How to Reduce Opacity of Image in Procreate
StyleFrame Team5 min read
To reduce the opacity of an image in Procreate, open the Layers panel, tap the N next to the image's layer, and drag the Opacity slider to the left. A faster route is to tap the layer with two fingers and slide your finger left on the canvas to lower the percentage. Both methods are non-destructive, so you can change the value again later without losing pixels.
Before You Start: Get the Image Onto Its Own Layer
Opacity in Procreate applies to a layer, a selection, or a brush. If your image isn't on its own layer, you can't fade it independently of everything else.
Insert your image into the canvas so that it sits on its own layer above your current one.
If the image is already merged into a painted layer, fading that layer fades everything on it. In that case, select the image area and copy it to a new layer first.
Method 1: The Layer Opacity Slider (Most Precise)
This method works best when you need a specific percentage.
- Tap the Layers icon in the top right.
- Find the image layer.
- Tap the small letter to the right of the layer name. It reads N by default.
- Drag the Opacity slider left to make the image more transparent, or right to make it more solid.
The panel also lists the blend modes, so you can change the mode and the opacity in one visit. Lowering opacity here doesn't alter the underlying pixels. Return and set it back to 100% at any point.
Method 2: Two-Finger Tap on the Layer (Fastest)
- Open the Layers panel.
- Tap the image layer with two fingers at the same time.
- A slider appears at the top of the screen with a percentage readout.
- Slide your finger or Apple Pencil left to reduce opacity, right to increase it.
This is the quicker method when you're eyeballing a fade against other artwork, because the canvas stays in view while you adjust. The percentage readout still lets you land on a number such as 35% if you need to match another layer.
Method 3: Adjustments > Opacity
The Adjustments menu has its own Opacity tool.
- Select the layer you want to change.
- Tap the Adjustments icon and choose Opacity.
- Slide left or right with your finger anywhere on the canvas. A bar at the top shows the current value.
- Tap the Adjustments icon again, or choose another tool, to commit the change.
The bottom of the interface has buttons to cancel, undo, redo, and reset your changes. Unlike the layer slider, this adjustment is applied once you commit. If you may want to revisit the value, use Method 1 or 2 instead.
Method 4: Reduce Opacity on Just Part of an Image
Sometimes you only want to fade a region, such as one corner of a photo.
- Open Selections and choose a selection method.
- Make your selection on the image.
- Open the Layers panel and tap the layer with two fingers.
- Slide left on the canvas to reduce the opacity of only the selected area.
Once you exit this mode, the change is applied permanently to those pixels. You can undo it right away, but you can't tweak it repeatedly the way you can with the layer slider.
Method 5: Lower Brush Opacity (For Painted Marks, Not Images)
If you're painting rather than fading an inserted image, the brush has its own opacity control. Select a brush and drag the lower slider on the sidebar down to reduce its opacity. Many brushes also respond to Apple Pencil pressure, so a brush can look more transparent than the slider suggests. If your strokes seem too faint with the slider at maximum, pressure sensitivity is a likely cause.
This control affects new strokes only. It won't change an image you've already placed.
Which Method Should You Use?
Common Problems and Fixes
The slider doesn't seem to affect my image. Check that the correct layer is active. Opacity changes apply only to the selected layer.
The image looks faded but I didn't change opacity. A blend mode other than Normal can change how a layer looks regardless of the slider. Tap the letter next to the layer name and check the mode.
The fade looks uneven. A selection may be limiting the change. Deselect and try again.
Two overlapping layers look muddy at partial opacity. Both layers show through each other. Try reducing opacity on only the layer that should recede.
Taking Faded Procreate Artwork Into a Motion Pipeline
For motion designers and compositors, Procreate is often a quick place to build textures, overlays, matte paintings, or hand-drawn elements. Setting opacity in Procreate is fine for look development, but keep a few habits in mind for production:
- Export layered when you can. This lets you rebuild the stack in your compositor and keep opacity as an adjustable property rather than a baked decision.
- Set final opacity in your compositor. If a layer will fade over time, keyframe opacity in After Effects, Premiere Pro, or Nuke rather than baking a static value in Procreate.
- Export at full opacity when the element will be reused. A full-opacity export with transparency gives you more flexibility than a pre-faded version.
- Use the fade as a reference. If you're testing how strong an overlay should be, note the percentage and recreate it in your compositing package.
Quick Recap
- Reduce image opacity by tapping N on its layer and dragging the slider, or by tapping the layer with two fingers and sliding on the canvas.
- Use Adjustments > Opacity for a committed, one-time change.
- Use selections for partial fades, but know they are destructive.
- Finish animated fades in your compositing app.
With the layer slider covered, you can handle most fades in Procreate and hand clean, flexible assets to the rest of your pipeline.