How to Recolor Line Art in Procreate
StyleFrame Team7 min read
To recolor line art in Procreate, turn on Alpha Lock for the line layer, pick a new color, then tap the layer and choose Fill Layer. Alpha Lock confines the fill to pixels that already exist, so every line takes the new color and the transparent areas stay clear. For a non-destructive version, put a new layer above the lines, clip it to them, and fill the clipped layer with the color you want.
Method 1: Alpha Lock and Fill Layer
This is the quickest way to change the color of line art that sits on its own transparent layer. It works for a single flat color.
- Open the Layers panel and find the layer that holds your lines.
- Tap the layer and choose Alpha Lock. A blue indicator on the layer lights up when it's active.
- Tap the color swatch at the top right and choose your new color.
- Tap the layer again and select Fill Layer.
Every non-transparent pixel now carries the new color, so you won't see leftover black pixels when you zoom in. Turn Alpha Lock off when you want to draw freely again.
Because Alpha Lock stays on, you can also paint over the lines with any brush and the strokes stay inside the existing linework. That makes it easy to add a second or third color to different parts of the drawing without selections or masks.
To go back, fill the layer with black the same way.
Method 2: Drag a color with ColorDrop
If you'd rather skip the menu, you can try keeping Alpha Lock on and dragging the color from the swatch at the top right onto the canvas. Check that the drop only affects the lines on that layer before you rely on it.
This is handy for quick tests. Drop in a color, judge it against the background, and drop in another. The result is destructive, though, because the original color is overwritten. If you might want the black version back, duplicate the layer first or use the clipping mask method below.
Method 3: A clipping mask for non-destructive recoloring
For client work with revisions, a clipping mask is the safer choice. Your original lines stay untouched, and the color lives on a separate layer you can change at any time.
- Add a new layer directly above the line art.
- Tap the new layer and choose Clipping Mask. It now only shows where the layer below has pixels.
- Fill the clipped layer with your color.
- To change the color later, select the clipped layer and re-fill it, or open Adjustments > Hue, Saturation, Brightness and slide the hue.
The clipped layer can hold more than a flat fill. You can paint gradients or textures on it, or stack several clipped layers with different blend modes. Hide the clipped layer and the original black lines reappear.
Hue shifting is another reason to prefer a clipped color layer. Hue sliders do nothing to pure black or white, so adjusting the hue of black line art directly won't give you a colored result. Fill first, then adjust.
Method 4: Recoloring line art on a white background
Scans and flattened exports usually have opaque white behind the lines, so Alpha Lock has nothing to isolate. There are a few workarounds.
Use blend modes. Put a clipping layer above the white-background line art, fill it with your target color, and set its blend mode to Lighten. Black pixels take on the color, while white pixels stay white because Lighten keeps the lighter of the two values. You can then switch the original line layer to Multiply so it composites over any colors you put underneath.
Remove the white. Use the Selection tool in Automatic mode to select the white areas, then clear them. Check the edges afterward. Anti-aliased pixels that are neither black nor white can leave a faint halo, so adjust the selection threshold and inspect at full zoom.
Redraw or trace on a transparent layer. For short, simple pieces, this can be quicker than cleaning up a messy scan.
If you're starting fresh, draw your lines on a transparent layer from the beginning. It makes every later step easier.
Recoloring with more than one color
Flat fills aren't always enough. A few options for more variation:
- Alpha Lock plus painting. With the lock on, paint different colors onto different parts of the lines with a soft or hard brush. Strokes stay inside the linework.
- Selection first. Select a region with Freehand or Automatic, then fill within that selection to recolor only part of the drawing.
- Gradient Map. Under Adjustments, Gradient Map remaps tonal values to a color gradient. It can turn dark lines into a range of colors, though results depend on the values in your artwork, so test it on a duplicate layer.
- Separate layers per element. If you know you'll need to recolor characters, props, and backgrounds independently, keep each on its own layer from the start. It takes seconds to set up and saves a lot of masking later.
Troubleshooting common problems
Only part of the line changed. Make sure you're on the right layer. Lines drawn across multiple layers need to be recolored layer by layer, or merged first.
The fill color covers the whole layer. Alpha Lock wasn't active, or the layer has a solid background. Check that the Alpha Lock indicator on the layer is lit.
Edges look jagged or dark. Fill Layer on an Alpha Locked layer preserves the soft edges. If you used a selection-based method, feather the selection or redo the fill using Alpha Lock.
Colors look different on export. Procreate canvases default to a particular color profile. If the output looks off in your compositing software, check the profile you exported with against the one in your project.
Lines vanish when colored under them. The line layer needs to sit above your color layers, or be set to Multiply when it's black on white.
Taking recolored line art into After Effects
If you're a motion designer, the Procreate file is probably the starting point rather than the final piece. A few habits make the handoff smoother.
- Export layers, not a flat image. Procreate can export PSD with layers intact, and After Effects imports it as a composition with each layer separate. PNG exports with transparency are fine for single elements.
- Keep lines on their own layer. You'll often want to adjust color again in the composite, and a separate transparent line layer lets you do it without going back to Procreate.
- Recolor in AE when it's faster. On a transparent line layer, the Fill effect, Tint, or Change to Color can swap the color without a round trip to the iPad. For quick revisions, this is often more practical than re-exporting.
- Check resolution. A canvas sized for a sketch may be too small for a 4K timeline. Set canvas dimensions for the final output before drawing, or plan to upscale later.
In Premiere Pro, Cinema 4D, Blender, and Nuke the same principle applies. Deliver clean transparent line layers and decide where the color decisions will be made.
When recoloring becomes a style problem
Recoloring a single drawing is a simple task. Carrying a consistent look across a whole sequence is harder. Once the line art needs to move, change over time, or match a reference look across dozens of shots, hand-recoloring every frame stops being practical.
This is where fits as a complement to Procreate. It's an AI video and motion tool. Your compositing workflow stays where it is: Procreate handles the illustration, Styleframe can help extend the look into motion, and your compositor handles final color, grain, and delivery.
None of this replaces learning the Procreate basics. A clean, well-organized layer structure makes every downstream step, including AI-assisted ones, more predictable.
Quick reference
Final tips
Name your layers, keep lines isolated on transparent layers, and duplicate before any destructive fill. Those three habits solve most recoloring problems before they start. Once the technique is second nature, recoloring takes seconds, and you can spend your time on the parts of the pipeline that need your judgment.