How to Stabilize Pen in Procreate
StyleFrame Team7 min read
To stabilize your pen in Procreate, tap Actions (wrench) > Prefs > Pressure & Smoothing and raise the Stabilization slider to smooth every brush at once. To change a single brush, open it in Brush Studio and adjust its Stabilization tab. Start low, around 10-15% for global stabilization, and use StreamLine for wobble, Stabilization for straighter strokes, and Motion Filtering for sudden bumps.
What "stabilizing the pen" means in Procreate
Procreate builds a stroke by plotting many points along the path your Apple Pencil or finger travels. Stabilization changes how those points are processed before they reach the canvas. Rather than drawing every tremor, Procreate averages or filters the motion, so the line you see is cleaner than the line you actually drew.
There are two levels:
- Global stabilization overrides brush behavior across the whole app. Every stroke is smoothed, even with brushes not designed for it.
- Brush-level stabilization lives inside each brush's settings, so you can have a loose sketching pencil and a tightly controlled inker in the same document.
Within a brush, there are three modes, plus a sub-setting:
- StreamLine tightens a line and removes small wobbles while keeping the curves and turns you intended. It suits inking, calligraphy, and lettering.
- Stabilization draws the stroke toward the calculated average between its start and end points. The effect is more dramatic: corners soften and lines straighten.
- Motion Filtering also pulls the line toward the center of the stroke, but it spots unexpected changes in your motion, large or small, and ignores them when calculating that average.
- Expression is a sub-setting of Motion Filtering that lets more of your natural character through, so a curve or corner can be emphasized instead of flattened.
All of these respond to speed. The effect increases the faster you move, so quick, shaky motion gets corrected while slow, deliberate movement is mostly preserved. That is why heavily stabilized brushes still feel controllable when you slow down for detail.
How to set global stabilization
Use this when you need consistent smoothing across everything, for example when your hand is tired, you're working on a small screen, or you're tracing long contours.
- Tap the Actions icon (the wrench).
- Go to Prefs > Pressure & Smoothing.
- Adjust the Stabilization slider, which runs from 0 to 100%.
Begin around 10-15% and increase gradually. Draw a few long curves and a few short tight ones after each change, because a value that feels fine on a long sweep can feel mushy on small details.
A common complaint with this setting is that the pen suddenly feels laggy or unresponsive. Very often, a global stabilization value was left high from a previous task. If your lines trail behind your pencil or corners refuse to stay sharp, check this slider first.
How to set stabilization on a single brush
Per-brush control is usually the better approach, because different tools need different amounts of correction.
- Open the Brush Library by tapping the brush icon.
- Tap a brush to select it, then tap it again to open Brush Studio.
- Choose the Stabilization tab from the left-hand list.
- Adjust the values:
- StreamLine > Amount for smoothing out wobbles and shakes.
- StreamLine > Pressure for how gradually pressure is applied along the stroke. Higher values give a longer, smoother pressure ramp, and lower values make pressure respond more quickly.
- Stabilization > Amount for averaging and straightening.
- Motion Filtering and Expression for ignoring spikes while keeping character.
Before editing a stock brush, swipe left on it in the library and choose Duplicate. That way your changes don't overwrite the original. If you do change too much, open the brush in Brush Studio, go to About this Brush, and tap Reset Brush to restore its defaults, including stabilization.
Picking the right mode for the job
Rather than maxing out one slider, think about what kind of error you are trying to remove.
The following values are only starting points. Every brush, screen size, and drawing speed behaves a little differently, so expect to adjust them:
- Clean inking or lettering: moderate StreamLine, low Stabilization.
- Long flowing contours, such as character silhouettes or motion paths: higher Stabilization, with some Expression to avoid a rigid result.
- Loose roughs and gesture drawings: little to none. Smoothness works against energy here.
Stabilization is also the wrong tool when you want texture (fur, frayed edges, rough washes), sharp corners (mechanical shapes, angular seams), or precise technical detail. In those cases, turn it down or off at both the global and brush levels.
Troubleshooting a pen that still feels wrong
The line lags behind the pencil. Lower the global Stabilization slider, then check the brush's own StreamLine and Stabilization amounts. Both global and brush-level stabilization can contribute to the delay.
Corners are rounded off when you don't want them to be. Stabilization averages toward the middle of a stroke, which softens corners. Reduce it, or switch to StreamLine, which keeps turns more intact.
Lines are smooth but boring. You have probably over-corrected. Pull back Stabilization and use Expression to restore some character.
A brush behaves strangely after tweaking it. Reset it from About this Brush, or restore the duplicate you made earlier, then change one value at a time.
Pressure feels off, not just the line shape. Stabilization isn't the only factor. Check the brush's own StreamLine Pressure setting as well.
Technique matters as much as settings
Software smoothing works best when your physical setup is already steady.
- Zoom in for detail and out for sweep. Short, controlled strokes at high zoom are naturally steadier. Long arcs are easier to draw at a smaller zoom, where the whole gesture fits under your hand.
- Rotate the canvas so the stroke follows your wrist's natural arc rather than fighting it.
- Draw with confident speed. Because stabilization effects scale with how fast you move, a quick, committed stroke is often cleaner than a slow, nervous one.
- Anchor your hand. Rest the side of your palm on the screen and move from the elbow or shoulder for long lines.
Why motion and VFX artists care about a steady line
If you work in After Effects, Premiere Pro, Cinema 4D, Blender, or Nuke, Procreate often shows up at the start of the pipeline: storyboards, styleframes, character and prop concepts, hand-drawn mattes, or frame-by-frame passes. A stable, deliberate line matters there because it gets scaled, animated, traced, or composited later. Wobble that looks charming at tablet size can turn into visible jitter once a shape is vectorized, rigged, or blown up to 4K.
A few practical habits help:
- Create dedicated brushes for line work with fixed stabilization, and keep a separate unstabilized set for roughs, so you aren't constantly changing global settings.
- Draw at the final resolution or higher whenever possible, so smoothing doesn't have to hide pixelation.
- Keep linework on its own layer, separate from color and shading, so it can be exported and handled independently in After Effects or Nuke.
Quick reference
- All brushes: Actions (wrench) > Prefs > Pressure & Smoothing > Stabilization (0-100%).
- One brush: Brush Library > tap the brush > Brush Studio > Stabilization tab.
- Wobble: StreamLine Amount.
- Straightening: Stabilization Amount.
- Sudden bumps: Motion Filtering, with Expression to keep character.
- Lag: check global Stabilization first, then the brush's own values.
- Undo experiments: duplicate brushes before editing, and use Reset Brush when needed.
Treat stabilization as a per-brush decision rather than a single global fix. Set a light global baseline, give each tool the kind of smoothing its job needs, and your lines will stay controlled without losing the hand-drawn quality that makes them worth using.