How to Select Same Color on Procreate
StyleFrame Team7 min read
In Procreate, the Selection tool's Automatic mode selects a color: tap the color on the active layer, then drag your finger left or right to set the threshold. To grab several separate patches of the same color, switch on Add and tap each patch. If you only need to reuse a color you've already painted with, hold your finger on the canvas to eyedrop it, or pick it from your Color History. Procreate has no single-tap "select every pixel of this color across the canvas" command, so the workflow below is the practical way around that.
Two Things "Select Same Color" Can Mean
People searching this phrase usually want one of two things, and Procreate handles them with different tools:
- Pick the same color again so a new brushstroke matches an existing one.
- Select every area of a color so you can recolor, erase, copy, or mask it.
The first is the Color Picker and Color Panel. The second is Automatic Selection, with Recolor and Alpha Lock as alternatives. Start with whichever matches your task.
Reuse an Exact Color You Already Painted
Use the eyedropper
Touch and hold on the canvas where the color lives. Procreate sets your active color to whatever sits under your finger. Release to confirm.
Sample from a flat, non-textured area when you can. Brushes with grain or opacity variation produce slightly different pixels, so you may pick up a shade that is close but not identical to the one you intended.
Use Color History
The Color Panel keeps your last ten colors on the Disc, Classic, Harmony, and Value tabs. Each new color pushes the oldest one out, and a new artwork starts with an empty history. If you've just sampled something and wandered off to a different shade, the earlier one is probably still in that row.
When you drag the small reticle on the color disc, the split circle shows the color you're hovering over beside the most recent color in your history. That makes it easy to compare a new choice against the shade you were just using.
Lock a color into a palette
If a color needs to survive the whole project, save it as a swatch in the active palette, which appears at the bottom of the Color Panel. History is temporary. Palettes are not.
Match by value, not by eye
On the Value tab you get numeric sliders and a hex field, which are ideal for precise color matching. If the color you need exists in a style guide, brand board, or After Effects comp, type or paste the hex code. This is a more reliable way to get a match across apps than eyeballing a swatch on an iPad display.
Select All of One Color With Automatic Selection
This is the core method for selecting areas of one color.
- Pick the right layer. Automatic Selection reads the active layer, not the visible composite. Many failed selections come from working on the wrong layer.
- Open the Selection tool.
- Choose Automatic.
- Tap the color you want. Procreate selects the matching region and shows the marching-ants outline.
- Drag your finger left or right without lifting after the tap. This sets the selection threshold: higher values pull in more similar shades, lower values stay strict.
- Lift your finger to commit the selection.
From there you can fill, cut, copy, feather, invert, or save the selection for later.
Selecting separated patches of the same color
Automatic Selection works from the point you tap, so patches that aren't connected usually need separate taps. The approach:
- Make your first selection as above.
- Toggle Add in the selection controls.
- Tap each additional patch of the color, adjusting threshold if edges are missing.
- Check the outline carefully before committing to any destructive edit.
It is manual, and on art with dozens of small islands it gets tedious. Users have asked Procreate for a one-click version that selects an exact color across the whole canvas, similar to what Clip Studio Paint offers. In that discussion, a reply said it isn't directly planned, though future improvements might lend themselves to the idea. Treat it as a workaround-required feature for now.
Erasing one color to transparency
A common reason for needing this is a flattened JPEG with a solid background you want gone. A reliable sequence is:
- Select the background color with Automatic Selection and adjust the threshold.
- Add any disconnected background areas.
- Use the three-finger swipe down to open the Copy/Paste menu and choose Cut.
Note that the Clear button in the selection toolbar only removes the selection outline; it doesn't erase pixels. The clear-layer gesture clears the layer content within the selection, and Cut does the same job through the menu.
Fix Edges and Fringes
Anti-aliased art is where selections go wrong. The pixels along an edge are blends between two colors, so a strict threshold leaves a halo of half-colored pixels.
- Raise the threshold a little until the halo is covered, then check on a contrasting background.
- Feather the selection slightly if you'll be filling or recoloring, which softens the transition.
- Use Invert when the shape you want is easier to select by its opposite, such as a flat background around a complex figure.
- Zoom in before committing. A selection that looks clean at fit-to-screen often hides gaps when you zoom in.
If the art is hard-edged pixel work, keep the threshold low so you don't bleed into neighboring colors.
Recolor Instead of Select
When your goal is to change a color rather than isolate it, Procreate's Recolor tool can skip the selection step. It's available through the Quick Menu once you assign it to one of the slots (via the Actions menu > Prefs > Gesture controls).
How it behaves:
- Make sure you're on the correct layer first.
- When you activate it, a small crosshair appears. Drag it onto the area you want to change.
- Recolor uses your current color, and it updates in real time as you change the color in the panel.
- If the wrong region changes, such as the whole background, the crosshair is sitting on the wrong spot. Move it onto the object.
- If it doesn't cover everything, adjust the flood threshold at the bottom of the screen.
Recolor is simplest on a flat layer of a single color. With heavy texture on the layer, the result shifts depending on where the crosshair is, so experiment with placement.
Alpha Lock for Whole-Layer Color Changes
If each color lives on its own layer, you don't need color selection at all. Swipe two fingers right on the layer to enable Alpha Lock, then fill or paint. Only existing pixels are affected. This is cleaner than any threshold-based selection and is the better habit if the file is headed to animation, because separated flat colors are far easier to manage downstream.
Common Problems
- Nothing selects as expected: you're probably on a different layer than the one containing the color.
- Selection spills into other areas: the threshold is too high, or the color touches a similar shade.
- Edges look chewed up: raise the threshold slightly or add feathering.
- Color looks the same but selects differently: textured brushes produce subtle variation, so you may be dealing with many near-identical colors rather than one.
- Selecting from the composite: Automatic Selection doesn't read across layers, so merge or duplicate-and-merge a working copy when you need that.
Where This Fits in a Motion Pipeline
Many motion designers and animators sketch, paint backgrounds, or build character art in Procreate and then finish in After Effects. A few habits make that handoff smoother:
- Separate flat colors onto their own layers and name them. That gives you clean mattes without needing to rebuild selections.
- Export layered files or individual PNGs with transparency, then use After Effects' color and matte tools for last-minute adjustments.
- Keep hex values of key colors in a note or palette so Procreate and your comp stay consistent.
Once your art is in order, is an AI video and motion tool that works from reference material. Your Procreate frames and palettes can serve as that reference, which keeps the artistic decisions yours.
Quick Reference
Procreate rewards a little planning here. Keep colors on separate layers where you can, save important swatches to a palette, and treat Automatic Selection plus Add as your standard route when you need to grab one color in many places.