How to Quickly Fill in Procreate
StyleFrame Team7 min read
A fast way to fill in Procreate is ColorDrop. Drag the color from the top-right swatch into a closed shape, keep your pen down, and slide left or right to set the threshold. Then tap Continue Filling to flood other areas with single taps. For flats on a separate layer, mark your line art as a Reference layer first, so fills land beneath the lines instead of flooding the whole canvas.
Start with ColorDrop and Continue Filling
ColorDrop is Procreate's paint bucket.
- Pick your color in the top-right swatch.
- Drag it onto the area you want to fill and keep your pen or finger down.
- Pause until the threshold readout appears at the top of the canvas, then slide left (less fill) or right (more fill).
- Lift to commit.
Right after a ColorDrop, a Continue Filling option appears. Tap it and every following tap on the canvas fills with the same color. You can also tap, hold, and drag to change the threshold on the fly. Exit by tapping the tick or switching to another tool like Paint.
If your iPad and Apple Pencil support hover, you can hover over the active color swatch and double-tap the side of the Pencil to jump straight into Continue Filling. That removes the initial drag.
Why the threshold matters
The threshold controls how much the fill bleeds over the edges of the area you tapped. Set it too high and the color floods well beyond your shape. Set it too low and the fill may stop short of the edges. Procreate remembers the last threshold you used, so if a fill suddenly behaves differently, check whether you changed it on the previous drop.
Keep fills and line art on separate layers with a Reference layer
A common complaint is that ColorDrop floods an entire layer when you try to fill between lines drawn on a different layer. The fix is a Reference layer.
- Open the Layers panel and tap the line art layer to open its options.
- Choose Reference.
- Create a new layer underneath the line art for your flats.
- Select the new layer and ColorDrop into the enclosed areas.
Procreate now reads the boundaries from the line art layer but paints on the active layer. This keeps your drawing non-destructive. You can recolor, swap, or delete the flats layer without touching the lines, which matters when a client changes a palette late in the project.
A practical layer order for character or storyboard work:
- Line art on top (set as Reference)
- Flats on one or more layers below
- Shading or texture layers clipped to the flats
- Background at the bottom
Use Selections with Color Fill
When the shape is not outlined, or you need a precise geometric area, Selections with Color Fill is quicker than painting.
- Tap Selections.
- Choose a method at the bottom: Automatic, Freehand, Rectangle, or Ellipse.
- Turn on Color Fill (it shows blue when active).
- Pick your color.
- Make the selection. The fill is applied as soon as you complete it.
This works well for panels, color blocks, frames, and vignette shapes. Adding Feather from the Selections tools softens the edge for a glow or a soft border. Two cautions:
- Color Fill works on a single layer, not a layer group.
- The setting persists after you leave Selections, so turn it off when you are done. Otherwise your next selection will unexpectedly fill with color.
Fill an entire layer or shape with Fill Layer and Alpha Lock
For whole-layer fills, use Fill Layer. Choose a color, open the Layers panel, tap the target layer to open its options, and choose Fill Layer. This is the quickest way to make a solid background or to reset a layer to one color.
For recoloring an existing shape without spilling outside it, use Alpha Lock:
- Tap the layer thumbnail and choose Alpha Lock.
- Paint, ColorDrop, or Fill Layer onto it. Only existing pixels change; transparent areas stay transparent.
Alpha Lock is the cleanest option for a logo, a lettering piece, or a silhouette because you can paint carelessly and still stay inside the shape. It is also the starting point for gradients: with Alpha Lock on, draw a gradient across the layer and it clips to the artwork.
Another technique is to put the shape in solid black, add a gradient layer above it, and set that layer's blend mode to Lighten. The gradient shows only where it is lighter than the layer beneath. Clipping masks give you a similar result for patterns: put the pattern layer above the base shape and clip it, so the pattern appears only inside the shape.
Use Recolor when you want a different workflow
Procreate also has Recolor, an older tool that was brought back. It is only reachable through QuickMenu, which is off by default. To enable it, go to Actions → Prefs → Gesture Controls → QuickMenu and choose how you want to trigger it. Assign Recolor to one of the radial slots, tap it, select your color, and then tap the areas to fill. A Flood slider controls how aggressive the fill is.
Recolor is a matter of preference. Some artists find it more direct than ColorDrop for swapping many colors in finished art, since you tap to replace rather than drag to drop. If you already work fluently with ColorDrop and Continue Filling, there is little reason to switch.
Fix leaks, halos, and gaps
Procreate's fill tools do not include a gap-closing option like some dedicated inking and flatting apps. Artists who rely on loose, open line work notice this first. Here is how to work around it.
Leaking fills. If the fill spills outside your shape, there is almost certainly a gap in the line art. Zoom in and close it with a small brush stroke on the line layer, or lower the threshold. If you want to avoid altering the lines, add a temporary layer, patch the gap there, include that layer in your reference, and delete it afterward.
Light halos along edges. Anti-aliased line edges can leave a thin fringe of the old color. Raise the threshold a little so the fill extends under the line, and make sure the flats layer sits below the line art so the overlap is hidden.
Fill that covers the whole layer. Either the threshold is set too high or you are painting on a different layer from the line art without a Reference layer. Check both.
Crisp edges for hard-edged graphics. Because Procreate selections and lines are anti-aliased, flat-color work meant for tight graphic shapes can look slightly soft when scaled. If you plan to scale art up heavily in After Effects, draw at a higher canvas resolution than you think you need, or keep the shapes as vectors elsewhere and use Procreate for the textured elements.
Habits that make filling faster
- Work in flats first. Fill every shape with a base color before any shading. Recoloring a flat layer is much faster than fixing painted detail.
- Name and color-code layers. When you export layers to After Effects, clear names save time on import.
- Lock transparency by default on any layer you plan to recolor repeatedly.
- Keep a swatch palette so you can drag colors directly from the palette instead of switching colors in the picker.
- Use the right tool for the shape. Enclosed outline: ColorDrop with a Reference layer. Geometric area: Selections with Color Fill. Whole canvas or layer: Fill Layer. Existing shape: Alpha Lock.
Moving finished fills into a motion pipeline
If you use Procreate for styleframes, storyboards, or textured elements, the fills are only the first stage. Export your layered artwork, bring it into After Effects, and animate from there. Keeping flats on separate layers pays off here, since you can parallax, rig, or recolor elements in the comp without redoing anything in Procreate.
Fill speed becomes less relevant when the task is not one illustration but dozens or hundreds of frames in a consistent look. For that kind of work, you may want to look at tools built for extending a reference style across frames, such as . Procreate remains the place where you establish the look.
Quick reference: which fill method to use
Learn the ColorDrop threshold gesture and the Reference layer setup first. Those two cover most of the time you would otherwise spend filling by hand, and the rest of the methods handle the edge cases.