How to Straighten Lines in Procreate
StyleFrame Team6 min read
To straighten a line in Procreate, draw it and keep your Apple Pencil or finger on the screen at the end of the stroke. After a brief pause the line snaps straight (QuickLine), and touching a second finger to the screen while holding locks the angle to 15° increments. The same hold-at-the-end gesture cleans up circles, rectangles, and triangles (QuickShape), and a notification at the top of the canvas lets you edit the result. For strokes you've already drawn, rotate them with Transform, or use a Drawing Guide with Assisted Drawing so every new stroke follows the guide.
Method 1: QuickLine for instant straight lines
QuickLine is the fastest option and needs no setup.
- Select a brush (or the eraser) and start a stroke on a layer.
- Drag in roughly the direction you want, then stop moving without lifting.
- Hold for a moment. The wobbly stroke straightens between your start and end points.
- While still holding, move your pencil to adjust the angle and length.
- Optionally, touch a second finger to the canvas. The angle now snaps in 15° steps, which makes true horizontals, verticals, and 45° diagonals easy.
- Lift to commit.
If the snap fires too early or too late, go to Actions (wrench) > Prefs > Gesture Controls and open the QuickShape settings. You can change the hold delay or turn the behavior off. A shorter delay is faster but triggers accidental snaps on slow, deliberate strokes. A longer one forgives hesitation but slows your rhythm.
Method 2: QuickShape for rectangles, circles, and polylines
QuickShape uses the same hold gesture on closed or multi-segment shapes. Sketch a rough rectangle, triangle, circle, or a polyline of connected segments, then hold at the end of the stroke. Procreate replaces your hand-drawn shape with a clean one, and you can keep dragging to change its size and orientation before lifting.
With the shape still held, a second finger makes it more regular: a triangle gets equal sides, and a rough ellipse becomes a true circle.
Editing a QuickShape
Right after the snap, a notification appears at the top of the canvas. Tap it to open the edit shape menu, where you can:
- Switch the shape type, for example from circle to square.
- Use the transformation nodes around the shape for fine adjustments.
This window is short. Once you start another action, the edit menu is gone, and you'll need the Transform tool to modify the shape.
Method 3: Straighten an existing stroke with Transform
QuickLine only works while you're drawing. If a line is already on the canvas and is slightly tilted, fix it with Transform instead of redrawing.
- Put the line on its own layer.
- Tap the Transform (arrow) icon.
- Rotate the line until it sits level.
- Tap Transform again to confirm.
This is also how you correct a QuickShape after the edit window has closed.
Method 4: Drawing Guide and Assisted Drawing
When you need many lines to be straight and consistent, such as architecture, UI mockups, or storyboard panels, a guide is more reliable than snapping line by line.
- Open Actions > Canvas and toggle Drawing Guide on.
- Tap Edit Drawing Guide.
- Turn on Assisted Drawing so your strokes conform to the guide rather than only displaying it.
Assisted Drawing can be enabled per layer, which is useful: a layer marked Assisted constrains your strokes, and a layer without it stays freehand. Keep guided linework on one layer and loose sketching on another, and you can switch between modes without changing global settings.
Method 5: Stabilization to calm shaky lines
Sometimes you don't need perfectly straight lines, just lines without the tremor. Procreate smooths strokes in two places.
- Global stabilization is under Actions > Prefs > Pressure & Smoothing. It applies to every brush. Start low, around 10–15%, and increase it only as far as you need.
- Brush-level stabilization is in the Brush Studio under the Stabilization tab. The Stabilization amount smooths and straightens the stroke, and StreamLine reduces wobble and shake. Duplicate a brush before editing it so you can always return to the original. If you do change something, About this Brush > Reset Brush restores the defaults.
High stabilization adds lag. If your pencil feels sluggish or unresponsive, check the global slider first. Turn it down for gestural work, texture, and sharp corners, where you want the stroke to follow your hand.
Fixing lines that are too straight
A common complaint is the opposite problem: every stroke comes out as a rigid straight line. The cause is usually one of these:
- Assisted Drawing is still on. Go to Actions > Prefs > Gesture Controls > Assisted Drawing and turn off Apple Pencil (and Touch if enabled). This setting can keep constraining strokes to a guide even after you've hidden the Drawing Guide.
- The layer is marked Assisted. Look for the Assisted label on the layer thumbnail, tap the thumbnail, and toggle Drawing Assist off.
- A Drawing Guide is still active. In Actions > Canvas, turn off the guide, or open Edit Drawing Guide and disable Assisted Drawing there.
- Stabilization is stuck high. If strokes seem to drag toward a straight path and no shape notification appears, it isn't QuickShape. Check brush stabilization, then Prefs > Pressure & Smoothing and tap Reset.
- QuickShape triggers by accident. Increase the hold delay or disable it in Gesture Controls.
A quick diagnostic: if a notification appears at the top of the screen when the line snaps, it's QuickShape. If there's no notification, check Assisted Drawing and stabilization.
Practical habits for cleaner lines
- Rotate the canvas. Turn the canvas so the stroke runs in the direction your hand moves most comfortably, instead of forcing awkward angles.
- Warm up first. A few quick ovals, arcs, and hatch lines loosen your hand before detailed linework.
- Separate layers by purpose. Keep construction lines, guided lines, and final ink apart so you can straighten, transform, or delete one without touching the rest.
Where straightened linework goes next: motion pipelines
For motion designers, animators, and VFX artists, Procreate can be used for concept art, storyboards, style frames, and hand-drawn elements. Clean, straight construction lines matter there because they carry into layout, camera moves, and compositing, where a crooked horizon or skewed edge shows up immediately once things move.
A typical handoff looks like this:
- Draw and straighten key frames in Procreate using QuickLine, Transform, or a Drawing Guide.
- Export the frames at the resolution your comp needs.
- Bring them into your compositing, editing, or 3D software.
One practical tip: finalize line corrections in Procreate before sending frames onward.
Quick reference
Summary
Procreate gives you several ways to straighten lines, each suited to a different situation. Use QuickLine and QuickShape for speed, Transform for correcting existing work, Drawing Guides for consistent geometry, and stabilization for steadier freehand strokes. If your lines are snapping when you don't want them to, the culprit is often Assisted Drawing or a stabilization setting, and both are quick to reset. Get the structure right at the source, and it will carry cleanly into whatever motion pipeline comes next.