How to Start a Blueprint of a Home on Procreate
StyleFrame Team7 min read
To start a blueprint of a home in Procreate, create a canvas at a real paper size such as A3 (420 × 297 mm), turn on the 2D Grid Drawing Guide, and set the grid spacing to 1 cm. At a 1:100 scale, each square then equals 1 metre. Set the background to blue, draw the outer walls on their own layer with a fine-tip brush and Drawing Assist on, and add interior walls, openings, and dimensions on separate layers.
Decide the scale and gather measurements first
Scale is the one decision that is hard to change later. Before you open Procreate, answer three questions:
- How big is the building? A compact house of roughly 12 × 9 m fits comfortably on A3 at 1:100 and leaves room for notes. At 1:50 the same house fills the sheet and shows more detail.
- What units will you think in? Metric is easier on a 1 cm grid because the arithmetic stays clean. Imperial works too, but you will need to pick a grid value that maps to feet, and the math gets fiddly.
- Where do your dimensions come from? Use a survey, an existing plan, a laser measure, or your own site notes. If you are designing a small space or furniture layout, the iPad's Measure app can capture rough sizes. Write the numbers down before you draw.
Procreate is iPad-only. It was sold as a one-time purchase at the time of the research (listed at $12.99), but check the App Store for current pricing.
Step 1: Create the canvas
From the Gallery, tap the plus icon and choose a custom canvas. Set the width and height in millimetres, for example 420 × 297 for A3 landscape. Pick a DPI that matches your output. 300 DPI is a sensible default for print.
If the plan will end up in a video timeline, think about the final frame at this point. A 16:9 canvas such as 3840 × 2160 px may suit that workflow better than A3 paper. You can still use a scaled grid on it. You just define the scale relative to pixels instead of millimetres.
Step 2: Set up a scaled grid
Procreate's grid is a drawing aid, not a measuring tool, so you have to tell it what each square means.
- Tap the wrench (Actions) → Canvas → toggle Drawing Guide on.
- Tap Edit Drawing Guide.
- Choose the 2D Grid and adjust the grid size. On a millimetre canvas, you can set it to 10 mm.
- Adjust the grid's colour and size so it is visible but does not compete with your linework.
Now write the scale on the canvas as a note, for example "1 square = 1 m, 1:100". It sounds trivial, but it prevents the classic mistake of coming back to a file a week later and not remembering what the grid represents. Also draw a simple scale bar in a corner. If you ever resize or reuse the file, the bar scales with it.
Step 3: Give it the blueprint look
You have two reasonable approaches:
- Draw it blue from the start. Tap the Background Color layer in the Layers panel, choose a deep blue, and draw with a white or pale-cyan brush. This shows you the final look as you work.
- Draw dark on light, then invert. Work in black on white for clarity, then invert the colours on a merged copy to get white lines on a dark ground and shift the colour to blue. This is useful if you want a clean black-and-white plan as well.
For the brush, choose something with a consistent, hard edge. A fine-tip inking brush from the Inking set works well. Avoid textured or pressure-heavy brushes for the structural layers, because they make walls look uneven and complicate any later tracing or vectorizing.
Step 4: Set up layers before you draw a line
A blueprint is a stack of information types. If everything lives on one layer, every change becomes a repair job. A practical structure, from bottom to top:
- Reference (imported plan, site photo, or sketch at low opacity)
- Site (boundary, setbacks, north arrow)
- Walls, exterior
- Walls, interior
- Openings (doors, windows, door swings)
- Fixtures and furniture
- Dimensions
- Labels and notes
Name each layer as you create it. This takes seconds and pays off when you have 20 layers and need to move a bathroom.
Step 5: Draw the site and exterior walls
Start with the largest, most certain geometry:
- Site boundary on the Site layer, if you have one. Use the grid to place the corners at the correct distances.
- Setback lines, if local rules apply. Draw them dashed or in a lighter tone so they read as constraints, not walls.
- Exterior walls as a closed shape on their own layer.
For straight lines, draw a stroke and hold your pencil at the end until QuickShape snaps it straight. Turn on Drawing Assist so strokes follow the active grid. Without Drawing Assist, long lines can come out slanted or curved. For walls with thickness, draw two parallel lines a fixed number of squares apart, or draw a single thick line and treat it as the wall centreline. Decide which convention you use and stay consistent.
Use Stabilization if your hand shakes on longer lines. Too little gives you wobble, while too much makes corners feel laggy.
Step 6: Add interior walls and openings
Block out rooms first, then refine. Keep to the grid for wall positions, and use real dimensions for the rooms that matter: a bedroom that fits a queen bed with circulation space, a bathroom that fits a standard fixture arrangement, a corridor wide enough to walk through. For doors, check standard widths for your region, as local codes vary.
On the Openings layer:
- Erase the wall segment where a door or window sits.
- Draw door leaves and swing arcs freehand over a grid reference.
- Mark windows with a double or triple line in the wall.
Working on separate layers means you can toggle openings off to check the wall geometry, or nudge a door without redrawing the wall.
Step 7: Add dimensions, labels, and finishing details
Place dimension lines on their own layer outside the building footprint, with small ticks at each end. Label key spans, such as overall width, overall depth, and major rooms. Add room names in a clear, consistent font, or hand-letter them for a more sketched feel.
Finally, add a north arrow, the scale note, and a title block. A plan without a scale and orientation looks like a sketch, no matter how clean the lines are.
If you are tracing an existing plan
For renovations or when you start from a brochure plan:
- Import the image (Actions → Add → Insert a photo) and place it on the Reference layer.
- Lower its opacity so your grid and new linework remain visible.
- Resize it until a known dimension, such as a labelled wall length or a standard door width, lines up with the correct number of grid squares.
- Trace on new layers, never on the reference.
Check at least two dimensions in different directions after scaling. If one is off, the image may be skewed from a photo or scan, and you should correct it before tracing.
Common mistakes to avoid
- Setting the grid after drawing. Changing the grid does not rescale existing strokes.
- Mixing scales. Furniture drawn at one scale and walls at another will look fine until you try to line up a sofa with a doorway.
- Using one layer. Revisions become destructive.
- Over-detailing early. Block out geometry before adding hatching, textures, or symbols.
- Trusting a photo of a plan. Perspective distortion silently ruins accuracy.
Taking the blueprint into a motion pipeline
If your blueprint is headed for a title sequence, an architectural walkthrough intro, or an explainer, export it with the pipeline in mind. Export layered files to keep walls, openings, and labels separate, or export each layer group as its own image, so each element can be animated individually in your compositing software.
Keep the engineering-accurate blueprint in Procreate or CAD, and use generative tools only for the presentation layer. The plan should remain the source of truth for measurements.
Quick-start checklist
- Pick the scale (1:50 or 1:100) and the paper or frame size.
- Create the canvas at real dimensions.
- Enable the 2D Grid and set each square to a known distance.
- Write the scale on the canvas and draw a scale bar.
- Set up named layers before drawing.
- Draw the site, exterior walls, interior walls, openings, then dimensions.
- Export layered files if the plan will be animated.
Once the first wall sits correctly on the grid, the rest of the drawing follows from the same logic.