How to Take Background Out of Picture Procreate
StyleFrame Team7 min read
Procreate has no single "remove background" button, so you build the cutout with the Selection tool. Choose Automatic to tap and remove flat or white backgrounds, or Freehand to trace the subject you want to keep. Then delete the unwanted area with Cut, Clear, or a layer mask. A mask is the better choice for production work because it is non-destructive. Export the result as a PNG to keep the transparency.
Which Procreate method should you use?
Prep before you cut anything
A few habits will save you from redoing work.
- Duplicate the layer. Duplicate the image layer, then hide the original. If a selection goes wrong, the untouched source is still there.
- Hide the canvas background color layer. Procreate's default white background layer sits under your image. If it stays visible, you won't see transparency, and it's easy to think the cut failed.
- Check canvas size. If the cutout is headed for print or a high-resolution comp, set the canvas to the final pixel dimensions before you import. Upscaling a cutout later softens the edges you just worked on. For print, 300 DPI at the target size is the usual baseline.
- Zoom in. Selections made at fit-to-screen zoom are rough. Pinch in close on edges, especially hair, fur, and fine props.
Method 1: Automatic Selection for flat backgrounds
This is the fastest route when the background is a uniform color, such as a white sheet of paper, a scanned sketch, or a product on seamless backdrop.
- Open the Selection tool (the S icon in the toolbar).
- At the bottom, choose Automatic and make sure Add mode is on.
- Tap the background area of the image layer.
- Keep your pencil or finger held down after the tap, then drag left or right. This changes the selection threshold. Drag until the marching ants hug the subject without eating into it.
- Tap the wrench (Actions) icon and choose Cut, or use the three-finger swipe down and tap Cut. You can also swipe three fingers left and right on the canvas to clear the selection.
- Hide any layers beneath to confirm the area is transparent.
One quirk catches many beginners. If the whole picture disappears, the selection probably included the subject, or you cleared the wrong layer. Undo with a two-finger tap, confirm the right layer is active, and re-run the selection at a lower threshold.
Automatic Selection works on color similarity, so it struggles with watercolor textures or backgrounds that share tones with the subject. You don't need a perfect first pass. Remove most of the background, then clean up the rest by hand.
Method 2: Freehand Selection for photos and complex subjects
When the background isn't a single color, trace the subject yourself.
- Open the Selection tool and choose Freehand with Add mode.
- Zoom in and start at a clear point on the subject's edge.
- Trace around the subject. For straight-edged objects, tap points to create straight segments. For organic shapes, draw continuously.
- Close the loop by returning to your starting point and tapping the dot. Alternatively, leave the loop open and lift your pencil, which still closes the selection.
- Tap Invert so the background is selected instead of the subject.
- Cut or clear the selected area.
A few practical notes:
- Closing the selection makes the outline lines vanish. That's expected. The selection is complete.
- If you tap the dot and the selection seems to turn the image black or white, undo with a two-finger tap and your traced area returns.
- To subtract from a selection, switch to Remove mode before adding a new shape, which is useful for holes such as the gap between an arm and a torso.
- For rough blocking, the Rectangle and Ellipse modes in Selection speed up the first pass. Use them to remove large background areas, then switch to Freehand for the detail.
Method 3: Layer Mask for a non-destructive cutout
If you may need to adjust the edge later, mask the layer instead of deleting pixels.
- Make a Freehand or Automatic selection of the part you want to keep.
- Open the Layers panel and tap the image layer.
- Choose Mask from the menu. Procreate applies a mask based on your selection.
- Tap the mask thumbnail to edit it. Paint with black to hide more of the image and white to reveal it.
With a mask, the source pixels remain intact and the edge is editable. If a client decides they want the shadow back or a slightly looser crop, you paint it in rather than starting over. Keep the mask layer and the source together while you work, and pinch them to merge only when you're sure you're done.
Clean up the edges
Even a good selection leaves artifacts, so plan a cleanup pass.
- Speckles and leftover fringe: Use the Eraser with a hard-edged brush for crisp removals. A soft brush leaves semi-transparent haze that shows up when you composite over dark backgrounds.
- Halos: If the original background was white and the subject has soft edges, light fringing often remains. Check your cutout against a dark layer. Place a solid dark fill beneath it and zoom in to spot light pixels.
- Jagged edges: A slightly soft eraser pass along the edge, or a small blur on the mask, can help it sit better in a comp. Test it over the real background you'll use.
- Stray content: Fingers, shadows, or paper edges at the border often need manual removal.
Isolate a single element from a sheet
For sticker sheets or illustration pages, the process is a short variation. Remove the background, then use Freehand to loosely draw around one element. Use Copy & Paste to place it on its own layer, hide the original sheet, and reposition. This gives you separate assets without redrawing anything.
Export so the transparency survives
Transparency only survives in formats that support it.
- Open Actions, then Share.
- Choose PNG. JPEG flattens to a solid background and loses your cutout.
- In your compositing software, drop the PNG into your timeline and check the edge over your actual background. If a light or dark fringe appears, treat it in the comp, or re-export with a slightly tightened edge.
If you're sending sequences or stills to a compositor, name layers and files clearly and agree on resolution before you start.
Common problems and fixes
- "Nothing happens when I cut." Make sure the right layer is active and a selection is actually present.
- "The background looks removed but there's still white." Your canvas background layer is visible. Toggle it off.
- "Automatic grabs part of my subject." Lower the threshold by dragging after the tap, or switch to Freehand for that region.
- "The edge looks rough at 100%." Redo the selection at higher zoom, or switch to a mask and refine the edge by hand.
- "My circular image shows a square when printed." Transparency doesn't help if the print workflow flattens it. Export with the shape you need, or crop to the shape in the destination layout application.
Where Procreate stops and a motion pipeline starts
Procreate is excellent for stills, illustration, and quick cutouts. It's less suited when you need many cutouts, consistent edges across a series, or isolation of subjects in motion. For video, you'll generally want rotoscoping tools built to work on time-based footage.
For AI-assisted work, is one option to explore when the cutout is part of a larger sequence.
A realistic split looks like this: use Procreate when you're painting or hand-tracing a single illustration, and look to a motion-focused tool when the cutout is part of a larger sequence. In both cases, inspect the matte edge over your final background before you commit.
Quick checklist
- Duplicate the layer and hide the original.
- Hide the canvas background color.
- Choose Automatic for flat backgrounds and Freehand for complex ones.
- Use a mask if you want to adjust the edge later.
- Clean speckles with a hard eraser.
- Check the edge over dark and light backgrounds.
- Export as PNG to preserve transparency.
Once you've run through this a few times, the mask-based version leaves you room to fix edges without starting over.