How to Recolor Lines in Procreate
StyleFrame Team7 min read
To recolor lines in Procreate, put the lines on their own layer, turn on Alpha Lock, pick a new color, then tap the layer and choose Fill Layer. Alpha Lock confines the fill to pixels that already exist, so the line shape stays intact. If your lines are merged with the colors, select the line pixels, copy them to a new layer, and run the same steps on that layer.
Method 1: Recolor lines that are on their own layer
This is the cleanest approach and the one to build your files around. It is quick.
- Open the Layers panel and select the layer that holds your line art.
- Turn on Alpha Lock. Swipe left on the layer and tap Alpha Lock, or tap the layer and choose it from the menu. A small blue indicator lights up on the layer when it is active.
- Pick your new color from the Color panel.
- Tap the layer again and choose Fill Layer. Every non-transparent pixel on that layer takes the new color.
- Turn Alpha Lock off if you want to keep drawing normally on that layer. Leaving it on means new strokes only land on existing pixels.
Zoom in afterward and check the edges. With Alpha Lock on, the fill stays confined to the existing line pixels, and no black pixels should be left over.
If you skip step 2, Fill Layer floods the entire layer with the color, which is the most common mistake. Undo with a two-finger tap and try again.
Method 2: Recolor lines that are merged with your fills
Sometimes the outline and the color are flattened onto one layer. You can still isolate the lines without redrawing anything.
- Open the Selection tool and set it to Automatic.
- Choose a contrasting color in the Color panel that differs clearly from your line color.
- Tap and hold on a line, then drag with your finger or Apple Pencil to adjust the threshold. Dragging right widens the selection, dragging left narrows it. Stop when all the line pixels are selected and the fills are not.
- Copy the selection from the Actions (wrench) menu, then add a new layer and paste. You now have a line-only layer sitting above your artwork.
- Apply Method 1 to the pasted layer: Alpha Lock, new color, Fill Layer.
- Hide or delete the old lines on the original layer if they still show through underneath the new ones.
This method depends on how clean your original edges are. Heavily textured brushes or lines that blend into similar fill colors can leave stray pixels behind. If you see remnants, increase the selection threshold slightly or clean up with the eraser on the original layer.
Recoloring lines with more than one color
Alpha Lock stays useful after the first fill. With it still active on your line layer, you can paint with any brush and the strokes only appear where lines already exist. That lets you:
- Shift a line from one hue to another across a drawing, such as warm tones near a light source and cool tones in shadow.
- Add accent colors to specific shapes without selecting them.
- Hand-paint a gradient along a contour by sweeping a soft brush across the lines.
To return to a single color later, choose that color and run Fill Layer again. Fill Layer overwrites everything on the layer, so previous multi-color work is replaced.
Non-destructive alternatives
Fill Layer permanently changes pixels. If you want to keep the original black lines available, there are a few safer routes.
Duplicate first
Swipe left on the line layer and tap Duplicate, hide the original, and recolor the copy. This is the simplest version control Procreate offers, and it costs nothing but a layer slot.
Use a clipping mask
Create a new layer above the line art, tap it, and choose Clipping Mask. Anything you paint on the clipped layer only shows where the line layer has pixels. You can fill it with a color, paint gradients, or change its blend mode, and delete it to get the original lines back. It behaves like Alpha Lock, but the color lives on a separate layer.
Use Adjustments
For a quick global shift, open Adjustments (the magic wand icon) and try Hue, Saturation, Brightness on the line layer. This works best when your lines are already colored and you want to nudge them. For pure black lines, hue shifts do nothing, because black has no hue to rotate. In that case, use Fill Layer or a clipping mask.
Gradient Map for tonal control
Gradient Map, also under Adjustments, can remap the tonal range of a line layer to a custom gradient. It's a good option if you want the darkest parts of your lines to go deep blue and the lightest edges to go a warm tone, though it takes more setup than a simple fill.
Troubleshooting common problems
The whole layer turned a solid color. Alpha Lock was not on. Undo and enable it before running Fill Layer.
A thin black halo remains. This usually means some of the outline sits on a different layer, such as a shadow or texture layer. Check that no other layer contains the same outline. If you used the merged-layer method, enlarge the selection threshold and repeat.
Colors look different after export. Exported files can look different when opened in other software. If color matching matters, check the canvas color profile in your canvas settings and make sure the destination app interprets it the same way.
Painting on the line layer is blocked. Alpha Lock is probably still active. Turn it off to draw new strokes beyond the existing pixels.
You want to recolor many files. These steps are applied one canvas at a time, so if you have dozens of assets, consider recoloring downstream in your compositing app (see below).
Getting recolored lines into After Effects and other tools
Procreate fits well as an asset source for motion work, as long as you export with the right settings.
- Export as PNG with a transparent background. Hide the background color layer in the Layers panel before exporting, otherwise the file will have a solid backdrop.
- Export as PSD to keep layers. A layered PSD keeps line art independent from fills.
- Consider leaving lines black. If you plan to animate, a black or white line layer lets you recolor non-destructively in your compositing app and animate the color over time.
- Name layers before exporting. Clear names such as "lines," "fills," and "shadows" save time when the file lands in a comp.
Recoloring in Procreate is best for final stills and illustration. For anything animated or likely to change, a neutral line layer plus a recolor in compositing gives you more room to revise.
Where Styleframe fits
Recoloring lines in Procreate is a manual, per-canvas task, and it is the right tool for hand-drawn assets. When the job moves from a single drawing to a moving sequence, the question changes from "how do I change this line color" to "how do I keep a consistent line look across many frames."
Styleframe is an AI video and motion tool built for artists who want direct control over the result. It uses reference images or video clips to guide the look of your line work, color, and shading rather than relying on a text prompt alone.
In practice, you might draw a few key frames or a style board in Procreate, recolor the lines to match your palette, and use those as references in Styleframe. You can then bring the results into your compositing app, which keeps your usual workflow intact. Styleframe doesn't replace the careful hand work you do in Procreate. It extends your reference art into motion while you retain control of the look.
Quick recap
- Lines on their own layer: Alpha Lock, pick a color, Fill Layer.
- Lines merged with fills: Selection tool in Automatic mode, copy the line pixels to a new layer, then recolor that layer.
- For multi-color lines, paint on the Alpha Locked layer.
- For non-destructive edits, duplicate the layer or use a clipping mask.
- For animation work, export a transparent PNG or layered PSD, and consider recoloring in your compositing app so the color stays adjustable.