How to Stabilize Brush in Procreate
StyleFrame Team7 min read
To stabilize a brush in Procreate, open Brush Studio (tap the brush in the Brush Library, then tap it again), go to the Stabilization tab, and raise Stabilization Amount and StreamLine Amount. For smoothing that applies to every brush, go to Actions (wrench) > Prefs > Pressure & Smoothing and raise the Stabilization slider. Start low, around 10-15%, and increase until lines feel controlled without noticeable lag.
Two Places to Stabilize: Global vs. Per-Brush
Procreate gives you two layers of smoothing, and many "my brush feels weird" problems come from forgetting that both exist.
- Global stabilization is an app-wide preference. It overrides individual brush behavior, so every stroke is smoothed, even with a brush that was designed to be raw.
- Brush-level stabilization lives in Brush Studio and is saved with that brush. It's the better default for most work because a pencil, an inker, and a texture brush each want different amounts of smoothing.
If a brush suddenly feels laggy or doesn't respond sharply to your Apple Pencil, check the global slider first. A high leftover value is a common cause.
How to Set Global Stabilization
- Tap the Actions (wrench) icon.
- Open Prefs, then Pressure & Smoothing.
- Drag the Stabilization slider (0-100%).
Treat it like a task-based setting. Raise it for a session of clean line art, then drop it back when you switch to sketching or painting. A global value is convenient when you want consistent smoothing across a whole set of tools, but it's easy to forget it's on.
How to Stabilize an Individual Brush
- Open the Brush Library and tap the brush you want.
- Tap the same brush again to open Brush Studio.
- Select the Stabilization tab in the left-hand list.
- Adjust the sliders (details below).
Before editing a brush you like, duplicate it by swiping left on it in the library and choosing Duplicate. That gives you a "stabilized" version and an untouched original. If you've changed too many settings and want to start over, open Brush Studio, go to the About this Brush tab, and tap Reset Brush. This restores all of the brush's settings, stabilization included.
Duplicating also solves a complaint that comes up often among Procreate users: having to change a brush's settings temporarily and then remember to revert them. Keep two versions of your go-to inker (loose and locked-down) and switch between them instead of editing one.
Understanding the Stabilization Tab
The tab has two main systems, and they behave differently.
Stabilization Amount
Stabilization works by taking a moving average of your stroke and drawing that result on the canvas. The more you raise it, the more the app averages out small wobbles, so the stroke becomes more deliberate and straighter than your hand actually drew it. This is the setting to reach for when you're drawing long, controlled curves or clean outlines.
The tradeoff is latency. Heavy values can make the line feel laggy, as if you're dragging the stroke behind you.
StreamLine
StreamLine smooths out wobbles and shakes in your line, and it's especially valuable for inking and calligraphy. It has two sliders:
- Amount: Higher values give a smoother, more even stroke. Lower or off gives more natural, less polished linework.
- Pressure: Higher values spread pressure changes over a longer distance, so a stroke's weight builds more gradually. Lower values make pressure respond more quickly as you press.
Which One Should You Use?
Streamline tends to feel like the line is being pulled along by a string. That's great for lettering and flowing curves, but some illustrators find it less satisfying for precise line art, especially when drawing slowly. Some users on Procreate's community forum have asked for a stabilizer closer to the ones in other apps, and some of them describe small ripples in lines that they know they drew straight.
In practice:
- Use StreamLine for flowing, confident strokes: lettering, inking, calligraphic contours.
- Use Stabilization for averaging out jitter on slower, controlled strokes.
- Combine them in moderate amounts rather than maxing one out. Most brushes feel best with each set to a middle value that you've tested on real strokes.
Other Settings That Make a Stabilized Brush Still Look Wobbly
Sometimes the wobble isn't a smoothing problem at all. Check these in Brush Studio before pushing stabilization higher:
- Spacing: Wide spacing makes the brush read as a series of stamps. Reducing spacing toward zero merges the shapes into one fluid stroke, which makes any line look smoother.
- Jitter (Lateral and Linear): These deliberately push stamps off the path. If you want a clean line, keep them at zero. Jitter values can also be tied to Apple Pencil pressure and tilt, so a brush may only misbehave when you press a certain way.
- Spacing Jitter: Even with base spacing at 0%, high jitter can still change spacing because there's a minimum spacing value.
- Pressure response: Apple Pencil is sensitive to small pressure changes, which can produce uneven line weight even when the path is smooth. Raising StreamLine Pressure makes weight transitions gentler.
- Fall Off: If strokes fade as they travel, the line can look uneven. Turn it off for consistent opacity.
When You Should Turn Stabilization Down
Smooth isn't always better. Lower or disable stabilization when you need:
- Energy and speed in gesture drawing or rough sketches
- Intentional texture, like fur, frayed edges, or dry-media effects
- Sharp corners and angular shapes, which heavy smoothing rounds off
- Precise placement, where lag would make you overshoot
Troubleshooting Checklist
If your lines still don't feel right, work through this in order:
- Check global stabilization in Prefs > Pressure & Smoothing and set it to 0 as a baseline.
- Open the brush in Brush Studio and review the Stabilization tab.
- Check Stroke Path settings for jitter and spacing.
- Reset the brush from About this Brush if you've lost track of changes.
- Compare against a fresh default brush to see whether the issue is the brush or your setup.
Using Stabilized Procreate Linework in a Motion Pipeline
For motion designers and animators, Procreate is often a frame-by-frame sketchbook, a way to draw style frames, or a source of hand-drawn elements (outlines, lettering, texture passes) that end up in After Effects. A few habits help downstream:
- Pick a smoothing profile per asset type. Loose, energetic settings for boiling-line animation; heavier stabilization for logo-adjacent lettering or clean outlines that must hold up under scaling.
- Keep it consistent across frames. If stabilization drifts between sessions (a forgotten global value, an edited brush), line quality will visibly shift from frame to frame. Duplicating locked-in brushes prevents this.
- Work large. More canvas resolution means more room to scale, rotate, and composite in After Effects without line quality breaking down.
- Export in a form your comp can use. PNG sequences or layered files let you rebuild the piece in After Effects, Nuke, or another compositing tool and keep control over timing and effects.
Quick Reference
Final Advice
Stabilization is a feel setting, so tune it by drawing, not by numbers. Duplicate your key brushes, label them by purpose, and keep global stabilization low unless you've deliberately raised it for a task. With a few reliable brush profiles, your linework stays consistent across a project, whether it ends up as a still, a hand-drawn animation, or source material for the rest of your pipeline.