How to Select Only Black in Procreate
StyleFrame Team7 min read
Procreate has no single "select by color" command, but you can isolate black in a few reliable ways. Put the black on its own layer and tap the layer, then choose Select. Or use Selection > Automatic, tap a black area, drag to set the threshold, and switch to Add mode to pick up the other black regions. Once the black is selected, cut it to a new layer, recolor it with Alpha Lock, or export it as a transparent PNG for After Effects or Nuke.
What "Select Only Black" Means in Procreate
Procreate's selection tools are built around shapes and regions, not color ranges. Automatic selection grows from the pixel you tap and stops where the color changes, so it selects contiguous areas of similar color, not every black pixel on the canvas. Users have asked for an erase-by-color or global color-select function, but as of the versions we've worked with, the workaround is to combine layers, selections, and adjustments. Check your current version's handbook in case that has changed.
What you need depends on the job:
- Black line art on a transparent layer: you want the linework as a clean matte or recolorable layer.
- Black line art on a white background (a scan or JPEG): you need to separate the black from the paper.
- Black shapes in a flat illustration: you want to select, move, or replace specific black regions.
Each has a different best method below.
Method 1: Select the Layer's Pixels (Best for Line Art on Its Own Layer)
If your black elements already sit alone on a transparent layer, this is the fastest and cleanest approach.
- Open the Layers panel and tap the layer containing the black elements.
- Tap Select in the layer menu. Procreate selects the layer's non-transparent pixels.
- Use the selection however you need: fill, copy, cut to a new layer, or invert it to select everything except the black.
This is far more precise than drawing a freehand lasso. It also avoids the problem of thresholds, because the selection is based on layer content rather than color similarity.
If you only need to recolor the black, skip the selection. Tap the layer and choose Alpha Lock, then paint or fill over it. Only the existing black pixels change.
Method 2: Automatic Selection with Add Mode
When the black is mixed with other colors on a single layer, Automatic selection is the standard route.
- Select the layer that holds the artwork.
- Tap the Selection tool (the S-shaped icon) and choose Automatic.
- Tap a black area. Keep your finger down and drag left or right to adjust the threshold. A lower threshold selects only near-pure black. A higher one pulls in dark grays and anti-aliased edges.
- Release, then tap Add at the bottom of the screen and tap the other black regions one by one.
- Use Remove to subtract any areas that crept in.
A few practical notes:
- Anti-aliased edges are the usual trouble spot. A low threshold leaves a thin gray fringe unselected. A high threshold swallows adjacent darks. Zoom in and test on an edge before committing.
- Feather (in the selection menu) softens the edge of the selection if you plan to cut or fill it.
- For artwork with many separate black islands, such as halftones, hatching, or small text, Add mode gets tedious. Use Method 3 instead.
Method 3: Push the Image to Pure Black First
If your artwork is a scan, a photo, or a JPEG with muddy blacks, clean the tones before selecting.
- Duplicate the layer so you have a safe original.
- Open Adjustments > Curves. Pull the black point and white point toward each other so that near-black tones become solid black and everything lighter goes toward white.
- Commit the adjustment by tapping the Adjustments icon again.
- Use Automatic selection on the cleaned layer. With a tight tonal range, a low threshold selects black reliably and the edges are crisp.
You can also use Hue, Saturation, Brightness to drop brightness on the dark tones, or Color Balance to correct a color cast that makes your "black" read blue or brown. Curves is the most controllable of the three because it gives you the histogram.
Once the selection is accurate, you can cut it. Swipe down with three fingers to open the Copy & Paste menu and choose Cut (or Cut & Paste to land it on a new layer). That separates the black from the background without hand-erasing.
Method 4: Select Everything Except Black
Sometimes it's easier to select what you don't want.
- Select the non-black region with Automatic (for example, the white background).
- Tap Invert in the selection menu.
- Check the result. If you used Method 3 first, the inverted selection will be mostly the black elements.
This works well for black line art on a flat white sheet. Select the white once, add any enclosed white pockets (like the inside of letters), then invert.
Common Problems and Fixes
The selection stops at a gap. Automatic selection is contiguous. A tiny break in a line or a white speck splits the region. Use Add mode, or close the gap on a duplicate layer before selecting.
Gray fringes remain after cutting. Raise the threshold slightly, or add a small feather. Alternatively, run Curves on the layer first so the edge pixels are decisively dark or light.
The selection grabs the wrong layer. Automatic selection works from the active layer. If you're tapping on visible black but nothing selects, the artwork is probably on another layer.
You need the black as a mask, not as pixels. Put the black on its own layer and use that layer as the mask source for a clipping mask or for a layer above it. Keeping it as a separate, editable layer is more flexible than a one-time destructive cut.
Getting the Black Out of Procreate and Into Your Pipeline
For motion work, the point of isolating black is usually to use it elsewhere: as a line-art matte, a texture overlay, a stencil, or a reference for animation.
- Hide the background layer and any other layers you don't want in the export.
- Go to Actions > Share and export as PNG to preserve transparency.
If you can't isolate the black cleanly inside Procreate, compositing tools such as After Effects, Premiere Pro, Nuke, and Blender generally offer keying or luminance-based matte options that can handle it.
A rule of thumb: if the black lives on a transparent layer in Procreate, export it clean and skip keying altogether. Keying is a rescue for flattened art, and it always costs some edge quality.
Where Styleframe Fits
Isolating black is often a prep step for a bigger task: turning hand-drawn linework or a flat design into moving, finished footage. That is where is useful as a companion to Procreate and your compositor, not as a substitute for the selection work above.
Styleframe is an AI video and motion tool. One practical way it can connect to a Procreate black-selection workflow:
- Clean linework as a reference: Black line art you've isolated in Procreate can serve as a reference image for a generation, so the drawing you made stays the basis of the result.
You keep your existing compositing workflow and use Styleframe for the generative steps.
Quick Reference: Which Method to Use
Final Tips
- Work on a duplicate layer whenever you use adjustments or cuts. Procreate's undo is quick, but a safe copy is cheaper than redoing a selection.
- Zoom in to at least 200% when checking edges. Fringe problems are invisible at fit-to-screen.
- Keep black elements on their own layer from the start. The cleanest way to "select only black" is never to mix it with other colors on a single layer.
- Export at the canvas size you'll need downstream. Resampling a cut-out later softens the edges you worked to clean.
Once you've set up your layers this way, isolating black in Procreate takes seconds, and the exported files are ready for the rest of your motion pipeline.