How to Reduce Transparency in Procreate
StyleFrame Team5 min read
To reduce transparency in Procreate, open the Layers panel, tap the "N" next to the layer, and drag the Opacity slider to the left. You can also tap the layer with two fingers and slide your finger or Apple Pencil across the top of the screen. For a brush, drag the lower slider in the sidebar down. For one area of a layer, make a selection first, then two-finger tap the layer and slide left.
One caveat on terminology: "reduce transparency" is ambiguous. Most people searching it want to make something less see-through, which means raising opacity. Others want the opposite, a fainter layer or stroke. This guide covers both directions, since each uses the same controls.
Opacity vs. transparency: which way are you going?
In Procreate, opacity describes how visible pixels are. At 100% a layer is fully solid, and at 50% it's half see-through. Transparency is the inverse, so:
- To reduce transparency (make it more solid), increase opacity toward 100%.
- To reduce opacity (make it more see-through), decrease the slider toward 0%.
Procreate applies this to three targets: the brush, the whole layer, and a selection. Each behaves differently, and mixing them up is the most common source of "why isn't this working" moments.
Method 1: Change layer opacity (non-destructive)
This is the right choice when you want to fade or solidify an entire layer and stay able to change it later.
Option A: the layer menu
- Tap the Layers icon in the top right.
- Tap the small letter to the right of the layer name. It's "N" for Normal by default.
- Drag the Opacity slider at the top of that menu. The percentage shows beside it.
This menu also holds the blend modes, so it's convenient if you're tuning mode and opacity together.
Option B: the two-finger tap
- Open the Layers panel.
- Tap the target layer with two fingers at once. An opacity slider appears at the top of the canvas.
- Slide left to decrease opacity or right to increase it.
Layer opacity is non-destructive. The underlying pixels never change, so you can return to the slider and adjust again whenever you like. That matters for animation and compositing work, where a layer you faded at 40% on Monday may need to be 65% on Thursday.
Method 2: Change brush opacity
Layer opacity affects what's already painted. Brush opacity affects what you paint next.
- Select a brush.
- Drag the lower slider in the sidebar. Up increases opacity and down decreases it.
It's easy to grab the wrong slider, so make sure you're using the lower one.
If your brush looks too faint even at maximum opacity, the cause is often pressure sensitivity rather than the slider. Many brushes map Apple Pencil pressure to opacity, so a light touch produces a see-through stroke regardless of where the sidebar slider sits. Press harder, or check your pressure settings so light strokes stay more solid.
Method 3: Change opacity on a selection (destructive)
Sometimes you only want part of a layer to fade, such as a highlight, one character's limb, or a single shape on a busy layer.
- Open Selections and pick a method.
- Make your selection.
- Open the Layers panel and tap the layer holding the paint with two fingers at once.
- Slide left on the canvas to decrease opacity or right to increase it.
Two cautions. First, the selection-opacity change is applied when you exit the mode, and it's destructive. You can undo immediately, but you can't revisit the value later the way you can with a layer slider. Second, if the two-finger tap on the layer isn't doing what you expect, check that you're tapping the layer in the Layers panel, not the canvas. If two-finger tap to undo is turned on in your gesture settings, tapping the canvas with two fingers will undo, which is why people sometimes see strokes disappear instead of an opacity slider.
If you want the selection fade to remain adjustable, duplicate the layer first, or cut the selection onto its own layer and use ordinary layer opacity there.
Troubleshooting: opacity isn't changing the way you expect
That last case is worth understanding. Raising layer opacity to 100% only makes the layer as solid as its pixels allow. If you painted with a 30% brush, those strokes stay at 30% density inside the layer. Duplicating the layer and merging the copy down stacks the pixels and builds density. Repainting at a higher brush opacity is cleaner when you can.
Making semi-transparent art solid: a few practical tricks
- Duplicate and merge. Stacking copies of a layer increases pixel density without repainting.
- Use a solid backing layer. Place a fully opaque fill beneath a faded layer to keep your artwork from showing the canvas or other layers through it.
Quick reference
- Layer, adjustable later: Layers → "N" → Opacity slider, or two-finger tap the layer.
- Brush: Lower sidebar slider; check pressure settings if strokes look faint.
- Selection: Make a selection → two-finger tap the layer → slide left or right. This is destructive.
- More solid, not less: Raise opacity to 100%, then duplicate and merge if the pixels themselves are semi-transparent.
Once you know which of the three targets you're adjusting, most opacity problems in Procreate come down to a simple check: whether you're working on the brush, the layer, or a selection.