How to Set Opacity in Procreate
StyleFrame Team6 min read
To set opacity in Procreate, open the Layers panel, tap the "N" beside a layer, and drag the Opacity slider. You can also tap a layer with two fingers and slide left or right to lower or raise opacity. For brushes, drag the lower slider in the sidebar. For a selected area of paint, use the two-finger layer gesture and then slide on the canvas.
Procreate has several opacity controls, and they differ in scope and in whether you can revisit them later. Picking the right one saves you cleanup, especially if the artwork is headed into After Effects, Premiere Pro, or a compositing pipeline.
What Opacity Means in Procreate
Opacity is how visible a pixel is. At 100% it is fully visible, and at 50% it is half see-through. Procreate lets you apply that value at three levels:
- Brush: controls how strongly each stroke lays down paint.
- Layer: controls the visibility of everything on a layer, as one value.
- Selection: controls the visibility of only the selected pixels on a layer.
The third behaves differently from what you might expect, and it has consequences covered below.
How to Change Brush Opacity
Brush opacity sets how transparent your next stroke will be, and it doesn't touch anything you've already painted.
- Select the brush you want to use.
- Find the two sliders on the left sidebar. The lower slider controls opacity.
- Drag it up to increase opacity or down to decrease it.
- Paint a test stroke on a scrap layer to confirm the result.
Brush opacity is the right choice for building up soft shading, glazing color over color, or laying in translucent smoke and haze by hand. Strokes laid down at low opacity build toward a denser look as they overlap, much like layering semi-transparent shapes in a motion graphics comp.
When the Brush Looks Too Faint
If opacity is at maximum and strokes still look washed out, Apple Pencil pressure is the likely cause. Many brushes tie opacity to pressure, so a light touch yields a lighter mark regardless of the slider. Press harder, or check your Apple Pencil pressure settings. Also confirm that you're painting on the layer you think you are, since a layer already set to low opacity will dim everything on it.
How to Change Layer Opacity
Layer opacity is the setting you'll use most often. There are two routes to it, and both start in the Layers panel (the two overlapping squares at the top right).
Method 1: The "N" Menu
- Open the Layers panel.
- Tap the small letter to the right of the layer name. It reads "N" for Normal by default, and it changes if you've applied another blend mode.
- A panel opens with the blend mode list and an Opacity slider directly beneath it.
- Drag the slider to the percentage you want. The value is displayed as you drag.
This route is slower, but it gives you the blend mode and opacity in one place. That's useful when you're building shadow, glow, or texture layers that need both.
Method 2: Two-Finger Tap
- Open the Layers panel.
- Tap the target layer with two fingers at the same time. An opacity bar appears at the top of the screen.
- Slide left to lower opacity and right to raise it, using a finger or Apple Pencil.
This is the quicker method once it's muscle memory. It only affects one layer at a time, so if you need several layers at the same value, set each one individually.
Why Layer Opacity Is Non-Destructive
Layer opacity is a property of the layer, not a change to its pixels. You can return to the slider and change it as often as you like. That makes it the safest option when you're still deciding how a layer should sit in the composition.
How to Change the Opacity of a Selection
Sometimes you only want part of a layer to be more transparent, like a single shape on a busy layer. Procreate handles this with a selection plus a gesture.
- Open the Selection tool and choose your preferred method.
- Make your selection.
- Open the Layers panel.
- Tap the layer containing the paint with two fingers at once.
- Slide a finger left on the canvas to reduce opacity, or right to increase it.
- Exit the mode to apply the change.
The key detail is that this is destructive. When you leave the mode, Procreate commits the change to the pixels. You can undo right away, but you can't return later and adjust the percentage as you can with a layer slider. If you may want to adjust it again, duplicate the layer first, or cut the selection to its own layer and use layer opacity there instead.
Using Adjustments > Opacity
Procreate also has an Opacity option under the Adjustments menu. In the version of the handbook that documents it, you tap Adjustments, then Opacity, and slide left or right on the screen to change the active layer's transparency. A bar at the top shows the current value, starting at 100%.
The bottom controls let you cancel everything, undo the last step, redo it, or reset while staying in the tool. To commit, tap the Adjustments icon again or switch to another tool. Menu layouts shift between Procreate versions, so if you don't see it where described, check your version's handbook. In practice, this is the same gesture-based approach as the two-finger method, with explicit undo and reset controls.
Which Opacity Method Should You Use?
If you're unsure, default to layer opacity. Splitting elements across layers costs you nothing and keeps your options open.
Common Opacity Problems and Fixes
- The slider seems to do nothing. Check that the right layer is active. Opacity changes apply to the selected layer only.
- A stroke won't paint opaque. Look at both the brush opacity slider and the layer's own opacity. Both affect the result, so a low brush opacity on a low-opacity layer gives a much fainter result.
- A clipping mask behaves unexpectedly. A layer clipped to the one below only paints where the base layer has pixels.
Taking Procreate Opacity Into a Motion Pipeline
Procreate is common for hand-drawn frames, textures, matte paintings, and style references. A few habits make those assets friendlier downstream:
- Keep elements on separate layers. Layer-level opacity stays adjustable, whereas selection-opacity changes are baked in.
- Treat Procreate opacity as a starting point. If you plan to animate a fade, export the layer at full opacity and animate the property in your compositor, where you get keyframes and easing.
- Check blend modes after import. Opacity and blend modes travel together, and not every mode necessarily matches one-to-one across apps. Compare against your Procreate reference before locking a look.
Quick Reference
- Brush: lower sidebar slider.
- Layer: "N" menu slider, or two-finger tap on the layer then slide.
- Selection: make a selection, two-finger tap the layer, slide on the canvas (destructive).
- Adjustments: Adjustments > Opacity, slide, then commit or cancel.
Pick the least destructive method that does the job, keep elements separate, and leave animated fades for your compositor.