How to Select Things in Procreate
StyleFrame Team7 min read
To select things in Procreate, tap the Selection tool (the S icon in the top-left toolbar), pick one of four modes (Automatic, Freehand, Rectangle, or Ellipse), then mark the area you want. Use Add, Remove, Invert, and Feather to refine the selection, and Copy & Paste to lift the contents onto their own layer. Selections only affect the active layer, so check which layer is active before you start.
The rest of this guide covers each mode, the refinement controls, a few gestures that save time, and how selections fit into a motion pipeline when your final destination is After Effects, Nuke, or another compositing tool.
Where the Selection Tool Lives
The Selection tool is the S-shaped icon in the top toolbar, next to the Transform (arrow) tool. Tapping it opens a bar with the four mode buttons and the refinement options. Tap the S icon again to deselect and exit.
While a selection is being drawn, you'll see a moving outline. Once it is finalized, the area outside the selection is covered with a diagonal-striped mask, and the selected area stays clear. If the stripes are distracting or too faint, the mask visibility can be adjusted in the canvas settings.
The Four Selection Modes
Automatic
Automatic selects by color. Tap an area and Procreate selects that region plus any bordering pixels that are similar. Before lifting your finger or Pencil, drag left or right to change the selection threshold:
- Lower threshold: Stays close to the exact color you tapped. Good for flat fills and clean line art.
- Higher threshold: Pulls in a wider range of similar values. Useful for gradients, textured shading, or anti-aliased edges.
Automatic works on the contents of the active layer, which is the most common source of confusion. If you tap and nothing sensible happens, you are probably on a different layer than the artwork you're trying to pick.
This mode is the fastest way to isolate flat-color shapes, such as a character's jacket or a background block, without tracing anything. It struggles with painterly or noisy textures, where color variation makes the selection ragged. In those cases, switch to Freehand.
Freehand
Freehand is the precision option. Trace around the area with your finger or Apple Pencil, and the selection closes automatically when you lift. You can also tap from point to point to make straight-edged polygonal selections, which is handy for hard-surface shapes like buildings, UI panels, and props.
Because it behaves like drawing, Freehand suits organic shapes: hair, hands, clothing folds, anything that doesn't follow a geometric edge. Zoom in before tracing around detailed areas. A selection made while zoomed in is far cleaner than one made at fit-to-screen.
Rectangle
Drag diagonally to create a rectangular selection. Holding a second finger on the screen while you drag snaps it to a perfect square. Use it for cropping out a region, clearing a background panel, or isolating a frame-shaped element.
Ellipse
Ellipse works like Rectangle but produces an oval. A second finger held down snaps it to a perfect circle. It's good for eyes, wheels, UI dots, and soft vignette areas.
Refining a Selection
Rarely does the first attempt capture exactly what you want. These controls let you adjust without starting over.
Add and Remove
Add is the default behavior: each new selection is combined with the existing one. Remove subtracts from it. You can mix modes freely. For example, grab a large area with Rectangle, then switch to Freehand in Remove mode to carve away the corners you didn't want.
Invert
Invert flips the selection so everything that was unselected becomes selected. This is a quick way to select a complex subject: select the simple background with Automatic, then invert.
Feather
Feather softens the selection edge. This matters when you're adjusting color, blurring, or painting within a selection and don't want a hard boundary. Use a small amount to blend a correction invisibly, and avoid it on selections you'll lift to new layers for compositing, where you typically want crisp edges.
Undo and Redo During Selection
A two-finger tap undoes the last step of a selection, and a three-finger tap redoes it. This lets you back out of a bad point while tracing without losing the whole selection.
What You Can Do With a Selection
Once an area is selected, edits apply only inside it:
- Paint, erase, or fill without touching the rest of the layer.
- Apply Adjustments such as Hue and Saturation to just that region.
- Move and transform by tapping the Transform tool (the arrow). You can scale, rotate, flip, or distort the selected content.
- Copy & Paste to put the selected content on a new layer, leaving the original untouched.
- Cut & Paste with a three-finger swipe, which opens a menu with Cut, Copy, and Paste options. Choosing "Cut & Paste" removes the content from the original layer and places it on its own layer.
- Clear the selected pixels from the layer.
Separating Elements Into Layers
This is the most useful trick for anyone who plans to animate or composite the artwork later. If you painted several elements on a single layer (a character, a prop, and a shadow, say), use Automatic or Freehand to select one, then Cut & Paste it onto a new layer. Repeat for each element. You end up with a layered file you can rearrange, hide, and export.
Selecting Whole Layers and Multiple Layers
Selecting content isn't the same as selecting layers, and both come up often.
- Group layers: Grouping several layers lets you transform them as a single unit. This is useful for rigs where a character's limbs need to be transformed together.
If your Selection tool seems to be doing nothing, check the active layer first.
Common Problems and Fixes
Automatic selects too much or too little. Adjust the threshold. If the artwork has textured shading, try a higher value, or switch to Freehand for the problem region.
Edges look jagged after moving a selection. Anti-aliased edges can leave a fringe. Try a very small feather before transforming, or select slightly outside the shape and clean up afterward.
Content disappears when you copy. Remember that selections only act on the active layer. If your artwork is spread across multiple layers, merge them or select each layer separately.
The selection won't go away. Tap the Selection tool again to deselect. Leaving a selection active while painting is a common reason strokes seem to vanish outside an area.
Using Procreate Selections in a Motion Pipeline
For motion designers, animators, and compositors, the selection tool is less about illustration and more about preparing assets. A few practical habits help the handoff go smoothly:
- Separate elements before export. Use Cut & Paste to split a flat painting into logical layers: foreground, midground, character parts, effects. Name them clearly.
- Keep edges clean. Hard, accurate selections make better cutouts. Avoid heavy feathering on anything that will be composited on a different background.
- Export layered files. Export a layered file your compositing tool can open. That lets you animate parallax, rigs, or camera moves in the compositor.
Where Styleframe Fits
Procreate is a strong place to build frames, concept art, and layered assets. Once you have stills, a tool like can extend them into motion. The point is that your selection work in Procreate and your compositing work downstream stay intact.
Quick Reference
Final Tips
Get in the habit of confirming the active layer before every selection. Zoom in for detail work. Use Automatic for flat shapes, Freehand for anything organic, and Add/Remove to fix mistakes rather than redoing the whole selection. With those habits, selecting in Procreate becomes fast enough to stay out of your way, whether you're finishing an illustration or prepping layers for a motion project.