How to Smooth Procreate Putty
StyleFrame Team6 min read
To smooth ProCreate Putty, work the surface while it is still uncured, using a soft, flat brush barely dampened with water or 90%+ isopropyl alcohol, and use a sculpting tool or handle rather than your fingers. Once it has cured, remove marks with fine-grit sandpaper, then buff with a grey Scotch-Brite pad. Light pressure, a clean brush, and a small amount of lubricant matter more than any single product.
This guide covers the epoxy sculpting putty used for miniatures, busts, and maquettes. If you were looking for smoother strokes in the Procreate iPad app, skip to the short note near the end.
Know What You're Smoothing
ProCreate Putty is a two-part epoxy putty, mixed from components A and B, that hardens gradually. It has reportedly been discontinued, so many sculptors are now moving to other putties and carrying over the techniques they learned on it. Most of what follows applies to any similar epoxy putty.
Its character explains why it smooths well:
- It is less sticky than Green Stuff (Kneadatite). You need less lubricant on your tools, though it adheres to the model a little less eagerly. It sticks to itself readily.
- It has little "shape memory." Green Stuff tends to creep back toward its previous form when you press it. ProCreate holds a push, which makes subtle surface blending easier.
- It stays workable after curing. Sculptors report carving and sanding it once hard, and that it stays smoother when filed or cut than Green Stuff.
- It cures grey. Sculpting in the color of a finished, primed model makes surface flaws easier to read.
If you are switching putties, expect differences. Green Stuff is stickier and can be harder to smooth at first, though it firms up as it cures. Magic Sculp is known for a creamy texture and long working time. Test any substitute on scrap before committing to a real piece.
Start With a Cleaner Mix
Smoothing begins at the mixing stage. Lumps, dried flecks, and trapped air all show up later as marks.
- Measure accurately. Separate components give you more control over the ratio than a pre-joined strip. Follow the manufacturer's guide for your task, since ratio changes stickiness and cure time.
- Trim contaminated edges. Putty stored for months can dry out along the outside. Slice off any dried edge and the hard lump where two colors join. Otherwise you get hard flecks in your sculpt.
- Mix until the color is uniform. Streaks mean unmixed resin or hardener, and those areas cure differently and sand differently.
- Don't wait too long to apply. Work time varies by putty. One experienced sculptor reports Green Stuff stays tacky only 10 to 15 minutes before it becomes hard to place. Get the putty onto the model promptly and refine afterward.
Smooth Uncured Putty
This is where most of the work should happen. Smoothing wet putty removes the need for heavy sanding later.
Use a Handle, Not Your Fingers
Fingerprints are a common cause of texture that "won't sand out." Mount small pieces on a dowel with a pin in the end, or a larger dowel or block of wood for bigger work, so you can rotate the piece without touching the putty.
Brush Smoothing With Alcohol or Water
A widely used method is a small, soft, flat brush lightly dampened with isopropyl alcohol (90% or higher). Alcohol evaporates faster than water, so it softens the surface just enough to level it without leaving it slushy.
- Use very little. An overloaded brush turns the surface mushy and lifts detail.
- Stroke in one direction with light pressure, as if smoothing clay on a pottery wheel, only without the rotation.
- Rinse the brush thoroughly afterward. Thinned putty left in the bristles will set it as hard as rock.
- Use alcohol in a ventilated space and keep it away from flames.
Water works too. It is free, available at the tap, and at least one experienced sculptor prefers it. Other lubricants people report using include lip balm, and a mix of alcohol and oil from a hair tonic. Results vary, so test on scrap and clean the surface before painting.
Use Silicone Shapers
Silicone clay shapers, which are brush-like tools with rubbery tips in various shapes, are another option. Because ProCreate is less sticky than Green Stuff, you often need only a trace of lubricant on them.
Work in Stages
Don't try to finish a whole piece in one pass. Build the form, let the putty firm up, then refine. As it stiffens, tools smooth it rather than drag it, which is the stage where fine blending works best. One sculptor reports that ProCreate dries faster than Green Stuff, enough to sculpt a small model in a day under a table lamp, so watch the clock and don't overwork it.
Smooth Cured Putty
If the putty has hardened and still has marks, switch from lubricants to abrasives.
- Start with fine-grit sandpaper. Sand lightly and evenly. If sanding isn't removing fingerprints, the marks may be deeper than the grit can reach, so step down in coarseness briefly, then move back up.
- Use files for edges and flats. Cured ProCreate can be carved and filed, so you can correct form as well as texture.
- Finish with grey Scotch-Brite. It clears fine scratches and sanding marks. One sculptor switched to it from steel wool, which left rusty particles behind.
- Fill and repeat if needed. Thin a little fresh putty over low spots, smooth it uncured, cure it, then lightly sand again.
Wear a dust mask when sanding cured epoxy and work in a ventilated area.
Troubleshooting Common Problems
Surface keeps showing marks after sanding. The marks are probably fingerprints or tool drag baked into the surface. Smooth the uncured putty first and use a handle on the next piece.
Putty drags and lifts when you touch it. It is either too sticky for the tool or you are working it too early. Lightly lubricate the tool, or wait a few minutes for it to firm up.
Surface goes slushy. Too much alcohol or water. Stop, let it evaporate, and use less.
Rough, grainy texture. This may be a different putty rather than a technique problem. Milliput, for instance, is designed to mimic ceramic and has a grainy texture that some sculptors find awkward for miniature work.
Tiny hard flecks. Old, dried putty got into the mix. Trim the edges next time.
A Note on the Procreate App
If you meant the iPad drawing app, smoothing there is a software setting, not a technique. Open the Actions menu, go to Prefs, then Pressure & Smoothing, and raise the global Stabilization slider (starting around 10 to 15% is a sensible test). For finer control, open a brush in Brush Studio and adjust its Stabilization and StreamLine amounts. Duplicate a brush before editing it, and turn stabilization down when you want energetic, textured lines, since too much can make your pencil feel laggy.
Quick Reference
- Use a handle to keep fingers off the putty.
- Mix thoroughly and trim dried edges first.
- Smooth uncured putty with a soft flat brush and minimal alcohol or water.
- Clean brushes immediately.
- For cured putty, sand fine, then buff with grey Scotch-Brite.
- Test any new putty or lubricant on scrap first.
Smooth sculpts come from working the putty at the right moment with the lightest touch. Practice on scrap with your chosen lubricant, learn how long your putty stays workable, and you'll spend far less time sanding.