises, sketch lines emerge. Values around 5% are a reasonable starting point for line-art looks, while softer, shaded pencil looks often sit higher, around the low teens. Results vary from image to image, so judge by eye.
7. Merge and refine
Tap the top layer and choose Merge Down if you want a single flattened sketch layer. Then open Adjustments → Curves to adjust contrast. Pull the bottom-left point to the right to deepen the darks, and nudge the top point slightly left to clean up the whites. Go easy, because pushing the curve too far starts inverting or crushing the image.
The Color Dodge Variation
An older version of this technique reaches the same result differently:
- Duplicate the photo and desaturate it.
- Duplicate that grayscale layer.
- Open Curves on the top copy and reverse the curve so the image inverts.
- Set that inverted layer to Color Dodge (in the Lighten tab of the blend menu). The canvas will turn white.
- Apply Gaussian Blur until the lines appear.
Divide is a bit simpler because it skips the inversion step. Color Dodge can give slightly different tonal behavior, so it's worth trying both on the same image.
Troubleshooting Common Problems
You only see a high-contrast black-and-white photo. The blur hasn't been applied to the correct layer, or the blend mode isn't set on the top layer. Check that the blurred layer is the one using Divide or Color Dodge.
The canvas turns yellow or tinted instead of white. Check that the layer was fully desaturated before the blend step. Return to the Hue, Saturation, Brightness adjustment and confirm saturation is at zero.
You can't find the blend mode. Tap the small letter (usually N) on the layer thumbnail. Color Dodge sits in the Lighten tab along the bottom row of tabs, and you can scroll the menu to find Divide.
Lines look muddy or too faint. Reduce the blur slightly, then use Curves to deepen the darks. Source image contrast matters a lot, so a flat photo may need a brightness or contrast adjustment before you begin.
Making a Colored Sketch Instead
If you want the pencil lines over color, start with the same grayscale-plus-Divide-plus-blur stack, then:
- Hide the middle layer (or delete it).
- Duplicate the original color photo and move the copy to the top of the stack.
- Set that copy's blend mode to Overlay.
- Optionally duplicate that layer again to intensify color.
Another route is to paint under the line art. Set the sketch layer to Multiply (or Linear Burn, Color Burn, or Darker Color) so its whites become transparent, then add a new layer beneath it and color there. Multiply is usually the cleanest starting point, but the differences between these modes are subtle, so test a couple.
Where Procreate's Method Falls Short
This technique is a workaround, not true line extraction. A few practical limits matter if you're coming from a production background:
- Edges are softer than filter-based results. Photoshop's Find Edges filter produces a sharper outcome than the Procreate blur trick, so don't expect crisp, uniform contours.
- Output is bitmap only. Procreate doesn't create vector lines, so scaling up means resampling.
- It's one frame at a time. The workflow is manual and per-image. Applying it across a shot's worth of frames isn't something you'd want to do by hand.
- Parameters aren't consistent across images. The blur value that looks right on one photo can wash out another, so a series of photos may each need individual tuning.
- Tracing is the alternative. If you want clean, stylized lines, many artists import the photo, lower its opacity, and trace by hand on a new layer. That produces more intentional results but takes far longer.
For concept art, reference, and single illustrations, those limits are acceptable. For motion work, they matter more.
Bringing a Procreate Sketch into a Motion Pipeline
If you're an animator or motion designer, a Procreate sketch can serve as a style reference, a background plate, or a texture element. A typical handoff looks like this:
- Export the sketch layer as an image file (if you used Multiply and a separate color layer, export the layers individually).
- Import it into After Effects and place it above your footage or color plate.
- Set the layer's blend mode to Multiply in the timeline, matching what you did in Procreate.
- Add a displacement or edge-roughening effect, or time-remap through several hand-drawn variations, to make the lines boil like traditional animation.
- Use the same asset in other compositing or 3D tools as a texture or compositing element.
The weak point is moving from a single sketched still to a sequence. Doing that frame by frame in Procreate is tedious, and a fixed filter stack applied to video may flicker.
Quick Recap
- In Procreate: import, duplicate, desaturate, duplicate, set Divide, blur, then refine with Curves.
- Color Dodge with an inverted layer is a valid alternative route to the same effect.
- Most failures come from the wrong layer being blurred, incomplete desaturation, or the blend mode being applied to the wrong layer.
- Procreate's result is a soft, bitmap approximation of line art, which is fine for stills and reference but limited for sequences.
- For motion, use your Procreate sketch as a style reference rather than repeating the process frame by frame.