How to Trace Smooth Curved Lines While Tracing in Procreate
StyleFrame Team7 min read
To trace smooth curves in Procreate, put your reference on its own layer at low opacity, draw on a separate layer above it, and set StreamLine and Stabilization in Brush Studio for the brush you're using. Draw each curve in one confident stroke from the shoulder rather than the wrist, rotate the canvas so every arc pulls toward your body, and break strokes only at natural inflection points. For straight segments, hold at the end of a stroke and Procreate will snap it into a straight line.
Set Up the Canvas Before You Trace
Smooth tracing starts with a setup that keeps the reference out of your way.
- Open the Actions menu (wrench), choose Add, then Insert a photo, and place your reference on the canvas.
- Lower that layer's opacity until you can see it clearly but your new strokes still stand out. Somewhere between 30 and 50 percent usually works.
- Lock or rename the reference layer so you never draw on it by mistake.
- Create a new empty layer above it for line work.
If you work from video frames, storyboards, or a rough animatic, this is the same logic as a guide layer in After Effects. The reference is there to be read, not to be touched.
It also helps to turn on layer select under Prefs > Gesture Controls. That way you can tap with the Pencil to jump to the right layer rather than hunting through the panel when a stroke lands in the wrong place.
Tune Stabilization the Right Way
Most wobble comes from settings, not from your hand. Procreate gives you smoothing in two places, and they behave differently.
Brush-Level Settings
Tap a brush twice to open Brush Studio, then go to Stabilization. You will find a few controls:
- StreamLine: Pulls your stroke toward a smoothed path as you draw. This is the main control for long, flowing curves. Higher values give cleaner arcs.
- Stabilization: Smooths and straightens your stroke. It is excellent for sweeping contours and less good for small, tight details.
Duplicate the brush before you edit it, so you keep an untouched original and a dedicated tracing brush. If you ever make a mess of the settings, the About this Brush tab lets you reset the brush.
Global Smoothing
Under Actions > Prefs > Pressure and Smoothing, you can apply stabilization to every brush at once. That is convenient for a long tracing session, but it is also the most common reason the Pencil suddenly feels laggy in a later project. Treat it like a temporary override and turn it back down when the tracing job ends.
Know When to Dial It Back
High smoothing rounds off corners. If your reference has hard edges, such as a logo with sharp points or a mechanical part, drop StreamLine for those passes and use a lower-smoothing duplicate of the brush.
Draw Curves With Your Whole Arm
Software settings can only clean up what you give them. A few physical habits make a visible difference.
- Draw from the shoulder and elbow. Wrist-driven strokes tend to produce tight, uneven arcs. Longer arm movement makes the curvature more consistent.
- Rotate the canvas constantly. Use two fingers to turn the canvas so each curve bends toward your body. Most people draw their cleanest arcs in one or two directions, so let the canvas adapt to your hand.
- Zoom out a little. When you are zoomed in tight, a small hand tremor is magnified across the screen. Working at a moderate zoom often yields smoother results, and you can zoom in afterward to refine endpoints.
- Commit to the stroke. Slow, hesitant strokes pick up every tremor. A quick, confident pass followed by an undo (two-finger tap) beats a careful one that shakes.
- Warm up first. A minute of loose arcs and ovals in a scratch layer gets your hand moving the way you need it to.
Break Complex Shapes Into Clean Segments
Trying to trace a whole silhouette in one stroke usually backfires. Instead, look at the reference and find where the curvature changes direction. Those inflection points are the natural places to lift the Pencil.
- Trace each curve as its own stroke, starting and ending at a point where the shape changes.
- Overlap the end of one stroke with the start of the next by a few pixels, so the joint stays continuous.
- Keep strokes tangent at the joints. If the first curve exits heading up and right, the next should enter at the same angle.
- Use long strokes for large forms and save short strokes for details.
You can clean up the overlaps afterward with the eraser at a hard setting, or by selecting a stray end and nudging it with the Transform tool.
Use Hold-to-Snap for Straight Segments
For straight edges, let Procreate do the work. Draw a line and hold the Pencil at the end of the stroke, and Procreate turns it into a straight line. Putting a finger on the screen while you hold locks the line in place.
This works especially well for any part of an outline that is supposed to look machine-clean.
Fix Problem Areas Without Redrawing
Even good tracing leaves a few rough spots. Fix them selectively.
- Selection tool with Freehand mode: Select a wobbly section, then move or reshape it with the Transform tool. Use Distort or Warp for subtle bends.
- Liquify: Push and pull a line gently. Keep the size large and the pressure low, so you smooth the curve instead of creating new bumps.
- Eraser plus redraw: For short sections, it is often faster to erase the stretch between two clean points and redraw it in one stroke.
- Lower the reference opacity further: Sometimes the line looks bad only because the reference underneath is distracting. Hide it and judge the curve on its own.
Prepare Procreate Line Art for After Effects
Many motion designers trace in Procreate because the pen feel is better than a mouse, then bring the result into a timeline. A few choices at this stage save time later.
- Export clean layers. Put line work on its own layer with a transparent background and export it as an image. Keep the canvas large enough for your composition resolution.
- Match the canvas size to your comp. Scaling up a low-resolution trace softens the edges and makes any wobble more obvious.
- Convert to vectors if you need to animate the paths. Procreate layers are raster, so a common route is to run the artwork through a vector-tracing tool, then convert the result to shape layers in After Effects. Smooth, consistent strokes with solid contrast produce cleaner paths with fewer anchor points, which is why the smoothing work above pays off here.
- Keep a version with no smoothing artifacts. If you plan to use Trim Paths or Repeaters, check that curves remain continuous at the joints between strokes.
Raster line art can also stay raster. Plenty of 2D animators use hand-drawn frames from Procreate directly as image sequences or frame-by-frame layers.
Where Styleframe Fits After the Trace
Once you have a clean set of traced line drawings, you may want to push them further without redrawing every frame. Styleframe is an AI video and motion tool that can sit after the Procreate stage in a pipeline, using your traced drawings as reference material.
The workflow stays reference-driven, so you can iterate on a look without losing the original trace. It complements hand tracing rather than replacing it, since the quality of the line drawing still sets the ceiling for what comes out.
A Quick Checklist for Smooth Traced Curves
- Reference on its own layer at reduced opacity, with a separate drawing layer above
- A duplicated tracing brush with StreamLine and Stabilization set to taste
- Global smoothing used sparingly and reset afterward
- Long, confident strokes drawn from the shoulder, with the canvas rotated for every arc
- Strokes broken at inflection points, with tangent overlaps
- Hold-to-snap for straight segments
- Liquify, Warp, and selective erasing for cleanup
- Exports sized to your composition, ready for vector tracing if you need paths
Smooth lines come from a few repeatable habits more than from talent: the right brush settings, a comfortable canvas angle, and strokes that follow the shape's real curvature. Set those up once, save the brush, and every tracing job gets faster.