How to Remove Reference Picture in Procreate Time Lapse
StyleFrame Team7 min read
You can't remove a reference picture from a Procreate time-lapse after it has been recorded, because Procreate stores every undoable action as a frame and stitches them together on export. Deleting the layer doesn't help, since the import and the deletion are both part of the recording. To keep a reference out of the video, mark its layer as a Private Layer, which is excluded from the exported time-lapse and the replay, or pause recording while you bring it in. If the footage already exists, you have to fix it in a video editor.
Why deleting the layer doesn't work
A common first instinct is to import the photo, trace over it, delete the layer, and assume the video will look clean. It won't. Procreate's team has explained that the time-lapse is built from every undoable action, so a layer that appeared and then vanished still appears and vanishes in the export. There is no per-layer "scrub from history" option.
This is why users keep asking for a "hide reference from time-lapse" toggle. The reasons are practical:
- A canvas full of reference photos spoils the sense of mystery in a process video.
- Layers that pop in and out look random and distracting.
- Some references are simply off-brand or irrelevant to the audience.
- Commercial uses, such as live-event walk-in screens or explainer sketches, need only the drawing itself.
The workarounds below address most of these cases. The best ones need to happen before or during the drawing session, not after.
Method 1: Use a Private Layer for the reference
A Private Layer is the cleanest fix when the reference has to live on the canvas as a layer. It behaves like a normal layer in every respect, so you can move it, scale it, change opacity, and trace over it. The difference is that it doesn't show up in the Gallery preview image, the exported time-lapse video, or the replay.
Steps:
- Create a new layer and import your reference photo into it.
- Open that layer's options and set it as a Private Layer. The exact menu location can vary between Procreate versions, so check the current Handbook if you can't find it.
- Draw on separate, normal layers above it.
- Run Time-lapse Replay before you export to confirm the reference isn't visible.
Make the layer private before you start drawing, and do a quick test on a throwaway canvas the first time. Since the recording is built from your actions, you want to confirm how your version handles the reference before committing hours of work to it.
Method 2: Pause time-lapse recording while you set up
Procreate lets you stop and restart recording at any point, which is useful for editing your process in-camera.
- Tap Actions, then Video.
- Toggle Time-lapse Recording off.
- When Procreate asks about purging the existing video, choose Don't Purge if you only want a pause. Purge deletes all video recorded on that canvas so far and can't be undone.
- Import the reference, resize it, and do any setup you don't want in the final video.
- Toggle Time-lapse Recording back on to continue.
This approach hides the import step, but there's a catch. Once you resume recording, any frame that still shows the reference will appear in the video. If the reference stays visible while you draw, it will be in the footage. Use pausing to hide setup, cleanup, or messy experiments, and use Private Layers to keep a reference out of the picture during active drawing.
Be careful with the Purge option. If you toggle recording off to hide a reference and tap Purge by mistake, you lose everything already captured.
Method 3: Set recording options before you begin
Time-lapse is on by default for new canvases, recording at 1080p on the Good Quality setting. These settings can't be changed mid-project, so decide up front. If this piece is going into a motion project, a custom canvas lets you choose a resolution from 1080p to 4K and a quality setting from Low to Lossless. HEVC is off by default.
This matters for reference removal in one way: if you plan to clean up the footage in a video editor, higher-quality source gives you more room to mask, crop, or retouch without visible compression artifacts. Export the full-length version rather than the 30-second cut if you plan to edit, because the 30-second option drops frames algorithmically, and you may lose frames you wanted to keep.
If the footage is already recorded
When the reference was visible during recording, you can't extract it from Procreate. You have a few options, depending on how much of the video it affects.
Trim or cut the sections
If the reference appears only during the import and setup phase, export the full-length video and trim those moments in your editor. A video editor such as iMovie on the iPad can handle this. Procreate's own team suggests editing the exported video in your preferred video editor.
Mask or cover the reference area
If the reference sits in a consistent spot, such as a corner or beside the drawing, you can often crop in or mask over it. In After Effects:
- Import the time-lapse and place it in a composition.
- Scale and reposition to crop the reference out of frame, or draw a mask around the artwork area.
- Add a clean background or matte behind it.
- Use time remapping to speed through any dead stretches.
This works when the reference doesn't overlap the drawing. If the artwork sits directly over the photo, masking won't help, because the photo is part of the pixels you're keeping.
Rebuild the reveal from exported layers
When the reference is baked into the footage, the most reliable fix is to rebuild the process video yourself. Export your layers from Procreate, import them into After Effects, and animate the reveal using wipes, trim paths, or layer opacity. You lose the authentic stroke-by-stroke order, but you gain full control over pacing, framing, and what appears on screen. This is essentially what the forum posters asking for "a one-stop-shop" were working around with Photoshop plus After Effects.
Choosing the right approach
A note on honesty in process videos
Some Procreate users argue that hiding references defeats the point of a time-lapse, since the video is meant to show your real process. That concern is legitimate for artists posting to a community that values authentic workflow. Others point out that blend modes, layers, and unlimited colors are tools too, and that professional use cases like live events, presentations, and branded content have different needs than a portfolio share.
If you're posting publicly, consider mentioning in the caption that you worked from a reference. It costs nothing and keeps trust with your audience. For client work, the decision is simply what the deliverable needs.
Quick checklist before you export
- Confirm reference layers are set as Private Layers.
- Run Time-lapse Replay and scrub through the whole thing.
- Check that nothing is hiding in the first and last few seconds.
- Choose Full length if you plan to edit, or 30 Seconds for a quick share.
- Export to Files and keep a copy of the layered project.
Planning where the reference lives before you draw a single stroke saves more time than any after-the-fact fix, because Procreate's recording can't be edited retroactively. Set up the Private Layer first, test once, and your time-lapse will come out clean.