How to Remove Color Procreate
StyleFrame Team7 min read
To remove a color in Procreate, open Selection, choose Automatic, tap the color and drag to set the threshold, then Cut or clear the selected pixels so they become transparent. To strip color without erasing pixels, use Adjustments: Hue, Saturation, Brightness to desaturate, or clip a layer above the artwork and set it to Subtract to take out one color. Which method you want depends on whether you need transparency, a black-and-white image, or one hue taken out of a still-colored image.
Which "remove color" do you mean?
Procreate has no single "erase by color" command. Users have asked for one, and the Procreate team has said it isn't directly planned. Instead, the app gives you several tools that each solve a different version of the problem:
- Make a color transparent (for example, knocking a flat background out of a JPEG): Automatic Selection, then Cut.
- Take one hue out of an image while keeping the rest: a clipping mask with Subtract blend mode.
- Remove all color: desaturate with Hue, Saturation, Brightness.
- Swap a color for another: the Recolor tool, or Color Balance and Curves for broader shifts.
Picking the right one first saves a lot of undo-ing.
Method 1: Erase a color to transparency with Automatic Selection
This is the closest Procreate gets to a color-based eraser, and it's the best fit when you have a flat-colored area (a white or yellow background, say) that you want gone before exporting a PNG.
- Select the layer that holds the color you want to remove. Check this first. It's the most common mistake when you have many layers.
- Tap the Selection tool and choose Automatic at the bottom of the screen.
- Tap and hold on the color you want to remove, then slide your finger left or right. This sets the selection threshold. A low threshold grabs only near-identical pixels. A higher one pulls in similar shades.
- Lift your finger and check the marching-ants outline. If it misses areas, switch to Add and tap again.
- Swipe down with three fingers to open the Copy & Paste menu and choose Cut. The selected pixels vanish and the layer becomes transparent there.
A few notes that trip people up:
- The toolbar's Clear button doesn't delete pixels. Users in Procreate's own suggestion forum have run into this: it dismisses the selection outline rather than erasing what's inside. To erase, use Cut, or scrub three fingers across the canvas, which clears the layer. With an active selection, that scrub only clears the selected area.
- Automatic Selection works on contiguous regions. If the same color appears in separate islands, such as the white inside letterforms, you'll need to add each one with Add mode or tap them individually.
- JPEG source files have compression noise, so a "flat" color is really a spread of nearly identical values. Raise the threshold until the selection covers the whole area, then use Feather on the selection to soften the edge before cutting. That avoids a harsh, jagged cutout.
- When you export, hide any background layer and choose PNG so the transparency survives.
Method 2: Remove one color with a Subtract clipping mask
If you want to pull one color out of an image while leaving everything else visible, you can use blend modes instead of selections:
- Add a new layer directly above the artwork.
- Tap the layer and choose Clipping Mask, so the effect applies only to the layer below.
- Pick the color you want to remove and fill the clipping layer with it.
- Tap the N on the layer and set its blend mode to Subtract.
The color you filled with gets subtracted from the layer beneath it. In a demonstration using a multicolored Easter egg, this removed the red, and repeating the process with green or blue produced versions with those channels taken out. To keep different results, duplicate the original artwork first and apply a separate clipping layer to each copy.
Keep the math in mind. Subtract works on color values, not on a perceptual "this is the red part" selection. It behaves most predictably with pure, saturated colors, and it can shift neighboring colors that share channel values. It also leaves pixels in place, so you get a recolored image, not transparency. For a clean knockout, use Method 1.
Method 3: Remove all color by desaturating
To convert artwork to grayscale:
- Select the layer.
- Tap Adjustments (the magic wand icon) and choose Hue, Saturation, Brightness.
- Drag Saturation all the way left. Moving it toward the left desaturates toward gray.
- Tap the Adjustments icon again, or choose another tool, to commit. A two-finger tap undoes the change.
Adjustments apply to the active layer only, so if your piece spans multiple layers, either merge a copy or group and flatten before adjusting. If you want more than a flat desaturation, Curves gives you finer control over color and contrast over a histogram. Color Balance splits shifts across shadows, midtones, and highlights. Midtones are selected by default and tend to give the most even result.
Method 4: Replace a color with Recolor
Sometimes "remove" really means "change." Recolor swaps the color of a region in real time using whatever color you have active:
- Open your Quick Menu. If Recolor isn't there, assign it through the wrench icon, then Preferences, then Gesture controls.
- Select the correct layer and trigger Recolor. A small crosshair appears.
- Drag the crosshair onto the area you want to change. If the whole background changes, the crosshair is sitting on the wrong spot.
- Adjust the flood threshold at the bottom of the screen if Recolor isn't covering everything, or is spilling too far.
Recolor works best on flat or lightly textured areas. On heavily textured layers, the result shifts as you move the crosshair, which makes it good for exploration and less reliable for precision work. If you need to "remove" a color by recoloring it to match the surrounding background, this is a fast path, but it won't give you real transparency.
Troubleshooting common problems
- White or colored halos around the edges after cutting. The edge pixels were blends of the removed color and the artwork. Increase threshold slightly, feather the selection, or clean the rim with a soft eraser on a duplicate layer.
- Selection grabs too much. Lower the threshold, or work on a duplicate of the layer so you can compare.
- Nothing happens when you cut. You may be on the wrong layer, or the layer may be locked or have Alpha Lock turned on.
- The result looks different when exported. Check that the background layer is hidden and that you chose PNG, not JPEG, which has no transparency.
Work on a duplicate layer whenever you can. All of these edits are destructive on the pixels once you commit them and move on.
Taking Procreate artwork into a motion pipeline
If the artwork is headed for a video or compositing workflow, you often don't need to finish the color removal in Procreate at all. Export the flat artwork and do the keying in your compositor, where the result stays adjustable.
A good rule is to do the cut in Procreate only when you need a clean PNG asset to hand off. If the color treatment is part of the look, keep it adjustable downstream.
Quick reference
Start with Automatic Selection for transparency and Subtract or desaturation for color treatment. Hand off anything that still needs flexibility to your compositor.