How to Select All of One Color in Procreate
StyleFrame Team7 min read
Procreate has no single-tap command that selects every pixel of one color across a whole canvas. The closest method is Automatic Selection: tap Selection, choose Automatic, tap one area of the color, then keep tapping each separate area to add it. Tap and hold after your first tap, then drag left or right to set the threshold so the selection catches near-matching shades without bleeding into neighboring colors.
What Procreate Can and Can't Do
Many artists expect a "select by color" command like the one in Clip Studio Paint. Procreate doesn't have it. Automatic Selection works like a flood fill. It grows outward from the spot you tap, based on color similarity, and you add each disconnected region by tapping it.
On a flat illustration with a few large shapes, that's quick. On artwork with hundreds of scattered specks of the same color, such as halftone dots, stars, or texture flecks, it becomes tedious. You can still get there, but you'll lean on threshold control, layer organization, and sometimes a different tool.
Before you start, check that you're on the right layer. Results depend on which layer is active, so if your linework and your color fills are on separate layers, make the fill layer active before you tap.
Method 1: Automatic Selection
This is the standard approach and works for most jobs.
- Open the layer that contains the color you want.
- Tap the Selection tool.
- Choose Automatic in the selection toolbar.
- Tap the first area of your target color. The selection shows with inverted colors, so a selected blue area looks yellow.
- Tap each additional area of the same color. Each tap adds to the selection.
- When you're done, tap any other tool, such as Brush, Eraser, or Smudge, to commit. Moving diagonal lines around the selected area confirm the selection is active.
From there you can paint inside it, erase it, transform it, or ColorDrop into it.
Tune the Threshold
After your first tap, keep your finger down to bring up the selection threshold. Drag right to expand the selection into similar neighboring tones, and drag left to tighten it.
This matters most on textured or soft-edged art. A low threshold selects only the exact color you tapped, which often leaves a ragged selection full of unselected pixels. A higher threshold absorbs gradients and anti-aliased edges but can spill into adjacent colors. Start low, check the result, and nudge it up a little at a time.
Refine With Other Selection Modes
The Automatic mode is only one part of the selection toolbar. If you've captured most of the color but missed an area, switch to Freehand, Rectangle, or Ellipse and add to your selection manually. Starting with Automatic and finishing with Freehand is often faster than trying to get a perfect result from one tool.
Deal With Edge Halos
The most common frustration is a thin fringe of unselected pixels around shapes. It comes from anti-aliasing: the edge pixels are a blend of two colors, so they fall outside your threshold. Two fixes:
- Raise the threshold slightly until the fringe is included.
- Fill generously, then clean up with an eraser pass.
Method 2: Recolor or ColorDrop When Changing the Color Is the Goal
Often "select all of one color" really means "change that color everywhere." In that case you may not need a selection at all.
Recolor. Procreate's Recolor tool lives in the Quick Menu, which you can set up through the wrench icon > Preferences > Gesture Controls. Once you've assigned it, open the Quick Menu and tap Recolor. A crosshair appears on the canvas. Drag it onto the color you want to change, then pick a new color from the Color panel. The change updates live as you adjust the color. If the whole background shifts instead of your object, the crosshair is probably sitting in the wrong spot, so move it. The flood threshold slider at the bottom controls how much area is covered.
ColorDrop. Drag the active color from the top-right swatch onto a closed shape to fill it. Holding before you release lets you adjust the threshold, which works like Automatic Selection. This is useful for flat art with clean boundaries.
Both approaches are faster than selecting and filling by hand, but they're destructive to the layer's pixels. Duplicate the layer first if you might want to go back.
Method 3: Isolate One Color on Its Own Layer
If you plan to adjust, animate, or export a color separately, move it to a new layer.
- Use Automatic Selection to select the color across all of its regions.
- Swipe down with three fingers to open the Copy & Paste menu.
- Choose Cut, then paste the pixels onto a new layer.
The color now sits on its own layer, ready for opacity changes, blend modes, or adjustments without touching the rest of the artwork.
To remove a color instead, select it and use Cut, or use the three-finger scrub gesture to clear the selected area. Procreate's Clear button in the selection toolbar only dismisses the selection outline and doesn't erase anything, which trips up many people. A tool that erases an exact color across the whole canvas isn't directly planned, though future improvements might lend themselves to the idea, so this select-then-cut route is the way to do it.
Troubleshooting Common Problems
Only part of the color gets selected. The areas may be separated by a different color, or the layer may include slight variations. Raise the threshold, or add the missed areas with another tap.
The selection leaks into other colors. Your threshold is too high. Drag left, or undo and tap again.
Nothing selects the way you expect. Confirm the active layer. If your artwork is spread across several layers, merge them with a duplicate first, or work layer by layer.
Thin lines get skipped. Automatic Selection can struggle with hairline strokes. Use a lower threshold and tap closer to the stroke, or add the strokes with Freehand.
Texture or noise breaks up the selection. Photographic or grainy art doesn't behave like flat color. Consider a different tool for the color isolation, or flatten the colors first.
Taking Procreate Color Work Into After Effects and Nuke
If you use Procreate for storyboards, styleframes, or illustrated assets that end up in a motion pipeline, color isolation can happen on either side of the export.
The cleanest approach is to separate colors in Procreate before you export. Cut each important color group to its own layer, then export the layers in a format your compositing software can read. Separate layers are easier to animate downstream than a flattened image, which may need keying or masking.
If you only have a flattened image, you can still isolate color downstream, since compositing tools generally offer keying or color-range options for pulling a matte from a specific hue.
The tradeoff is precision. Pulling a matte from a flat PNG will always be less exact than selecting while the layers are still separate, especially at anti-aliased edges. If you know you'll need a color isolated later, do it in Procreate first.
When the Color Job Is Really a Style Job
Sometimes selecting one color is a step toward a bigger goal: restyling a frame, building a consistent palette across a sequence, or turning a sketch into something more finished. Procreate is good for the drawing and selection part, but it isn't built to carry a look across moving shots.
That's where can sit beside your illustration tools. Your compositing workflow stays the same, and Procreate stays where it's strongest, in hand-built art and precise color decisions.
Quick Reference
FAQ
Can Procreate select every instance of a color in one tap? No. You tap each separate area with Automatic Selection, though threshold adjustment lets one tap capture many similar shades.
Does Automatic Selection work across layers? Results depend on the active layer, so merge or duplicate and flatten layers if the color you need is spread across several.
Why does Clear not erase my selection? Clear removes the selection outline only. To erase the contents, use Cut or the three-finger scrub gesture.
Should I isolate colors in Procreate or in After Effects? Isolate them in Procreate when you can. Separate layers give cleaner edges than keying a flattened image later.