How to Remove All of One Color in Procreate
StyleFrame Team7 min read
Procreate has no single "delete this color" button, but you can get the same result in a few taps. To make one color transparent, use Selection > Automatic: tap and hold the color, drag to set the threshold, then three-finger swipe down and choose Cut. To strip a color's influence from a flattened image without making it transparent, put a clipping-mask layer filled with that color above the artwork and set its blend mode to Subtract.
Which method is right depends on what "remove" means for your job. You might want transparent pixels for a PNG that goes into a composite, or you might want to take a color out of the image itself. The sections below cover both, plus the edge problems that show up once the file is in After Effects or Nuke.
Method 1: Remove a color to transparency with Automatic Selection
This is the method to use when you have flat artwork, a JPEG with a solid background, or a logo you need to isolate. Automatic Selection is the closest thing Procreate has to a magic wand.
- Select the layer that holds the color you want gone.
- Tap the Selection tool (the S icon) and choose Automatic in the bottom bar.
- Tap and hold on the color. Keep your finger down and slide left or right to adjust the threshold. A higher threshold pulls in more similar shades.
- Lift your finger. The selected area is now marked.
- Swipe down with three fingers to open the Copy & Paste menu and tap Cut. Alternatively, use the Clear Layer gesture (a three-finger scrub back and forth), which clears only the selected area when a selection is active.
The "Clear" button inside the Selection toolbar is easy to misread. It removes the selection outline, not the pixels. Deleting pixels is the job of Cut or the scrub gesture.
When the color is in several disconnected places
Automatic Selection tends to grab a connected region of similar color. If the same color appears in several separate pockets, such as the counters of letters or gaps in line art, switch the selection mode to Add and tap each region in turn. Cutting after each pass also works, and it lets you vary the threshold per region.
Procreate has no built-in "select this color everywhere on the canvas" command comparable to Clip Studio Paint's color selection. Procreate's own feedback forum has requests for one, so check your current version's handbook in case that has changed.
Clean up the edges before you cut
Selections on anti-aliased art almost always leave a fringe. Before you cut:
- Raise the threshold slightly so the soft edge pixels are included in the selection.
- Use Feather from the selection toolbar for a gentler edge, especially on photographic or painterly work.
- Expect JPEG noise. Compression artifacts create near-matching pixels around edges that a low threshold will skip, leaving speckles. A higher threshold or a second pass in Add mode usually fixes it.
If the result still has a halo, cut the selection, then Invert it and nudge the remaining edge with a small eraser pass. Don't over-feather. A heavily feathered cut on line art turns crisp strokes into mush.
Method 2: Subtract a color with a clipping mask
If the goal is to pull one color out of the image itself, a blend-mode trick works without any selection. It's useful for color-separation looks and for isolating channels.
- Duplicate your artwork layer so you keep an untouched original.
- Add a new layer above it and set it as a Clipping Mask, so it only affects the layer below.
- Pick the color you want to remove and fill the clipping layer with it (drag the color from the swatch onto the layer, or use ColorDrop).
- Tap the N on that layer and set the blend mode to Subtract.
Subtract works on color values, so it removes that color's amount from every pixel underneath. Pixels that exactly match the filled color drop toward black, and other pixels shift too. That makes it a good fit for flat, saturated colors, such as removing the red from a mostly red-green-blue graphic. For photographs and gradients, expect color shifts in areas you didn't intend to touch.
You can stack more clipping layers to remove several colors, or duplicate the original and run the process with different colors for variants. Once you're happy, merge down. If you need real transparency afterward, run Method 1 on the black areas that remain.
Method 3: Get close with Adjustments
Sometimes you don't need the color fully gone, just neutralized or pushed out of the way.
- Hue, Saturation, Brightness lets you pull overall saturation down on a layer or selection. Combined with a selection, it can turn one region gray without touching the rest.
- Color Balance shifts the mix of red, green, and blue across shadows, midtones, and highlights. Pushing a slider toward the opposite color suppresses a cast.
- Curves gives you detailed control over color and contrast. Pulling down the red part of the curve removes red from the image tonally, which is a cleaner approach than Subtract for photographic material.
These adjustments are non-destructive only if you keep a duplicate layer, because Procreate applies them to the layer you're working on. Duplicate first.
Easy special case: removing white or black backgrounds
If the color you want to remove is a white background behind dark line art, you can skip selection entirely. Set the line art layer's blend mode to Multiply and the white effectively disappears over whatever sits underneath. For black backgrounds behind glowing or light elements, Screen does the equivalent. This is a blend, not true transparency, so the pixels are still there. For export, convert it to real alpha using Method 1, or flatten against your target background.
Exporting for After Effects, Premiere Pro, Cinema 4D, Blender, and Nuke
Once the color is gone, how you export decides whether the cleanup survives your pipeline.
- PNG keeps transparency and is the simplest hand-off. Check the layer thumbnails before exporting: if the checkerboard shows through, the alpha is real.
- PSD preserves layers, which is handy if you want to rebuild or re-cut in your compositing app. Blend modes may not translate exactly, so verify the result against Procreate's view.
- Hide the background layer before exporting PNG, or you'll get the fill you thought you removed.
- Watch for fringes. Edges can carry color from the old background. If you see a white or colored halo in your compositing app, try choking or eroding the matte edge by a pixel.
If you have a lot of flat art or scans to process, doing the color removal in your compositor can be faster than in Procreate, since compositing apps generally include keying tools. Procreate is best when the cleanup is part of the drawing process, and a keyer is better for batches or for footage.
Troubleshooting common problems
The selection grabs too much. Lower the threshold, or switch to Remove mode and tap the areas you want to exclude.
Only part of the color disappears. The color probably has slightly varying values, as happens in JPEGs, textures, and anti-aliased edges. Raise the threshold or add selections.
Cut does nothing. Check that you're on the right layer and that it isn't locked or set to Alpha Lock. Alpha Lock stops pixels from being erased.
The edges look jagged. Add a small amount of feather, or redraw the edge on a new layer rather than relying on the selection.
You need the cut to be reversible. Duplicate the layer first, or add a Layer Mask and paint on the mask instead of deleting pixels.
Quick reference
For most artwork, Automatic Selection plus a slightly raised threshold and a quick edge check is the answer. Reach for Subtract when you want the color out of the image rather than out of the alpha, and hand batch work to a keyer.