How to Reduce Opacity of Layer in Procreate
StyleFrame Team7 min read
To reduce the opacity of a layer in Procreate, open the Layers panel, tap the small letter to the right of the layer name (usually "N" for Normal), and drag the Opacity slider to the left. This method is non-destructive, so you can change the value again at any time. If you need to fade only part of a layer, make a selection, tap the layer with two fingers, and slide left on the canvas. That second method is destructive, because the new value is baked into the pixels once you exit.
Method 1: Use the layer opacity slider (non-destructive)
This is the method to use most of the time.
- Tap the Layers icon in the top right of the canvas.
- Find the layer you want to change.
- Tap the small letter or letters to the right of the layer name. By default this is N, for Normal blend mode.
- Drag the Opacity slider beneath the blend mode list to the left to reduce opacity, or to the right to increase it.
Because the slider only sets a property on the layer and never rewrites its pixels, you can return to 100% whenever you want and get the original artwork back. The layer opacity applies to the whole layer, even if you have an active selection.
A few details help here:
- The same panel holds the blend mode list, so you can set opacity and blend mode in one visit.
- Opacity applies to the layer's contents as a whole.
- If you need finer control than a thumb drag gives you, try dragging the slider with the Apple Pencil, or make small adjustments and check the percentage readout.
Method 2: Two-finger tap on the layer (destructive, works with selections)
The other common method is a gesture-based adjustment, and many illustrators have it in muscle memory.
- Open the Layers panel.
- Tap the layer with two fingers at the same time. A blue bar labelled "Slide to adjust" appears at the top of the screen.
- Slide a finger left on the canvas to reduce opacity, or right to increase it.
- Exit the mode to commit the change.
Two points trip people up:
- The blue bar is a readout, not a slider. Dragging on it does nothing. Slide on the canvas itself.
- The change is permanent once committed. Unlike the layer slider, this adjustment rewrites the pixel data. The new, lower opacity becomes the layer's new 100%. You can undo straight after applying, but you can't keep re-tuning it across a project.
If you have a selection active when you use this method, the opacity change applies only to the selected area. That makes it useful for fading one part of a layer without splitting it. If you want to keep your options open, duplicate the layer first and run the destructive adjustment on the copy.
Method 3: Reduce opacity of only part of a layer
Sometimes you don't want the whole layer to fade. You have a few options:
Selection-based fade. Use the Selection tool to isolate the area. Then use the two-finger tap on the layer in the Layers panel and slide on the canvas. Only the selected pixels change. This is destructive, so work on a duplicate when you can.
Layer mask. Add a mask to the layer and paint with black, white, or grays to hide or reveal parts of it. Masks are the non-destructive way to partially fade a layer, because you can repaint them at any time.
Split the layer. Cut the selected area to a new layer, then use the normal layer opacity slider on each piece. This keeps both pieces adjustable and doesn't need a mask.
Method 4: Add a QuickMenu shortcut
If you reduce opacity often, you can assign it to QuickMenu so it's available on the canvas without opening the Layers panel.
- Open Gesture controls and set up the QuickMenu gesture, for example touch-and-hold.
- Assign a Layer Opacity action to one of the QuickMenu slots.
- Trigger QuickMenu on the canvas and slide to adjust.
A caution: despite the name, this action behaves like the two-finger adjustment, not like the layer slider. With an active selection, it changes only the selection. And like the two-finger method, it commits a destructive change. If you want the non-destructive route, use the slider in the Layers panel.
Brush opacity vs. layer opacity
These get confused constantly, and mixing them up is a common reason a result looks wrong.
- Brush opacity is the lower slider in the sidebar. It controls how opaque new strokes are. It does nothing to marks you have already made.
- Layer opacity controls the visibility of everything already on a layer.
Two related issues:
- Many brushes respond to Apple Pencil pressure. If your brush opacity is at maximum but strokes still look faint, pressure response is likely the cause, and you should check your pressure settings.
- If you're painting on a clipping mask, strokes only show where the layer beneath has content. A stroke that "doesn't appear" over empty areas may be working as intended.
Troubleshooting: when opacity won't change
If you can't get a value to change, check these in order:
- Are you dragging the blue bar? In the two-finger method, slide on the canvas, not on the bar.
- Is two-finger tap undoing your last stroke? If you have two-finger tap to undo enabled in Gesture controls, tapping the canvas can trigger undo. Make sure you tap the layer in the Layers panel, not the canvas.
- Looking for Adjustments > Opacity? Older versions of Procreate had an Opacity entry in the Adjustments menu. It was removed in later versions, so you now use the Layers panel or a QuickMenu action instead.
- Try a hard restart of the iPad. Gestures can occasionally stop responding properly, and a full restart is a quick first fix.
- Check your gesture settings. If the two-finger gesture works on one device but not another, compare the Gesture controls settings.
Carrying Procreate opacity into a motion workflow
If you're a motion designer or animator, Procreate is often a source for textures, character art, storyboards, and style frames rather than a final destination. A few habits make the handoff cleaner:
- Prefer the non-destructive slider and masks for anything you might want to tweak later. Baked-in opacity is hard to reverse once the file is in After Effects.
- Name and organize layers before export, so they are easy to find in your compositing app.
- Check your export. Export a PSD and open it in After Effects or Photoshop to confirm that layer opacity and blend modes came across as you expect. Do a quick test on a small file before committing a full project.
- Keep a flattened PNG or high-resolution export alongside the layered file as a reference for how the piece should look.
- Decide where opacity lives. For anything that will animate, such as a fade-in, it's usually better to leave the layer at full opacity in Procreate and keyframe opacity in After Effects, where you get timeline control and easing.
Quick reference
For most work, use the slider in the Layers panel and reach for masks when you need partial fades. Save the two-finger gesture for quick, deliberate adjustments, preferably on a duplicate layer.