How to Select and Delete Procreate
StyleFrame Team7 min read
To select and delete in Procreate, tap the Selection button (the ribbon icon in the top menu), pick a mode such as Freehand or Automatic, and outline the area you want gone. Then swipe down with three fingers to open the Cut/Copy/Paste menu and tap Cut. A three-finger side-to-side scrub clears the selected pixels in one motion, but without an active selection it wipes the whole layer, so check that your selection is live first.
The Quick Version
- Select the layer that holds the artwork you want to remove.
- Tap the Selection button in the top menu.
- Choose a mode: Automatic, Freehand, Rectangle, or Ellipse.
- Define the area. Use Add and Remove to refine it.
- Tap any other tool to commit the selection. The area outside it will show semi-transparent diagonal lines.
- Swipe down with three fingers and tap Cut, or use the three-finger scrub gesture.
Procreate has no dedicated Delete button for selections. That is why the question comes up so often, and why several different methods exist.
Pick the Right Selection Mode
How cleanly your deletion works depends on how well you select. Each mode suits a different kind of cleanup.
Freehand
Freehand is the default. Drag to draw a fluid outline, or tap point to point for straight polygonal edges, and combine both in one selection. It's the best choice for organic shapes, stray marks, or a single element on a crowded layer. While drawing, a two-finger tap undoes your last action and a three-finger tap redoes it.
Rectangle and Ellipse
These modes are for fast, geometric removal: clearing a corner of the canvas, trimming a background block, or knocking out a circular area. Drag a shape around the content and commit.
Automatic
Automatic selects an entire area with a single tap, much like ColorDrop. Tap and hold, then drag left or right to change the threshold. A lower threshold shrinks the selection, and a higher one lets it flow into neighboring areas. Keep tapping other areas to add them. This is the fastest way to remove a flat-color region, such as a fill you want to turn transparent before exporting a PNG.
A useful workflow is to grab the bulk of an area with Automatic, then switch to Freehand to add or remove the awkward edges.
Refining with Add, Remove, and Invert
- Add lets you draw extra areas into the selection. In Freehand, tapping Add a second time closes an unfinished loop. In Automatic it's greyed out because adding is built in.
- Remove cuts down a selection that grabbed too much.
- Invert flips the selection, which is handy when it's easier to select what you want to keep and delete everything else.
Four Ways to Delete a Selection
With a selection committed, you have several options. Which one you use is mostly a matter of taste and how much you trust your gestures.
1. Cut via the three-finger swipe
Swipe down with three fingers anywhere on the canvas to open the Cut/Copy/Paste menu, then tap Cut. The selected pixels disappear from the layer. This is the most reliable method because it's explicit: you see the menu and confirm the action. Cut also puts the content on your clipboard, so you can paste it onto another layer if you change your mind.
2. The three-finger scrub (clear gesture)
With a selection active, scrub three fingers side to side in a zigzag. Only the pixels inside the selection are cleared. It's quicker than Cut, but it carries the biggest risk. Without an active selection, the same gesture clears the entire layer. Some users report deleting more than intended without noticing until later, so check the canvas after each scrub and keep two-finger undo ready.
3. Clear from the Layer Options menu
With your selection active, open the Layers panel, tap the layer's thumbnail to open Layer Options, and choose Clear. It takes more taps, but it's a deliberate action.
4. Transform it out of frame
A workaround some artists prefer is to tap Transform and drag the selected content past the canvas boundary. The content leaves the visible canvas, and you can be sure nothing outside the selection was touched. It isn't elegant, but it's a safe option when precision matters more than speed.
One note on the Selection toolbar's Clear button: it doesn't erase the pixels inside your selection. Users commonly mistake it for a delete action, but it only removes the selection outline. Use one of the four methods above instead.
Deleting by Color or Region
Procreate doesn't have a "erase all of this exact color" command. If you need to knock out a color, such as a white background around line art, the closest approach is:
- Switch to Automatic mode.
- Tap the area you want to remove.
- Hold and drag horizontally to adjust the threshold until the selection covers everything you want and nothing you don't.
- Tap other disconnected regions to add them.
- Swipe down with three fingers and tap Cut.
Check the edges at full zoom. A threshold that's slightly too high will eat into anti-aliased line edges, while one that's too low leaves a fringe of halo pixels. For stubborn fringes, finish with a soft eraser pass or a Freehand selection.
Troubleshooting Common Problems
The whole layer disappeared. The gesture ran without a committed selection, or you selected the wrong layer. Two-finger tap to undo immediately, confirm your selection is visible (the diagonal shading outside it), and try again.
The three-finger gesture isn't registering. The gesture accepts any three fingers touching the screen, including fingers from both hands. If you work with a stylus and a smudge guard glove, make sure at least three fingertips are exposed. The older tap-and-hold menu is no longer available, so the three-finger swipe is the standard way in.
The selection is bigger than it looks. A tiny stray dot far from your main area can stretch the selection's bounds. If the selection seems oversized, that's often why, and Cut will remove those stray bits along with everything else.
Edges look jagged. Hard-edged selections cut hard edges. If you need a softer result, erase the border with a soft brush.
Content disappears from the wrong layer. Selections act on the active layer only. If you keep forgetting, name your layers and lock the ones you're not touching.
Set Up a Dedicated Clear Shortcut
If you delete selections often, don't rely on the default gesture alone. Go to Actions > Prefs > Gesture controls and assign Clear Layer to a gesture of your choice, such as a four-finger tap. Alternatively, set up QuickMenu and include Clear Layer among its shortcuts. A dedicated gesture reduces the chance of triggering the three-finger scrub by accident, and it works well if you're mid-stroke and don't want to reach for the layers panel.
Where This Fits in a Motion Pipeline
Many motion designers, animators, and compositors use Procreate for concept frames, style boards, and hand-painted elements, then bring that artwork into After Effects, Nuke, Blender, or Cinema 4D. Clean selections and deletions matter here because stray pixels, leftover backgrounds, and halo fringes all show up once the art is composited or animated.
A few habits that help:
- Isolate elements on their own layers before exporting, and use Cut to remove overlapping content from each one.
- Clear backgrounds to real transparency, not white fill, if the art will be composited. Export as PNG to keep the alpha channel.
- Check edges against a dark and a light background before sending anything downstream.
Quick Reference
Final Tips
- Always commit your selection by tapping another tool before you delete, so you can see what's actually isolated.
- Prefer Cut when you're unsure, since the clipboard gives you a safety net.
- Use the scrub gesture only when you're confident about your selection, and undo immediately if something looks off.
- Build your deletions around layers: the fewer elements share a layer, the less you'll need precise selections at all.
Once these gestures become muscle memory, selecting and deleting in Procreate takes only a couple of seconds.