How to Turn a Drawing Into a Brush Procreate
StyleFrame Team6 min read
To turn a drawing into a Procreate brush, draw it on a square canvas in white on black (or black on white), export it as a JPG, then open Brush Studio and import it as the Shape Source of a duplicated or new brush. Procreate reads the image as grayscale: white is opaque and black is transparent, so invert the image if your brush paints a blank square or the design appears negative. Then raise the spacing, turn on Orient to iPad Screen if you want the stamp to stay upright, and save the brush. Procreate brushes cannot hold full-color images, so color detail has to come from the brush's color settings or from a different workflow.
How Procreate reads a drawing as a brush
A Procreate brush has two image slots, and picking the right one decides whether your drawing behaves like a stamp or a texture.
- Shape is the footprint of the brush, like a rubber stamp. A drawing of a leaf, a star, or a hand-inked ornament belongs here.
- Grain is a texture applied inside that footprint, like paper tooth or sponge marks. A scan of bark, watercolor, or grit belongs here.
The key limit is that both slots only interpret brightness. Procreate converts whatever you import to grayscale values: white paints, black doesn't, and grays produce partial transparency. That is why a detailed color illustration can't become a full-color stamp. You get a one-color silhouette with tonal variation, and you paint it in whatever color is active.
For an artist coming from compositing, think of the imported image as a luma matte. The brush then fills that matte with your current color.
Step-by-step: drawing to brush
1. Prepare the drawing on a square canvas
Create a square canvas. 2048 × 2048 px works as a standard starting point. Non-square sources get distorted, and small sources turn soft when the brush is scaled up. If you plan to use the stamp at large sizes, work bigger.
Set the background to black and draw in white, or draw in black on white and invert later. Keep it pure black and white if you want a crisp, fully opaque stamp. Soft grays create a semi-transparent, shaded result, which is useful for textured or painterly stamps but unwanted for a clean logo or glyph.
Leave a margin around the artwork so the edges of the design don't clip at the boundary of the square.
2. Export or copy the image
You have two routes:
- Export as JPG. Use Share in the Actions menu and save to Photos. JPG is the safest format because it has a solid background.
- Copy the canvas. Copy the whole canvas to the clipboard and paste it straight into the brush's shape or grain source. This is the fastest route when you iterate: draw, paste, test, repeat.
3. Create or duplicate a brush
Open the brush library and either tap the plus icon to start a new brush or swipe left on an existing stamp-style brush and choose Duplicate. Duplicating is often smarter, since you inherit sensible dynamics instead of default settings. It also keeps your custom brushes out of the stock sets if you create your own brush set first (tap the plus at the top of the set list).
4. Import the drawing as the Shape Source
In Brush Studio:
- Open Shape.
- Tap Edit in the Shape Source panel.
- Tap Import and choose Photos or Paste, depending on where your image lives. The built-in Source Library is there too if you want a starting shape.
- Check the preview. If your drawing appears as a hole in a white square, two-finger tap the editor to invert it.
- Tap Done.
5. Tune the stroke path
A drawing imported as a shape will smear into a ribbon until you change the spacing. Open Stroke Path and raise Spacing so each stamp lands as a distinct copy. Lower spacing gives a continuous line made of overlapping copies. Useful companions:
- Jitter scatters stamps off the path, handy for foliage, confetti, or stars.
- Falloff makes the paint run out over the length of a stroke.
Under General, switch on Orient to iPad Screen if you want a stamp that always stays upright rather than rotating with your stroke direction.
6. Set a grain, test, and save
If you want the stamp solid, pick a plain white grain source so no texture interferes. Use the drawing pad at the side of Brush Studio to test strokes as you change settings, then tap Done and name the brush. You can reopen it any time to refine it.
Troubleshooting a brush that won't work
The brush is blank. This is a common issue. If your design is black on a transparent PNG, Procreate reads the transparent background as black and the design as black, so the whole image becomes "nothing." Fix it by drawing in white, placing black artwork over a solid white background, or exporting as JPG. Then invert with a two-finger tap if needed.
The stamp looks blurry. The source was too small. Rebuild it at a larger canvas size.
The stamp is stretched or squashed. The source wasn't square. Re-crop to 1:1.
The stamp is faint or see-through. Your artwork contains grays. Increase contrast with Curves or redraw in pure white.
It still paints a rectangle. You may have imported the image into Grain instead of Shape, or the background isn't fully black. Check both slots.
You wanted color. Procreate won't carry the original colors. Options include using the brush as a one-color stamp and recoloring on a separate layer, using color dynamics for variation, or pasting copies of the artwork directly as layers.
Shape or grain: choosing the slot
Use Shape when you want discrete, repeatable objects: leaves, scales, stars, textured blobs, hand-drawn icons. Use Grain when you want texture to show inside any stroke, such as scanned ink, sponge marks, or paper fiber. Some artists mix both: a rough scanned blob as the shape, and a photographed paper texture as the grain, set to repeat so its edges don't show.
Scatter-style brushes, where the same element repeats at varied sizes, are just a stamp shape with spacing, jitter, and size variation turned up. They save you from redrawing the same tree or leaf dozens of times.
Quick checklist
- Square canvas, large size, pure black and white for solid stamps.
- White paints, black hides; invert with a two-finger tap if it looks wrong.
- Export as JPG, or paste from the clipboard to iterate faster.
- Import into Shape for stamps, Grain for textures.
- Increase spacing and adjust jitter for distinct repeated marks.
- Expect grayscale behavior; plan another route for full-color art.
Once the first stamp works, the quickest way to get better is to save a few variations and compare them stroke by stroke, adjusting one setting at a time.